• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.39 no.2
• /
• pp.327-333
• /
• 2019

For sustainable lunar exploration, the most required resources should be procured on site because it takes tremendous cost to transfer the resources from the Earth to the Moon. The technologies required for use of lunar resources refers to In-Situ Resource Utilization (ISRU). As the ISRU technology cannot be verified in the Earth, a lunar surface environment simulator is necessary to be prepared in advance. The Moon has no atmosphere, and the average temperature of the lunar surface reaches to $107^{\circ}C$ during the daytime and $-153^{\circ}C$ at night. The lunar surface is also covered with very fine soils with sharp particles that are electrostatically charged by solar radiation and solar wind. In this research, generation of vacuum environment with lunar soil mass in a chamber and simulation of electrostatically charged soils are taken into consideration. It was successful to make a vacuum environment of a chamber including lunar soils without soil disturbance by controlling evacuation rate of a vacuum chamber. And an experiment procedure for simulating the charged lunar soil was suggested by theoretical consideration in charging phenomena on lunar dust.

• Journal of the Korean GEO-environmental Society
• /
• v.12 no.6
• /
• pp.25-34
• /
• 2011

Dredged and reclaimed ground in progress at the West Coast has a high content of coarse particles. There will be different behaviors depending on the location of outlet and engineering properties of soil when its ground is dredged by a pump. Therefore, the experiments were conducted that were manufactured about the chamber equipment of length 2,650mm, width 770mm, height 735mm, experimented step filling method and water content about 300%, 500% and 700% respectively with SM and ML samples in order to realize segregating sediment characteristics of dredged ground with changing much fine. With results of analysis, ML sample by higher initial water content was reached to the period of complete sedimentation and coefficient of sedimentation consolidation increased with increases of diffusion distance. SM samples showed behavior of coarse soil with diffusion distance 120cm, diffusion distance of more than 120cm showed a similar tendency with ML sample under the influence of fines. In ML sample, it could be also found that lower depth and the more increasing diffusion distance increase in percentage of sieve #200 but water content decreases. In SM sample, it could be also found that coarse soil was piled at near the diffusion distance zone but fine soil was piled at the far diffusion distance zone and prominent difference showed between percentage of sieve #200 and water content(%) by boundary point 120cm~160cm of both samples. Also, shear strength was expressed ML-maximum 2.97kPa, SM-maximum 10.2kPa with diffusion distance.

• Journal of Drive and Control
• /
• v.20 no.4
• /
• pp.115-122
• /
• 2023

This study utilized a discrete element method (DEM) simulation, as one of the virtual field trials, to predict the impact of tillage depth on the rotary blade shaft during rotavator tilling. The virtual field for the simulation was generated according to soil properties observed in an actual field. Following the generation of particles for the virtual field, a sequence of calibration steps followed to align the mechanical properties more closely with those of real soil. Calibration was conducted with a focus on bulk density and shear torque, resulting in calibration errors of just 0.02% for bulk density and 0.52% for shear torque. The prediction of the load on a rotary tiller's blade shaft involved a three-pronged approach, considering shaft torque, draft force, and vertical force. In terms of shaft torque, the values exhibited significant increases of 42.34% and 36.91% for every 5-centimeter increment in tillage depth. Similarly, the vertical force saw substantial growth by 40.41% and 36.08% for every 5-centimeter increment. In contrast, the variation in draft force based on tillage depth was comparatively lower at 18.49% and 0.96%, indicating that the effect of tillage depth on draft force was less pronounced than its impact on shaft torque and vertical force. From a perspective of agricultural machinery research, this study provides valuable insights into the DEM soil modeling process, accounting for changes in soil properties with varying tillage depths. These findings are expected to be instrumental in future agricultural machinery design studies.

• Journal of Korean Society of Forest Science
• /
• v.66 no.1
• /
• pp.16-36
• /
• 1984

It is very important in forestry to study the shear strength of weathered granitic soil, because the soil covers 66% of our country, and because the majority of land slides have been occured in the soil. In general, the causes of land slide can be classified both the external and internal factors. The external factors are known as vegetations, geography and climate, but internal factors are known as engineering properties originated from parent rocks and weathering. Soil engineering properties are controlled by the skeleton structure, texture, consistency, cohesion, permeability, water content, mineral components, porosity and density etc. of soils. And the effects of these internal factors on sliding down summarize as resistance, shear strength, against silding of soil mass. Shear strength basically depends upon effective stress, kinds of soils, density (void ratio), water content, the structure and arrangement of soil particles, among the properties. But these elements of shear strength work not all alone, but together. The purpose of this thesis is to clarify the characteristics of shear strength and the related elements, such as water content ($w_o$), void ratio($e_o$), dry density (${\gamma}_d$) and specific gravity ($G_s$), and the interrelationship among related elements in order to decide the dominant element chiefly influencing on shear strength in natural/undisturbed state of weathered granitic soil, in addition to the characteristics of soil hardness of weathered granitic soil and root distribution of Pinus rigida Mill and Pinus rigida ${\times}$ taeda planted in erosion-controlled lands. For the characteristics of shear strength of weathered granitic soil and the related elements of shear strength, three sites were selected from Kwangju district. The outlines of sampling sites in the district were: average specific gravity, 2.63 ~ 2.79; average natural water content, 24.3 ~ 28.3%; average dry density, $1.31{\sim}1.43g/cm^3$, average void ratio, 0.93 ~ 1.001 ; cohesion, $ 0.2{\sim}0.75kg/cm^2$ ; angle of internal friction, $29^{\circ}{\sim}45^{\circ}$ ; soil texture, SL. The shear strength of the soil in different sites was measured by a direct shear apparatus (type B; shear box size, $62.5{\times}20mm$; ${\sigma}$, $1.434kg/cm^2$; speed, 1/100mm/min.). For the related element analyses, water content was moderated through a series of drainage experiments with 4 levels of drainage period, specific gravity was measured by KS F 308, analysis of particle size distribution, by KS F 2302 and soil samples were dried at $110{\pm}5^{\circ}C$ for more than 12 hours in dry oven. Soil hardness represents physical properties, such as particle size distribution, porosity, bulk density and water content of soil, and test of the hardness by soil hardness tester is the simplest approach and totally indicative method to grasp the mechanical properties of soil. It is important to understand the mechanical properties of soil as well as the chemical in order to realize the fundamental phenomena in the growth and the distribution of tree roots. The writer intended to study the correlation between the soil hardness and the distribution of tree roots of Pinus rigida Mill. planted in 1966 and Pinus rigida ${\times}$ taeda in 199 to 1960 in the denuded forest lands with and after several erosion control works. The soil texture of the sites investigated was SL originated from weathered granitic soil. The former is situated at Py$\ddot{o}$ngchangri, Ky$\ddot{o}$m-my$\ddot{o}$n, Kogs$\ddot{o}$ng-gun, Ch$\ddot{o}$llanam-do (3.63 ha; slope, $17^{\circ}{\sim}41^{\circ}$ soil depth, thin or medium; humidity, dry or optimum; height, 5.66/3.73 ~ 7.63 m; D.B.H., 9.7/8.00 ~ 12.00 cm) and the Latter at changun-long Kwangju-shi (3.50 ha; slope, $12^{\circ}{\sim}23^{\circ}$; soil depth, thin; humidity, dry; height, 10.47/7.3 ~ 12.79 m; D.B.H., 16.94/14.3 ~ 19.4 cm).The sampling areas were 24quadrats ($10m{\times}10m$) in the former area and 12 in the latter expanding from summit to foot. Each sampling trees for hardness test and investigation of root distribution were selected by purposive selection and soil profiles of these trees were made at the downward distance of 50 cm from the trees, at each quadrat. Soil layers of the profile were separated by the distance of 10 cm from the surface (layer I, II, ... ...). Soil hardness was measured with Yamanaka soil hardness tester and indicated as indicated soil hardness at the different soil layers. The distribution of tree root number per unit area in different soil depth was investigated, and the relationship between the soil hardness and the number of tree roots was discussed. The results obtained from the experiments are summarized as follows. 1. Analyses of simple relationship between shear strength and elements of shear strength, water content ($w_o$), void ratio ($e_o$), dry density (${\gamma}_d$) and specific gravity ($G_s$). 1) Negative correlation coefficients were recognized between shear strength and water content. and shear strength and void ratio. 2) Positive correlation coefficients were recognized between shear strength and dry density. 3) The correlation coefficients between shear strength and specific gravity were not significant. 2. Analyses of partial and multiple correlation coefficients between shear strength and the related elements: 1) From the analyses of the partial correlation coefficients among water content ($x_1$), void ratio ($x_2$), and dry density ($x_3$), the direct effect of the water content on shear strength was the highest, and effect on shear strength was in order of void ratio and dry density. Similar trend was recognized from the results of multiple correlation coefficient analyses. 2) Multiple linear regression equations derived from two independent variables, water content ($x_1$ and dry density ($x_2$) were found to be ineffective in estimating shear strength ($\hat{Y}$). However, the simple linear regression equations with an independent variable, water content (x) were highly efficient to estimate shear strength ($\hat{Y}$) with relatively high fitness. 3. A relationship between soil hardness and the distribution of root number: 1) The soil hardness increased proportionally to the soil depth. Negative correlation coefficients were recognized between indicated soil hardness and the number of tree roots in both plantations. 2) The majority of tree roots of Pinus rigida Mill and Pinus rigida ${\times}$ taeda planted in erosion-controlled lands distributed at 20 cm deep from the surface. 3) Simple linear regression equations were derived from indicated hardness (x) and the number of tree roots (Y) to estimate root numbers in both plantations.

• Korean Journal of Soil Science and Fertilizer
• /
• v.35 no.3
• /
• pp.137-144
• /
• 2002

To obtain the basic information about pedo-genetic properties and origin of the parent materials of "Yongil" series in Korea, this study was conducted. The soil characteristics such as chemical and sand particles of typifying pedon, and distributional patterns in the area were analysed. The typifying pedon of "Yongil" series was distributed on the top of rolling area in the eastern coastal area of Korea, Yonggan-ri, Heunghae-eup, Pohang-si, Gyongbuk province. The results are as follows; The "Yongil" series in Korea was distributed on the rolling hill under altituede of 50m, and was used for cultivated upland, and the total acreage about 376ha. The content of sand was more than 50%, however the clay content in the depth of 40~100cm of the soil profile rapidly increased. The medium sand (0.5~0.1mm in size) are dominant among sand fraction, but coarse one are rare. So the rate of medium to total sand was higher in IIB horizon as 0.62~0.76 than A and C horizons. The content of heavy minerals in medium sand was low as 1.0~6.6% and the ratio of quartz to feldspars was higher in Ap2 and B1 horizon as 1.7 than IIB horizon which had less than 1.39. The cumulative curves of sand particles in Yeongil series showed the well sorted and differ from residuum soils derived from sand stone, but similar to dune soils(Haeri series). So it could be deducted from this study that "Yeongil" series are aeolian deposits derived from aeolian materials and have bisequum profile; the upper part depth of 40cm was recent cover sand, the horizon of 40~100cm depth was developed in Pleistocene epoch from the same materials.

• Journal of Korean Society for Atmospheric Environment
• /
• v.19 no.E1
• /
• pp.29-39
• /
• 2003

The 10-day interval basis measurements of precipitation samples at Yangyang, the rural and coastal area on the eastern coast of the Korea peninsula were accomplished for understanding the precipitation chemistry and the temporal variations of major ions September 1991 to February 1997. The precipitation was slightly acidic, and 37% of the samples in winter were pH less than 4.5. The concentrations of cations were found on the order $Na^+\;>\;{NH_4}^+\;>\;Ca^{2+}\;>\;Mg^{2+}\;>\;K^+$ and those of anions followed the pattern $Cl^-\;>\;{SO_4}^{2-}\;>\;{NO_3}^-$. Neglecting sea salt components, the major ions controlling precipitation chemistry were nss-${SO_4}^{2-}$ and ${NO_3}^-$ in anion and ${NH_4}^+$ and nss-$Ca^{2+}$ in cation. Concentrations of these ions were lower than those measured at urban sites in Korea, but were higher than those measured in Japan. Most of nss-${SO_4}^{2-}$ and ${NO_3}^-$ were neutralized by ammonia and calcium species, especially alkaline soil particles in spring and ammonia gas in other seasons. Considering also the annual value of ［nss -${SO_4}^{2-}$］/［${NO_3}^-$］ ratio of 2.62 and the neutralizing factors, ammonium sulphate compounds were dominant. Annual mean concentrations of these ions showed relatively small fluctuations, while larger seasonal variations were observed with higher levels in spring and winter. Precipitation amount, influence extent of acidic gases and alkaline particles long-range transported from China continent, and energy consumption pattern in each season might be able to explain this seasonal trend.sonal trend.

• Economic and Environmental Geology
• /
• v.30 no.5
• /
• pp.443-450
• /
• 1997

The main purpose of this study is to investigate mineralogical and chemical changes during natural weathering, and assess the mobility of major and trace elements. Yongwol power plant utilize anthracite coal which is mainly composed of illite, kaolinite, pyrophyllite and quartz in mineralogy. Coal and coal-derived fly ash samples were sampled by the electrostatic precipitator in Yongwol coal-fired power plant in Korea. Short term weathered fly ash were also collected in ash disposal mound, and two profile soil samples were taken from an ash near the power plant. Amorphous materials are the main component of the fly ash, and mullite, quartz, magnetite and heamatite are present in all coal-derived fly ash. In chemistry, Si and Al are the most abundant elements of the total content. The ash samples were fractionated into upper $90{\mu}m$ and under $45{\mu}m$ size. Finer particles show higher concentrations in metal contents including Co, Cr, Cu, Ni, V, Zn and Pb. Concentration of Zn and Pb are nearly 4 times higher concentration in the finer particles. For the profile samples, the concentrations of $SiO_2$, $Na_2O$, MgO and $K_2O$ generally show increasing trends with depth, whereas those of $Fe_2O_3$ and $TiO_2$ appear to decrease with depth. Content of MnO does not show any specific depth trend. For the trace elements, Co, Cu, Ni and V show increasing concentrations with depth.

• Journal of Korean Society for Atmospheric Environment
• /
• v.16 no.5
• /
• pp.453-467
• /
• 2000

The aim of this research is to collect and characterize fine particles (FPM:$\leq$2.5${\mu}{\textrm}{m}$) and coarse particles (CPM: 2.5~10${\mu}{\textrm}{m}$) using a low volume air sampler provided by the IAEA, at urban (Taejon) and rural area(Wonju) for a period of about two years(April 1996 to May 1998) and to promote a use of nuclear analytical techniques for air pollution studies. For the collection of airborne particulate matter (PM(sub)10), the Gent stacked filter unit sampler and polycarbonate membrane filters were employed. The concentration of trace elements in collected APM samples were determined byu instrumental Neutron Activation Analysis. For validation of the analytical data, internal quality control were implemented by using both the comparison of the analytical results of standard reference materials(NIST SRM 1648) and interlaboratory comparison for proficiency test (NAT-3). The standard uncertainty was less than 15% and Z-score of two samples were within $\pm$1. The monitoring of (PM(sub)10) mass concentration and elemental concentrations were carried out weekly. The average mass concentration of (PM(sub)10) in urban and rural areas were 59.2$\pm$36.5$\mu\textrm{g}$/㎥ and 41.4$\pm$23.7$\mu\textrm{g}$/㎥, respectively. To investigate the emission source, the enrichment factors were calculated for the fine and coarse particle fractions at two sites, respectively and these values were classified for anthropogenic and soil origin elements.

• Journal of Korean Society for Atmospheric Environment
• /
• v.21 no.E1
• /
• pp.23-35
• /
• 2005

Size distribution of particulate water-soluble ion components was measured at Gosan, Korea using a micro-orifice uniform deposit impactor (MOUDI). Sulfate, ammonium, and nitrate showed peaks in three size ranges; Sulfate and ammonium were of dominant species measured in the fine mode ($D_{p} < 1.8 {\mu}m$). One peak was observed in the condensation mode ($0.218\sim0.532{\mu}m$), and the other peak was obtained in the droplet mode ($0.532\sim1.8{\mu}m$). Considering the fact that the equivalent ratios of ammonium to sulfate ranged from 0.5 to 1.0 in these size ranges, it is inferred that they formed sufficiently neutralized compounds such as ($NH_{4})_{2}SO_{4} and (NH_{4})_{3}H(SO_{4})_{2}$ during the long-range transport of anthropogenic pollutants. On the other hand, nitrate was distributed mainly in the coarse mode ($3.1\sim6.2{\mu}m$) combined with soil and sea salt. Two sets of MOUDI samples were collected in each season. One sample was collected when the concentrations of criteria air pollutants were relatively high, but the other represented relatively clean air quality. The concentrations of sulfate and ammonium particles in droplet mode were the highest in winter and the lowest in summer. When the air quality was bad, the increase of nitrate was observed in the condensation mode ($0.218\sim0.282{\mu}m$). It thus suggests that the nitrate particles were produced through gas phase reaction of nitric acid with ammonia. Chloride depletion was remarkably high in summer due to the high temperature and relative humidity.

• Journal of Korean Society for Atmospheric Environment
• /
• v.17 no.2
• /
• pp.133-145
• /
• 2001

The receptor modeling is one of the statistical methods to achieve reasonable air pollution strategies. The pur-pose of this study was to survey the concentration variability oi inorganic elements and ionic species in the PM-10 particles, to qualitatively characterize emission sources by an advanced algorithm called positive matrix factoriza-tion(PMF) as a receptor model that can strictly provide results in every loading matrix. A total of 254 samples was collected by a PM-10 high volume air sampler from Mar. 1997 to Feb. 1998 in Kyung Hee University at Suwon Campus. Fourteen chemical species(Zn, Cu, Fe, Pb, Al, Mn, $Na^{+}$, NH$_4$+, $K^{+}$, $Mg^{2+}$, $Ca^{2+}$, $SO_4^{2-}$, $NO_{3}^{-}$, and $Cl^{-}$) were determined by AAS and IC methods. The study results showed that the average monthly concentration of PM-10 particles were 86.3$\mu\textrm{g}$/$\textrm{m}^3$ in March (maximum) and 28.5$\mu\textrm{g}$/$\textrm{m}^3$ in August(minimum), respectively. The concentrations of Na+, NH$_4$+, $K^{+}$ and $Cl^{-}$ in winter, $Mg^{2+}$, $Ca^{2+}$ and $NO_{3}^{-}$, in spring, and $SO_4^{2-}$ in summer showed the largest peak concentration for the respective season. Through and app-lication of a PMF program of Pm-10 concentration data of Suwon, 9 sources were qualitatively identified , such as incineration source, oil burning source, soil related source, open burning source automobile source, coal burning sources, secondary sulfate related source, and secondary nitrate related source.