• Journal of The Korean Society of Agricultural Engineers
• /
• v.60 no.6
• /
• pp.83-96
• /
• 2018

The objective of this study was to estimate the climate change impact on water quantity and quality to Saemanguem watershed using SWAT (Soil and water assessment tool) model. The SWAT model was calibrated and validated using observed data from 2008 to 2017 for the study watershed. The $R^2$ (Determination coefficient), RMSE (Root mean square error), and NSE (Nash-sutcliffe efficiency coefficient) were used to evaluate the model performance. RCP scenario data were produced from 10 GCM (General circulation model) and all relevant grid data including the major observation points (Gusan, Jeonju, Buan, Jeongeup) were extracted. The systematic error evaluation of the GCM model outputs was performed as well. They showed various variations based on analysis of future climate change effects. In future periods, the MIROC5 model showed the maximum values and the CMCC-CM model presented the minimum values in the climate data. Increasing rainfall amount was from 180mm to 250mm and increasing temperature value ranged from 1.7 to $5.9^{\circ}C$, respectively, compared with the baseline (2006~2017) in 10 GCM model outputs. The future 2030s and 2070s runoff showed increasing rate of 16~29% under future climate data. The future rate of change for T-N (Total nitrogen) and T-P (Total phosphorus) loads presented from -26 to +0.13% and from +5 to 47%, respectively. The hydrologic cycle and water quality from the Saemanguem headwater were very sensitive to projected climate change scenarios so that GCM model should be carefully selected for the purpose of use and the tendency analysis of GCM model are needed if necessary.

• Computers and Concrete
• /
• v.24 no.2
• /
• pp.151-158
• /
• 2019

The sustainable development principle of replacing natural resources with renewable material is an important research topic. In this study, waste LCD (liquid crystal display) glass powder was used to replace cement (0%, 10%, 20% and 30%) through a volumetric method using three water-binder ratios (0.47, 0.59, and 0.71) to make cement mortar. The compressive strength was tested at the ages of 7, 28, 56 and 91 days. The test results show that the compressive strength increases with age but decreases as the water-binder ratio increases. The compressive strength slightly decreases with an increase in the replacement of LCD glass powder at a curing age of 7 days. However, at a curing age of 91 days, the compressive strength is slightly greater than that for the control group (glass powder is 0%). When the water-binder ratios are 0.47, 0.59 and 0.71, the compressive strength of the various replacements increases by 1.38-1.61 times, 1.56-1.80 times and 1.45-2.20 times, respectively, during the aging process from day 7 to day 91. Furthermore, a prediction model of the compressive strength of a cement mortar with waste LCD glass powder was deduced in this study. According to the comparison between the prediction analysis values and test results, the MAPE (mean absolute percentage error) values of the compressive strength are between 2.79% and 5.29%, and less than 10%. Thus, the analytical model established in this study has a good forecasting accuracy. Therefore, the proposed model can be used as a reliable tool for assessing the design strength of cement mortar from early age test results.

• Journal of The Korean Society of Agricultural Engineers
• /
• v.57 no.5
• /
• pp.1-12
• /
• 2015

The study aimed to project inflows and demmands for the agricultural reservoir watersheds in South Korea considering a variety of regional characteristics and the uncertainty of future climate information. The study bias-corrected and spatially downscaled retrospective daily Global Climate Model (GCM) outputs under Representative Concentration Pathways (RCP) 4.5 and 8.5 emission scenarios using non-parametric quantile mapping method to force Soil and Water Assessment Tool (SWAT) model. Using the historical simulation, the skills of un-calibrated SWAT model (without calibration process) was evaluated for 5 reservoir watersheds (selected as well-monitored representatives). The study then, evaluated the performance of 9 GCMs in reproducing historical upstream inflow and irrigation demand at the five representative reservoirs. Finally future inflows and demands for 58 watersheds were projected using 9 GCMs projections under the two RCP scenarios. We demonstrated that (1) un-calibrated SWAT model is likely applicable to agricultural watershed, (2) the uncertainty of future climate information from different GCMs is significant, (3) multi-model ensemble (MME) shows comparatively resonable skills in reproducing water balances over the study area. The results of projection under the RCP 4.5 and RCP 8.5 scenario generally showed the increase of inflow by 9.4% and 10.8% and demand by 1.4% and 1.7%, respectively. More importantly, the results for different seasons and reservoirs varied considerably in the impacts of climate change.

• Journal of Korean Society on Water Environment
• /
• v.25 no.5
• /
• pp.792-802
• /
• 2009

The objective of this study is to construct the watershed management system with link of the non-point sources model and to estimate delivery ratio duration curves for various pollutants. For the total water pollution load management system, non-point source model should be performed with the study of the characteristic about non-point sources and loadings of non-point source and the allotment of pollutant in each area. In this study, daily flow rates and delivered pollutant loads of Nakdong river basin are simulated with modified TANK model and minimum variance unbiased estimator and SWAT model. Based on the simulation results, flow duration curves, load duration curves, and delivery ratio duration curves have been established. Then GIS analysis is performed to obtain several hydrological geomorphic characteristics such as watershed area, stream length, watershed slope and runoff curve number. As a result, the SWAT simulation results show good agreements in terms of discharge, BOD, TN, TP but for more exact simulation should be kept studying about variables and parameters which are needed for simulation. And as a result of the characteristic discharges, pollutants loading with the runoff and delivery ratios, non-point sources effects were higher than point sources effects in the small-scale test bed of Nakdong river basin.

• Journal of Korean Society on Water Environment
• /
• v.29 no.5
• /
• pp.681-690
• /
• 2013

Watershed models have been increasingly used to support an integrated management of land and water, non-point source pollutants, and implement total daily maximum load policy. However, these models demand a great amount of input data, process parameters, a proper calibration, and sometimes result in significant uncertainty in the simulation results. For this reason, uncertainty analysis is necessary to minimize the risk in the use of the models for an important decision making. The objectives of this study were to evaluate three different uncertainty analysis algorithms (SUFI-2: Sequential Uncertainty Fitting-Ver.2, GLUE: Generalized Likelihood Uncertainty Estimation, ParaSol: Parameter Solution) that used to analyze the sensitivity of the SWAT(Soil and Water Assessment Tool) parameters and auto-calibration in a watershed, evaluate the uncertainties on the simulations of runoff and sediment load, and suggest alternatives to reduce the uncertainty. The results confirmed that the parameters which are most sensitive to runoff and sediment simulations were consistent in three algorithms although the order of importance is slightly different. In addition, there was no significant difference in the performance of auto-calibration results for runoff simulations. On the other hand, sediment calibration results showed less modeling efficiency compared to runoff simulations, which is probably due to the lack of measurement data. It is obvious that the parameter uncertainty in the sediment simulation is much grater than that in the runoff simulation. To decrease the uncertainty of SWAT simulations, it is recommended to estimate feasible ranges of model parameters, and obtain sufficient and reliable measurement data for the study site.

• Journal of Korea Water Resources Association
• /
• v.42 no.2
• /
• pp.161-168
• /
• 2009

The purpose of this study is to evaluate the variation of probability flood according to the flow regulation by multi-purpose dams (Soyang and Chungju) in the Han-river basin, Korea. SWAT-K (Soil and Water Assessment Tool-Korea) was used in order to generate regulated and unregulated daily streamflows upstream of Paldang dam. Simulated flow regulated by the Soyang and Chungju dams was calibrated by comparison with the observed inflow data at Paldang reservoir. Generally the ratio of flood flows to daily streamflows is known to decrease with drainage area in a watershed. Regulated and unregulated flood flows were obtained from the relationship between flood flows and daily streamflows. Extreme Type-I distribution was applied for flood frequency analysis and L-moment method was used for parameter estimation. This is a novel approach capable of understanding the variation in flood frequency with dam operation for the relatively large watershed scale, and this will helps improve the applicability of daily stream flow data for use in flood control as well as in water utilization.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2015.05a
• /
• pp.192-192
• /
• 2015

현재 우리나라는 점오염원 관리로 인한 수질개선 효과가 한계에 다다르고 있으며, 비점오염원의 수계별 총 부하 기여율이 지속적으로 증가하고 있어 추가적인 수질개선을 위해서는 비점오염원에 의한 오염부하량을 예측하고 관리하는 것이 필요하다. 국내에서는 비점오염원 관리를 위해 지속적으로 수질 모니터링을 실시하고 있으나 자료수가 부족하고 실측자료가 일부 존재하는 등의 단점을 가지고 있다. 부족한 자료는 환경부에서 제안한 원단위법 또는 분포형 수문모형을 이용하여 모의하고 있으나 원단위법은 유역특성을 고려하지 못한다는 단점을 가지고 있으며 분포형 수문모형은 모의에 많은 시간이 소요되는 단점이 있다. 본 연구에서는 유역특성을 고려하여 오염부하량을 산정하는 회귀식을 개발하고 적용성을 검토해보고자 한다. 회귀식 개발에 필요한 입력자료는 환경부 물환경정보시스템 (Water Information System, WIS)에서 제공하는 수질자료, 국가수자원관리종합정보시스템 (Water Resource Management Information System, WAMIS)에서 제공하는 수위-유량 자료, 용인시 백암면 일대에서 2013년부터 2014년까지 모니터링한 수질 및 유량자료를 이용하였다. 회귀식 도출에는 IBM SPSS Statistics 20 (SPSS, Inc, 2011)을 이용하였다. 개발된 회귀식 검토를 위해 미계측 유역을 대상으로 SWAT (Soil and Water Assessment Tool) 모형을 이용하여 오염부하량을 모의하였으며, 결과 비교를 통해 개발된 식의 타당성을 검토하였다. 본 연구의 결과는 유역에서 비점오염원에 의해 발생하는 오염부하량 모의를 통해 유역 내 비점오염원 저감대책 마련에 이용할 수 있을 것으로 사료된다.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.28 no.6B
• /
• pp.653-663
• /
• 2008

The purpose of this study is to establish a database of weather, hydrology, point source pollution management, reservoir release and tillage management for SWAT model evaluation of Anseongcheon watershed ($370.1km^2$, the upstream of Gongdo water level gauging station), and to use them for the following research of future climate and land use change impact on streamflow and stream water quality. It is expected that the database can achieve the practical analysis of current watershed hydrologic and environmental condition. The model calibration and validation were conducted using the constructed database. The model results showed that the tillage management affected the temporal shift of pollutant loads, and changed the flow pattern of pollutant transport through cultivation area. It was identified that the April and May irrigation water supply from the agricultural reservoir also affected the streamflow of downstream. The data application of pollutants treatment facilities and tillage management of cultivation area showed about 10% difference in the simulation results of stream water quality. The data establishment of agricultural reservoir operation, the tillage management of cultivated area within the watershed and the attributes inclusion of pollutants treatment facilities were proved to be important in SWAT model evaluation. The results of model setup in this study are expected for more reliable model application in the following research of future climate and land use change impact on hydrology and stream water quality of the study watershed.

• Environmental Engineering Research
• /
• v.25 no.3
• /
• pp.267-273
• /
• 2020

This Hydrokinetic energy system is the process of extracting energy from rivers, canals and others sources to generate small scale electrical energy for decentralized usage. This study investigates the application of Soil and Water Assessment Tool (SWAT) in Geographical Information System (GIS) environment to evaluate the theoretical hydrokinetic energy potentials of selected Rivers (Asa, Awun and Oyun) all in Asa watershed, Kwara state, Nigeria. SWAT was interfaced with an open source GIS system to predict the flow and other hydrological parameters of the sub-basins. The model was calibrated and validated using observed stream flow data. Calibrated flow results were used in conjunction with other parameters to compute the theoretical hydrokinetic energy potentials of the Rivers. Results showed a good correlation between the observed flow and the simulated flow, indicated by ash Sutcliffe Efficiency (NSE) and R² of 0.76 and 0.85, respectively for calibration period, and NSE and R² of 0.70 and 0.74, respectively for the validation period. Also, it was observed that highest potential of 154.82 MW was obtained along River Awun while the lowest potential of 41.63 MW was obtained along River Asa. The energy potentials obtained could be harnessed and deployed to the communities around the watershed for their energy needs.

• Journal of The Korean Society of Agricultural Engineers
• /
• v.59 no.2
• /
• pp.19-27
• /
• 2017

Recently, the hydrological model Soil Water Assessment Tool (SWAT) has been applied in many watersheds in South Korea. This study estimated parameters in SWAT for calibrating streamflow in long-term drought periods. Therefore, we focused on the continuous severe drought periods 2014~2015, and understand the model calibrated parameters. The SWAT was applied to a $366.5km^2$ Gongdo watershed by using 14 years (2002~2015) daily observed streamflow (Q) including two years extreme drought period of 2014~2015. The 9 parameters of CN2, CANMX, ESCO, SOL_K, SLSOIL, LAT_TIME, GW_DELAY, GWQMN, ALPHA_BF were selected for model calibration. The SWAT result by focusing on 5 normal years (2002~2006) calibration showed the 14 years average Nash-Sutcliffe model efficiency (NSE) for Q and 1/Q with 0.78 and 0.58 respectively. On the other hand, the 14 years average NSEs of Q and 1/Q by focusing on 2 drought years (2014~2015) calibration were 0.86 and 0.76 respectively. Thus, we could infer that the SWAT calibration trial by focusing on drought periods data can be a good approach to calibrate both high flow and low flow by controlling the 9 drought affected parameters.