• Proceedings of the Korean Geotechical Society Conference
• /
• 2008.10a
• /
• pp.1204-1211
• /
• 2008

Compression index is one of the important characteristic numbers in soft soil engineering. Since 1940's, many researchers have suggested various practical solutions to define the compression index of clay using other soil properties. But, these results are only can give us an outline of soft soil behavior. In this study, the relationships between pore water pressure dissipation test results and compression index were suggested using comparison results of both tests. This relationships are based on basic concept of consolidation phenomena, essential difference between pore water pressure dissipation test and consolidation test, and disagreements between theoretical time factor and real time factor. To identify proportional factor of proposed equation, Geotechnical investigation results of Kwang-Yang(KY) site and Busan New Port(BN) site were used. The proportional factor was 0.0031 from 20 to 50% of consolidation rate where correlation parameter($R^2$) is 0.9051.

• Journal of the Korean GEO-environmental Society
• /
• v.9 no.1
• /
• pp.33-40
• /
• 2008

In this research, model tests have been performed for researching the seepage characteristics in the finite soil slope during the rainfall using a manufactured rainfall simulator. On the basis of the results, it has been analyzed how to change the seepage characteristics due to the duration time of rainfall. We are found that the pore-water pressure was gradually increased as increasing the duration time of rainfall. Specially, at the beginning of rainfall, the pore-water pressure in the middle surface of slope was measured larger than any point. As increasing the duration time of rainfall, the pore-water pressure at the inner part of slope was increased greatly at the collapse due to infiltrating the pore-water within the slope. In the research, it was not easy to get various test results because measuring instruments are high sensitivity and difficult to handle. For the future, the model test results are needed for the various slope angle.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2007.09a
• /
• pp.481-501
• /
• 2007

Excessive rainfalls due to climatic changes can trigger an increase in rainfall-induced slope failures that pose real threats to both lives and properties. Many high slopes in residual soils could stand at a steep angle, but failed during or after rainfall. Commonly, these slopes have a deep groundwater table and negative pore-water pressures in the unsaturated zone above the groundwater table contribute to the shear strength of soil and consequently to factor of safety of the slope. Stability assessment of slope under rainfall requires information on rate of rainwater infiltration in the unsaturated zone and the resulting changes in pore-water pressure and shear strength of soil. This paper describes the application of unsaturated soil mechanics principles and theories in the assessment of rainfall effect on stability of slope through proper characterization of soil properties, measurement of negative pore-water pressures, seepage and slope stability analyses involving unsaturated and saturated soils. Factors controlling the rate of changes in factor of safety during rainfall and a preventive method to minimize infiltration are highlighted in this paper.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2005.03a
• /
• pp.1140-1147
• /
• 2005

The objective of this study was to identify the effect of the degree of saturation on the resilient modulus of cohesive soils as subgrade. Six representative cohesive soils representing A-4, A-6, and A-7-6 soil types collected from road construction sites across Ohio, were tested in the laboratory to determine their basic engineering properties. Resilient modulus tests were conducted on unsaturated cohesive soils at optimum moisture content, and samples compacted to optimum conditions but allowed to fully saturate. The subgrade compacted at optimum moisture content may be fully saturated due to seasonal change. Laboratory tests on fully saturated cohesive soils showed that the resilient modulus of saturated soils decreased to less than half that of soil specimens tested at optimum moisture content. The reduction of resilient modulus would possibly be caused by the buildup of pore water pressure. In resilient modulus testing performed in this study on saturated samples, pore water pressure increases were observed. Pore water pressure and residual pore water pressure gradually increased with an increase in deviator stress.

• Journal of the Korean Geotechnical Society
• /
• v.15 no.5
• /
• pp.291-300
• /
• 1999

Surfactant flushing for enhancing the removal of BTEX from contaminated sand/clay mixtures was investigated. Eight soil columns packed with relatively undisturbed BTEX contaminated soils, were leached with water, methyl alcohol and then flushed with surfactant with or without several additives. Initial concentrations of BTEX mixture range from 278mg/kg to 1975mg/kg. Initial BTEX removal efficiency was 98% when the contaminated soil was flushed with water of 850 pore volumes. Because of tailing effect, water flushing could not remove below 8mg/kg concentrations during the experimental period. Eventually, the most effective surfactant for flushing was turned out to be 4% SOFTANOL(equation omitted)-90 with 3% ethyl alcohol and 3% SXS. In interrupted flow conditions, the removal efficiency was 99.5% with the flushed water of 95 pore volumes. The BTEX mixture removed from the soil columns during the surfactant flushing ranges from 84.5% to 99.5% of the initial amount for both water leaching(850 pore volumes) and surfactant flushing(95-165 pore volumes), respectively. Test results indicated that surfactant flushing could enhance the removal of BTEX mixture from contaminated soils and could reduce the aqueous phase BTEX mixture concentration in leachate.

• Korean Journal of Soil Science and Fertilizer
• /
• v.26 no.4
• /
• pp.284-288
• /
• 1993

Tow Kinds of Soils, vertisol and alfisol, were selected and analyzed pore space distribution(PSD) by mercury intrusion method and soil water potential after freeze-drying from different water conditions, such as 0.033MPa, 1.5MPa and ovendry. The PSD values measured by mercury intrusion method were higher in large pores than the values from soil water potential. Also, there were big differences of PSD by the changes of the water content befor freeze-drying.

• Nuclear Engineering and Technology
• /
• v.32 no.4
• /
• pp.342-349
• /
• 2000

A soil whose texture is silt loam was collected for the study from an area around a nuclear facility in Korea. The equilibrium sorption coefficient between Co$^{2+}$in water and the soil was 1.51/kg, on the other hand, that between Co$^{2+}$ in EDTA and the soil was 0.21/kg. The values calculated by the developed nonequilibrium sorption code corresponded to the experimental values better than those calculated by the existing equilibrium sorption code. When an EDTA solution was used as a solvent to decontaminate Co$^{2+}$ in the soil column, the relative Co$^{2+}$ concentrations of the effluent were higher at 2~10 pore volumes than those of the case using water. The soil in the column was decontaminated by 95.5% of the total amount of Co$^{2+}$ after being flushed with EDTA solution of 20 pore volumes.e volumes.

• Journal of The Korean Society of Agricultural Engineers
• /
• v.46 no.6
• /
• pp.61-69
• /
• 2004

The aim of the work described in this paper was to confirm the application of the equation of the soil-water characteristic curves on an unsaturated soil. A series of suction test for unsaturated soils was conducted on the selected 4 kinds of soil using modified pressure extractor apparatus. And it was carried out to analyse The experimental parameters which can be describe the soil-water characteristics, were determined by using the data obtained from the experiment. From the results, it was found that The matric suction varied according to the grain size distribution, amount of fine grain particles and void ratio. Also it was found that the residual degree of saturation was decreased with in crease of the void ratio, but the pore size distribution index and air entry value were increased with in crease of the void ratio. And The application of the soil-water characteristic curve equation was confirmed for the various conditions and the various state by the comparison between the measured degree of saturation and the predicted degree of saturation.

• Geomechanics and Engineering
• /
• v.30 no.2
• /
• pp.201-210
• /
• 2022

This paper presents a study regarding the influence of various water levels on the characteristics of subgrade mud pumping through a self-developed test instrument. The characteristics of mud pumping are primarily reflected by axial strain, excess pore water pressure, and fine particle migration. The results show that the axial strain increases nonlinearly with an increase in cycles number; however, the increasing rate gradually decreases, thus, an empirical model for calculating the axial strain of the samples is presented. The excess pore water pressure increases rapidly first and then decreases slowly with an increase in cycles number. Furthermore, the dynamic stress within the soil first rapidly decreases and then eventually slows. The results indicate that the axial strain, excess pore water pressure, and the height and weight of the migrated fine particles decrease significantly with a low water level. In this study, when the water level is 50 mm lower than the subgrade soil surface, the issue of subgrade mud pumping no longer exist.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.42 no.2
• /
• pp.71-77
• /
• 2000

A multi-region model for solute transport through saturated soils has been developed to describe preferential flow. The model consists of numerous discrete pore groups, which are characterized by a discrete dispersion coefficient, flow velocity, and porosity . The hydraulic properties for each pore group are derived from a soil's hydraluic conductivity and soil water characteristic functions . Flow in pore group is described by the classical advection-disersion equation (ADE). An implict finite difference scheme was applied to the governing equation that results in a block-tridiagonal system of equations that is very efficient and allows the soil to be divided into any number of pore groups. The numerical technique is derived from methods used to solve coupled equations in fluid dynamics problems and can also be applied to the transport of interacting solutes. The results of the model are compared to the experimental data from published papers. This paper contributes on the characteristics of the method when applied to the parallel porosity model to describe preferential flow of solutes in soil.