• Proceedings of the Korean Geotechical Society Conference
• /
• 2009.09a
• /
• pp.133-144
• /
• 2009

Incheon Bridge, 18.4 km long sea-crossing bridge, will be opened to the traffic in October 2009 and this will be the new landmark of the gearing up north-east Asia as well as the largest & longest bridge of Korea. Incheon Bridge is the integrated set of several special featured bridges including a magnificent cable-stayed girder bridge which has a main span of 800 m width to cross the navigation channel in and out of the Port of Incheon. Incheon Bridge is making an epoch of long-span bridge designs thanks to the fully application of the AASHTO LRFD (load & resistance factor design) to both the superstructures and the substructures. A state-of-the-art of the geotechnologies which were applied to the Incheon Bridge construction project is introduced. The most Large-diameter drilled shafts were penetrated into the bedrock to support the colossal superstructures. The bearing capacity and deformational characteristics of the foundations were verified through the world's largest static pile load test. 8 full-scale pilot piles were tested in both offshore site and onshore area prior to the commencement of constructions. Compressible load beyond 30,000 tonf pressed a single 3 m diameter foundation pile by means of bi-directional loading method including the Osterberg cell techniques. Detailed site investigation to characterize the subsurface properties had been carried out. Geotextile tubes, tied sheet pile walls, and trestles were utilized to overcome the very large tidal difference between ebb and flow at the foreshore site. 44 circular-cell type dolphins surround the piers near the navigation channel to protect the bridge against the collision with aberrant vessels. Each dolphin structure consists of the flat sheet piled wall and infilled aggregates to absorb the collision impact. Geo-centrifugal tests were performed to evaluate the behavior of the dolphin in the seabed and to verify the numerical model for the design. Rip-rap embankments on the seabed are expected to prevent the scouring of the foundation. Prefabricated vertical drains, sand compaction piles, deep cement mixings, horizontal natural-fiber drains, and other subsidiary methods were used to improve the soft ground for the site of abutments, toll plazas, and access roads. Light-weight backfill using EPS blocks helps to reduce the earth pressure behind the abutment on the soft ground. Some kinds of reinforced earth like as MSE using geosynthetics were utilized for the ring wall of the abutment. Soil steel bridges made of corrugated steel plates and engineered backfills were constructed for the open-cut tunnel and the culvert. Diverse experiences of advanced designs and constructions from the Incheon Bridge project have been propagated by relevant engineers and it is strongly expected that significant achievements in geotechnical engineering through this project will contribute to the national development of the longspan bridge technologies remarkably.

• Korean Journal of Plant Resources
• /
• v.19 no.4
• /
• pp.447-458
• /
• 2006

The resource plants at the Manduksan and Mireukbong was listed 550 taxa: 107 families, 339 genera, 481 species, 1 subspecies, 65 varieties and 3 forms. Among 550 taxa listed was confirmed 323 taxa of edible plants (58.7%), 384 taxa of medicinal plants (69.8%), 267 taxa of ornamental plants (48.5%) and 268 taxa of the others (48.7%). Based on the list of the rare plants by the Forest Research Institute, 4 taxa were recorded in the studied areas; Lilium distichum (Preservation priority order: No. 159), Tricyrtis dilatata (No. 97), Aristolochia contorta (No. 151), Prunus yedoensis (No. 110) and based on the list of Korean endemic plants, 11 taxa were recorded; Cephalotaxus koreana, Carex okamotoi, Lilium amabile, Populus tomentiglandulosa, Salix purpurea var. japonica, Pseudostellaria multiflora, Prunus yedoensis, Forsythia koreana, Paulownia coreana, Weigela subsessilis, Aster koraiensis. Specific plant species by floral region were total 30 taxa; Prunus yedoensis in class V, Wistaria floribunda in class IV, 3 taxa (Spiraea salicifolia, Acer palmatum, Asperula lasiantha) in class III, 3 taxa (Potentilla dickinsii, Viola tokubuchiana var. takedana, Caryopteris incana) in class II, 22 taxa (Pinus koraiensis, Hosta capitata, Chloranthus japonicus, Salix glandulosa, Juglans mandshurica, etc.) in class I. This site needs urgent countermeasures, because there have increased many man-made damages like planting exotic plants, picking wild plants and soil compaction induced by human trampling.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.27 no.6
• /
• pp.733-739
• /
• 2009

Recently it is being increased rapidly to install magnetic marker and RFID tag on the underground utility lines before backfilling to ensure effective it's management. However, due to changes an attitude and damages of sensors. By pressure and vibration during soil compacting, detecting rate is significantly reduced as well as it allows to use only one line of various pipes since it has an unique frequency. Also it is required too long time to reach to target point with an non-accurate navigational GPS receiver and hard to update existing data base with a manual input of new data in the field. To improve these problems, the researcher developed the field management system that apply with ball typed self-levelling marker which is free from the changes of attitude for sensors during compaction as well as has various radio frequency applicable to many kind of pipes and ensure fast positioning to target point using an incorporated system with PDA based DGPS receiver which allows loading a field GIS software and RFID detector. Further, it provides with viewing all of RFID data on the DGPS receiver screen directly and also input new data to existing data base in the field automatically.

• Journal of Korea Water Resources Association
• /
• v.52 no.2
• /
• pp.133-139
• /
• 2019

In this study, the degree of scouring according to the bed material according to the flow rate and the relationship between the flow velocity and the bed scouring were investigated in order to examine the operability of the revetment and embankment. The materials used in the experiment were sand and loess as materials used in the embankment. We measured the scouring of the material according to the change of the flow velocity by using the indoor high flow velocity experiment device and verified the flow rate. In this way, The purpose of this study was to compare and analyze changes in material before and after scouring, and compare basal scouring evaluation by bed material with high flow velocity. In case of sand, the cohesive force is very weak, so more than 40% of the material is lost even at less than 1.0 m/s. In the case of loess, less than 6% of the bed material is lost at more than 2 m/s. The reason why the material was lost was that the cohesion was so strong that the material was dried after the compaction and cracked. As a result, the material was lost from the part where the dry crack occurred. In this study, the composition and loss of bed materials were evaluated.

• Journal of the Korean Geotechnical Society
• /
• v.24 no.6
• /
• pp.57-67
• /
• 2008

Two test methods, nonrepetitive plate loading test (NPLT) and repetitive plate loading test (RPLT) are being used to control the quality of compaction through the evaluation of the stiffness of subgrade soils in the Korea railway industry. Subgrade reaction modulus ($k_{30}$) from the NPLT and strain modulus ($E_v$) from the RPLT are the index values to check them. The methods have similar aspects, but they differ in the modulus evaluation method, the numbers of loading stage, termination procedures, etc. This paper analyses the differences of the two test methods and evaluates the relationship between subgrade reaction modulus and strain modulus. In order to develop the relationship, total 22 tests were performed including the NPLT and the RPLT at the 6 original grounds, and 5 upper or lower subgrades in Kyungbu High Speed Railway II stage construction sites. According to the soil conditions, the relationship between subgrade reaction modulus and strain modulus was proposed with corrections by considering strain states, mean confining pressures, and Poisson's ratio.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.29 no.6C
• /
• pp.251-258
• /
• 2009

In this study, the optimum design conditions for embankment construction on soft clay layer improved by soil compaction pile (SCP) are discussed by comparing the practical design method to the reliability design which is based on the loss function and advanced first order second moment (AFOSM) method. The results are summarized as follows; 1) the relationship between safety factor and failure probability becomes heavy exponentially, failure probability decreases rapidly till 1% approximately until safety factor is smaller than 1.2 and after then, failure probability decrease gradually along the increase of the safety factor. The design safety factor of 1.2 may be the critical value that has been established on considering both relationships appropriately, 2) the safety factor of 1.15 at the minimum expected total cost is a little smaller than the design safety factor of 1.2 and the failure probability is about 1%, 3) the sensitivities of the ratio of stress share and the internal friction angle of sand is larger than the variables related the undrained shear strength of soft layer. This result means that the distribution characteristic of n and ${\phi}$ influences on the stability analysis considerably and they should be considered necessarily on stability analysis of embankment on soft layer improved by SCP, 4) new failure points of the input variables at the design safety factor of 1.2(below failure probability of 0.1~0.3%) is far 1~2 times of standard deviation from the initial design values of themselves.

• Proceedings of the Korean Society of Crop Science Conference
• /
• 2023.04a
• /
• pp.105-105
• /
• 2023

Heavy metals, including lead (Pb) toxicity, are increasing in soil and are considered toxic in small amounts. Pb contamination is mainly caused by industrialization - smelting, mining. Agricultural practices - sewage sludge, pests and urban practices - lead paint. It can seriously damage and threaten crop growth. Pb can adversely affect plant growth and development by affecting the photosystem, cell membrane integrity, and excessive production of reactive oxygen species (ROS) such as hydrogen peroxide (H₂O₂)andsuperoxide(O₂.-). NO is produced via enzymatic and non-enzymatic antioxidants to scavenge ROS and lipid peroxidation substrates in terms of protecting cells from oxidative damage. Thus, NO improves ion homeostasis and confers resistance to metal stress. Our results here suggest that exogenous NO may aid in better growth under lead stress. These enhancements may be aided by NO's ability in sensing, signaling and stress tolerance in plants under heavy metal stress in combination with lead stress. Our results show that GSNO has a positive effect on soybean seedling growth in response to axillary pressure and that NO supplementation helps to reduce chlorophyll maturation and relative water content in leaves and roots following strong burst under lead stress. GSNO supplementation (200 µM and 100 µM) reduced compaction and approximated oxidative damage of MDA, proline and H₂O₂. Under plant tension, a distorted appearance was found in the relief of oxidative damage by ROS scavenging by GSNO application. In summary, modulation of these NO, PCS and prolongation of metal past reversing GSNO application confirms the detoxification of ROS induced by toxic metal rates in soybean. In summary, these NO, PCS and metal traditionally sustained rates of reverse GSNO application confirm the detoxification of ROS induced by toxic metal rates in soybean.

• Journal of the Korean Institute of Landscape Architecture
• /
• v.37 no.6
• /
• pp.12-18
• /
• 2010

This study was carried out in order to propose a planning index for improved school forests in Gyeonggido. For the purpose of this study we selected 42 out of 75 school forests established during 2005 in Gyeonggido. All 42 school forests were surveyed and analyzed by frequency, cross tabulation, and group average analysis with SPSS 12.0 version. The present condition of the school forests was analyzed with in conjunction with items such as the surrounding environment, centralization, and locational characteristics as nominal points. Other items: trees, shrubs, pavement, fruit trees, transplantation, evergreen trees, and recreation facility content percentage were analyzed as a proportion point. After reviewing the literature and analyzing the present condition of school forests, we constructed a conceptual framework and formulated a hypothesis for this research. Data were obtained through a questionnaire, given to 98 students majoring in landscape architecture at Hankyong University in 2007. Results showed that the primary variables for tree health were soil compaction and the depth of soil filling. They were the most serious factors that deteriorate the health of trees. Based on the relationship between tree health and growing conditions, trees inside the school forest should be managed to provide more growing space and less abuse. The minimum area for trees inside the school forest for good growth conditions should be within the drip lines. We have found that the minimum percentage of tree content is 0.13, which means that more than 130 trees need to be planted over $1,000m^2$ green space. More than 3,580 shrubs need to be planted over $1,000m^2$ green space. The pavement area should be controlled to less than 19% of the total size of the school forest area. Finally, more than 39 trees out of 100 trees planted should be evergreen. The research results suggest that the construction planning index of Gyeonggido school forest be recommended in the planning and development process of the construction project carried out every year.

• Horticultural Science & Technology
• /
• v.31 no.5
• /
• pp.558-564
• /
• 2013

The objective of this research was to secure the fundamental information in changes of soil physical properties as influenced by the compaction of root media during container filling. Three root media were formulated by blending peatmoss (PM) with expanded rice hull (PM + ERH, 8:2, v/v), carbonized rice hull (PM + CRH, 6:4) and ground and aged pine bark (PM + GAPB, 8:2). Based on the optimum bulk density, the amount of root media filled into 6.0, 7.5, 8.5, 10.5 and 12.5 cm were adjusted to 90, 100, 110, 120, and 130%, then the changes in total porosity (TP), container capacity (CC), and air-filled porosity (AFP) were measured. The TP decreased significantly as the packing amount of three root media were elevated in all sizes of container. The TP did not show significant differences among the root media in small sizes of containers, but showed significant differences when sizes of containers became larger. As packing amount of three root media were elevated, the CCs in all sizes of containers were decreased. The PM + CRH had the lowest CC among three root media in containers smaller than 8.5 cm, but had the highest CC in those larger than 10.5 cm. These results indicated that the decreases in CC were influenced by the sizes of containers as well as kinds of root media. The elevation of packing amount in three root media diminished significantly the AFP. The AFP in PM + GAPB medium was two times as high as those of PM + ERH or PM + CRH when equal packing densities were applied in all sizes of containers. As the container sizes became larger in three root media, the extents in decreasing of CC were distinct than those of AFP. Above results indicate that elevation in packing amount of three root media decreased significantly the TP, CC and AFP, but these were influenced differently by sizes of containers and kinds of root media. The results would be useful for expectation in the changes of physical properties in various sizes of containers filled with peatmoss based root media.

• Korean Journal of Soil Science and Fertilizer
• /
• v.18 no.4
• /
• pp.325-335
• /
• 1985

Biogas production from agricultural wastes were summarized as follows: 1. Biogas Generation Characteristics of Various Manures and Residues a. Gas yield from crop residues like rice straw, rice hull, corn stalk and coconut husk can be improved by addition of animal manures. b. Gas yield from coconut husk can be improved through aerobic fermentation for at least one week before loading in the digester. c. Gas yield from fresh rice straw is better than from pre-fermented one, whether alone or in combination with animal manures. d. Initial study has shown that fresh azolla can be substituted for animal manures in manurerice straw combinations and gas yield derived based on unit volatile solids loaded is actually better than for manure-residue combinations. e. Gas production is highly sensitive to substrate pH and becomes almost nil at a pH of below 6. 2. Effect of ambient conditions and other factors on biogas production in a house hold-size digester. a. Results showed that compaction of rice straw in straw-manure combination can reduce gas yield compared with loosely mixed straw. b. The effective gas production period extended to 70 days using freshly threshed rice straw and fresh cattle manure as feed material. c. Underground and above ground digesters with shade have relatively more stable substrate temperature than aboveground exposed digesters. This relative temperature instability may likely be the reason for lower gas yield for the exposed aboveground digester loaded with loose straw-cattle manure substrate, compared with the underground digester with the same substrate. 3. Economic Analysis a. Based on prevailing costs of fuel, materials, and labor in the Philippines, biogas produced from the household size system is cheaper than either LPG or kerosene. b. If other benefits like organic fertilizer, pollution control and convenience are considered, biogas will surely be the best alternative fuel source.