• Geomechanics and Engineering
• /
• v.24 no.6
• /
• pp.589-597
• /
• 2021

The present study evaluates geocell reinforced slope behavior. A three dimensional analysis is carried out to simulate soil and geocell elastoplastic behavior using the finite difference software FLAC3D. In order to investigate the geocell reinforcement effect, the geocell aperture size, thickness, geocell placement condition and soil compaction had been considered as variable parameters. Moreover, a comparison is evaluated between geocell reinforcing system and conventional planar reinforcement. The obtained results showed that the pocket size, thickness and soil compaction have considerable influence on the geocell reinforcement slope performance. Moreover, it was found that the critical sliding surface was bounded by the first geocell reinforcement and the slope stability increases, by increasing the vertical space between geocell layers. In addition, the comparison between geocell and geogrid reinforcement indicates the efficiency of using cellular honeycomb geosynthetic reinforcement.

• Journal of the Korean Geotechnical Society
• /
• v.22 no.5
• /
• pp.83-91
• /
• 2006

Recently, the intensive rainstorm possibly induced by global warming plays a key role on the instability of railway adjacent slopes. The instability of slopes results as covering and loss of railway lines induced by slided soil mass. According to the site investigation on the failed slopes triggered by rainfall, low types of slope failure were observed: shallow, intermediate, gully erosion, and soil-rock interface failures. The observation reveals the different characteristics of slope failure depending on the thickness of soil layer, morphological features of slope, etc. Based upon the observations, flume tests were conducted to analyze the sliding mechanism of each failure. The variables of flume test are soil layer thickness, rainfall intensity, and morphology of slope under the constant condition of the percentage of fine, initial soil moisture content, slope angle and compaction energy. Test results show that shallow failure was mostly observed from the surface of the slope and caused by the soil erosion; in addition, compared to the other types of failure, the occurrence of initial erosion is late, however, the development of erosion is fast. In gully erosion failure, the collected water from the water catchment area helps erosion of the upper soil layer and transfer of residual corestone, which impedes the erosion process once the upper soil layers are eroded and corestone are exposed. The soil-rock interface failure shows the most fast initial erosion process among the failure types. Interestingly, the common feature observed from the different types of failure was the occurrence of the initial deformation near the toe of slopes which implies the existence of surbsurface flow along the downslope direction.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.4 no.1
• /
• pp.101-110
• /
• 2000

In case heavy rainfall is a key factor of slope failure, the failure zone is usually developed within the depth of 3~5m from the ground surface regardless of the location of the watertable. If rainfall is taken into consideration, it is general that the slope stability analysis is carried out under the assumption that the cut slope is saturated to the slope surface or the watertable elevates to a certain height so that ${\gamma}_{sat}$, the unit weight of saturated soil, is used. However, the analysis method mentioned above can't exactly simulate the variation of pore water pressure in the slope and yields different failure shape. The applicability of slope stability analysis method considering the distribution of pore water pressure within the slope with heavy rainfalls, was checked out after the stability analysis of a lage-scale cut slope in a highway construction site, where surface failure occurred with heavy rainfalls. An appropriate slope stabilization method is proposed on the base of the outcome of the analysis.

• Proceedings of the KSEG Conference
• /
• 2003.04a
• /
• pp.153-158
• /
• 2003

Traditionally, the statistical methods has been used to analyze the relationship between landslide occurrence and related factors(soil depth, soil strength, slope angle, vegetation, etc.) in GIS technique. However, the method have no mechanical meaning. Therefore, the mechanical model is suggested in this research. The method analyzes the mechanical equilibrium of a potential slide block and then calculates a slope safety factor. Since this method is able to consider the balance of forces applied to the slope and is a more reasonable method for an individual site. In this research, the spatial data is obtained, managed and analyzed using GIS technique, and the infinite slope model is used to evaluate factor of safety and analyze the slope stability.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2008.03a
• /
• pp.399-404
• /
• 2008

The influence of gas hydrate dissociation on submarine slope stability was studied in this paper. Gas hydrates are stable under high pressure and low temperature conditions. Once gas hydrate dissociates due to natural or human activities, it generates large amount of gas and water. During gas hydrate dissociation, a pore pressure between soil particles increases and results in the loss of an effective stress and degradation of soil stiffness. A pore pressures model was proposed to calculated excess pore pressures generated by gas hydrate dissociation at the Storegga Slide. A slope stability analysis for the Storegga Slide using a two dimensional finite difference method was carried out by considering excess pore pressures due to gas hydrate dissociation. Since the excess pore pressure calculated by the proposed method resulted in the considerable loss of stiffness and strength in slope, a submarine slope failure occurred at the Storegga slide was well simulated.

• Journal of the Korean Geotechnical Society
• /
• v.38 no.8
• /
• pp.39-52
• /
• 2022

Multilayer perceptron neural network was trained to determine the factor of safety and slip surface of the slope. Slope geometry is a simple slope based on Korean design standards, and the case of dry and existing groundwater levels are both considered, and the properties of the soil composing the slope are considered to be sandy soil including fine particles. When curating the data required for model training, slope stability analysis was performed in 42,000 cases using the limit equilibrium method. Steady-state seepage analysis of groundwater was also performed, and the results generated were applied to slope stability analysis. Results show that the multilayer perceptron model can predict the factor of safety and failure arc with high performance when the slope's physical properties data are input. A method for quantitative validation of the model performance is presented.

• Journal of the Korean Geosynthetics Society
• /
• v.12 no.2
• /
• pp.67-74
• /
• 2013

In this study, the prediction of slope hazard probability was performed to the study area located in Hadae-ri, Woochun-myeon, Hoengsung-gun, Gangwon Province around Youngdong express way using the computer program SHAPP ver 1.0 developed by a decision tree model. The soil samples were collected at total 10 points, and soil tests were performed to measure soil properties. The thematic maps of soil properties such as coefficient of permeability and void ratio were made on the basis of soil test results. The slope angle analysis of topography was performed using a digital map. As the prediction result of slope hazard probability, 2,120 cells among total 27,776 cells were predicted to be in the event of slope hazards. Therefore, the predicted area of occurring slope hazards may be $53,000m^2$ because the analyzed cell size was $5m{\times}5m$.

• Geomechanics and Engineering
• /
• v.14 no.4
• /
• pp.345-354
• /
• 2018

Currently, layered geogrid method (LGM) is the commonly practiced technique for reinforcement of slopes. In this paper the geogrid-box method (GBM) is introduced as a new approach for reinforcement of rock-soil slopes. To achieve the objectives of this study, a laboratory setup was designed and the slopes without reinforcements and reinforced with LGM and GBM were tested under the loading of a circular footing. The effect of vertical spacing between geogrid layers and box thickness on normalized bearing capacity and failure mechanism of slopes was investigated. A series of 3D finite element analysis were also performed using ABAQUS software to supplement the results of the model tests. The results indicated that the load-settlement behavior and the ultimate bearing capacity of footing can be significantly improved by the inclusion of reinforcing geogrid in the soil. It was found that for the slopes reinforced with GBM, the displacement contours are widely distributed in the rock-soil mass underneath the footing in greater width and depth than that in the reinforced slope with LGM, which in turn results in higher bearing capacity. It was also established that by reducing the thickness of geogrid-boxes, the distribution and depth of displacement contours increases and a longer failure surface is developed, which suggests the enhanced bearing capacity of the slope. Based on the studied designs, the ultimate bearing capacity of the GBM-reinforced slope was found to be 11.16% higher than that of the slope reinforced with LGM. The results also indicated that, reinforcement of rock-soil slopes using GBM causes an improvement in the ultimate bearing capacity as high as 24.8 times more than that of the unreinforced slope.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.5 no.1
• /
• pp.43-54
• /
• 2003

In the deign of cut and cover tunnel, the structural analysis such as rigid frame analysis has been used for its simplicity and convenience. The structural analysis, however, can not consider the geological and geotechnical factors such as soil arching effect. In this study, the dominant factors influencing the behavior of cut and cover tunnel such as interface element, slope of excavation plane, distance between slope and tunnel lining, and location of slope of covered soil, were investigated by the numerical analysis to develop the analysis technique and design technology. Based on the results, the variation of bending moment, shear stress, axial force and displacements were evaluated and analyzed for each factor.

• Journal of the Korean Institute of Landscape Architecture
• /
• v.27 no.5
• /
• pp.80-93
• /
• 2000

This study measured the shearing resistance of the roots of the Pinus Koraiensis by the tensile strength gained through their individual tensile test for the Root Reinforcement Model. On the basis of the shearing resistance value calculated through such a process the factor of safety(Fs) was comparatively presented by using the simplified Janbu Method in PCSTABL5M, the slop-analyzing software which had been developed in Purdue University of the U.S.A according to the shape of a slope and the type of soil. The results to have measured a stress and the factor of safety(Fs) by experiment are as follows. 1) The mean root diameter of the Pinus Koraiensis used for this experiment was 2.483mm and the mean tensile stress was calculated as 422.846(kgf/$\textrm{cm}^2$). In the strain ratio of material and the elastic modulus was measured 7.8%, 9,291.92(kgf/$\textrm{cm}^2$). 2) The shearing strength including the resistance of soil and root is expressed as Rt=C+Cr+$\sigma$.tan . ΔCr(kg/$\textrm{cm}^2$) of the shearing resistance calculated by estimating the areal ratio of roots at 10 is 0.253(kgf/$\textrm{cm}^2$). 3) As the result of making an analysis of the natural slope stability by the soil parameter, the factor of safety(Fs) was calculated at 1.795 in CL, and the stability analysis of the root reinforcement slope, Fs was calculated at 1.952. However, since a precise analysis of the controlled factors of the slope analyses are demanded for more accurate dynamic analyses, the future demands a study on this.