• International Journal of Aeronautical and Space Sciences
• /
• v.9 no.2
• /
• pp.121-128
• /
• 2008

Modularized GPS software defined radio (SDR) has many advantages of applying and modifying algorithm. Hardware based GPS receiver uses many hardware parts (such as RF front, correlators, CPU and other peripherals) that process tracked signal and navigation data to calculate user position, while SDR uses software modules, which run on general purpose CPU platform or embedded DSP. SDR does not have to change hardware part and is not limited by hardware capability when new processing algorithm is applied. The weakness of SDR is that software correlation takes lots of processing time. However, in these days the evolution of processing power of MPU and DSP leads the competitiveness of SDR against the hardware GPS receiver. This paper shows a study of modulization of GPS software platform and it presents development of the GNSS software platform using MATLAB Simulink™. We focus on post processing SDR platform which is usually adapted in research area. The main functions of SDR are GPS signal acquisition, signal tracking, decoding navigation data and calculating stand alone user position from stored data that was down converted and sampled intermediate frequency (IF) data. Each module of SDR platform is categorized by function for applicability for applying for other frequency and GPS signal easily. The developed software platform is tested using stored data which is down-converted and sampled IF data file. The test results present that the software platform calculates user position properly.

• International Journal of Control, Automation, and Systems
• /
• v.4 no.3
• /
• pp.344-350
• /
• 2006

The software GPS receivers based on the SDR technology provide the ability to easily adapt the other signal processing algorithms without changing or modifying the hardware of the GPS receiver. However, it is difficult to implement the software GPS receivers using a commercial processor because of the heavy computational burden for processing the GPS signals in real-time. This paper proposes an efficient GPS signal processing scheme to reduce the computational burden for processing the GPS signals in the software GPS receiver, which uses a fundamental notion compressing the replica signals and the encoded look-up table method to generate correlation values between GPS signals and replica signals. In this paper, it is explained that the computational burden of the proposed scheme is much smaller than that of the typical GPS signal processing scheme. Finally, the processing time of the proposed scheme is compared with that of the typical scheme, and the improvement in the aspect of the computational burden is also shown.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• v.2
• /
• pp.347-352
• /
• 2006

Narrowband interference can severely degrade the performance of GPS receivers. Detecting the presence of interference and then characterizing it can lead to its removal. Receivers can be reconfigured to focus on other signals or satellites that are less vulnerable to that interference at that moment. Using hardware reconfigurability of FPGA receivers and characterizing the effect of narrowband interference on the GNSS signal quality lead us to a new RFI mitigation technique in which the highest quality and less vulnerable signal can be chosen at each moment. In the previous work [1], the post processing capability of a software GPS receiver, has been used to detect and characterize the CW interference. This is achieved by passing the GPS signal and the interference through the correlator. Then, using the conventional definition of C/No as the squared mean of the correlator output divided by its variance, the actual C/No for each satellite is calculated. In this work, first the 'Exclusion zone' for each satellite signal has been defined and then by using some experiments the effects of different parameters like signal power, jamming power and the environmental noise power on the Exclusion zone have been analyzed. By monitoring the Doppler frequency of each satellite and using the actual C/No of each satellite using the traditional definition of C/No and actual data from a software GPS receiver, the decision to reconfigure the receiver to other signal can be made.

• Journal of Positioning, Navigation, and Timing
• /
• v.10 no.4
• /
• pp.315-333
• /
• 2021

Due to the Global Navigation Satellite System (GNSS) modernization, recently launched GNSS satellites transmit signals at various frequency bands such as L1, L2 and L5. Considering the Korean Positioning System (KPS) signal and other GNSS augmentation signals in the future, there is a high probability of applying more complex communication techniques to the new GNSS signals. For the reason, GNSS receivers based on flexible Software Defined Radio (SDR) concept needs to be developed to evaluate various experimental communication techniques by accessing each signal processing module in detail. This paper proposes a novel SDR-based A-GNSS receiver capable of processing multi-GNSS/RNSS signals at multi-frequency bands. Due to the modular structure, the proposed receiver has high flexibility and expandability. For real-time implementation, A-GNSS server software is designed to provide immediate delivery of satellite ephemeris data on demand. Due to the sampling bandwidth limitation of RF front-ends, multiple SDRs are considered to process the multi-GNSS/RNSS multi-frequency signals simultaneously. To avoid the overflow problem of sampled RF data, an efficient memory buffer management strategy was considered. To collect and process the multi-GNSS/RNSS multi-frequency signals in real-time, the proposed SDR A-GNSS receiver utilizes multiple threads implemented on a CPU and multiple NVIDIA CUDA GPGPUs for parallel processing. To evaluate the performance of the proposed SDR A-GNSS receiver, several experiments were performed with field collected data. By the experiments, it was shown that A-GNSS requirements can be satisfied sufficiently utilizing only milliseconds samples. The continuous signal tracking performance was also confirmed with the hundreds of milliseconds data for multi-GNSS/RNSS multi-frequency signals and with the ten-seconds data for multi-GNSS/RNSS single-frequency signals.

• Journal of Positioning, Navigation, and Timing
• /
• v.3 no.3
• /
• pp.91-97
• /
• 2014

A direct RF sampling method refers to a technique that directly converts a passband signal to an intermediate band or a baseband without using a mixer. This method is less complicated than an existing RF receiver because a mixer is not used. It uses digital processing after sampling, and thus can flexibly process signals in a number of bands using software. In this process, it is important to select an appropriate sampling frequency so that a number of signals can be converted to an intermediate band that is easy to process. In this study, going beyond previously studied direct RF sampling frequency selection methods, conditions that need to be additionally considered during receiver design were examined, and the structure of a direct RF sampling receiver that satisfies these conditions was suggested.

• ETRI Journal
• /
• v.32 no.2
• /
• pp.214-221
• /
• 2010

Radio frequency (RF) subsampling can be used by radio receivers to directly down-convert and digitize RF signals. A goal of a cognitive radio/software defined ratio (CR/SDR) receiver design is to place the analog-to-digital converter (ADC) as near the antenna as possible. Based on this, a band-pass sampling (BPS) frontend for CR/SDR is proposed and verified. We present a receiver architecture based second-order BPS and signal processing techniques for a digital RF frontend. This paper is focused on the benefits of the second-order BPS architecture in spectrum sensing over a wide frequency band range and in multiband receiving without modification of the RF hardware. Methods to manipulate the spectra are described, and reconstruction filter designs are provided. On the basis of this concept, second-order BPS frontends for CR/SDR systems are designed and verified using a hardware platform.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• v.2
• /
• pp.385-390
• /
• 2006

This paper examines the sampling and jitter specifications and considerations for Global Navigation Satellite Systems (GNSS) software receivers. Software radio (SWR) technologies are being used in the implementation of communication receivers in general and GNSS receivers in particular. With the advent of new GPS signals, and a range of new Galileo and GLONASS signals soon becoming available, GNSS is an application where SWR and software-defined radio (SDR) are likely to have an impact. The sampling process is critical for SWR receivers, where it occurs as close to the antenna as possible. One way to achieve this is by BandPass Sampling (BPS), which is an undersampling technique that exploits aliasing to perform downconversion. BPS enables removal of the IF stage in the radio receiver. The sampling frequency is a very important factor since it influences both receiver performance and implementation efficiency. However, the design of BPS can result in degradation of Signal-to-Noise Ratio (SNR) due to the out-of-band noise being aliased. Important to the specification of both the ADC and its clocking Phase- Locked Loop (PLL) is jitter. Contributing to the system jitter are the aperture jitter of the sample-and-hold switch at the input of ADC and the sampling-clock jitter. Aperture jitter effects have usually been modeled as additive noise, based on a sinusoidal input signal, and limits the achievable Signal-to-Noise Ratio (SNR). Jitter in the sampled signal has several sources: phase noise in the Voltage-Controlled Oscillator (VCO) within the sampling PLL, jitter introduced by variations in the period of the frequency divider used in the sampling PLL and cross-talk from the lock line running parallel to signal lines. Jitter in the sampling process directly acts to degrade the noise floor and selectivity of receiver. Choosing an appropriate VCO for a SWR system is not as simple as finding one with right oscillator frequency. Similarly, it is important to specify the right jitter performance for the ADC. In this paper, the allowable sampling frequencies are calculated and analyzed for the multiple frequency BPS software radio GNSS receivers. The SNR degradation due to jitter in a BPSK system is calculated and required jitter standard deviation allowable for each GNSS band of interest is evaluated. Furthermore, in this paper we have investigated the sources of jitter and a basic jitter budget is calculated that could assist in the design of multiple frequency SWR GNSS receivers. We examine different ADCs and PLLs available in the market and compare known performance with the calculated budget. The results obtained are therefore directly applicable to SWR GNSS receiver design.

• ETRI Journal
• /
• v.30 no.1
• /
• pp.141-151
• /
• 2008

In this paper, we introduce a new verification platform with ARM- and DSP-based multiprocessor architecture. Its simple communication interface with a crossbar switch architecture is suitable for a heterogeneous multiprocessor platform. The platform is used to verify the function and performance of a DVB-T baseband receiver using hardware and software partitioning techniques with a seamless hardware/software co-verification tool. We present a dual-processor platform with an ARM926 and a Teak DSP, but it cannot satisfy the standard specification of EN 300 744 of DVB-T ETSI. Therefore, we propose a new multiprocessor strategy with an ARM926 and three Teak DSPs synchronized at 166 MHz to satisfy the required specification of DVB-T.

• Journal of Institute of Control, Robotics and Systems
• /
• v.15 no.6
• /
• pp.649-654
• /
• 2009

In this paper, an frequency tracking algorithm for weak signal tracking is proposed. The proposed frequency tracking algorithm uses a FMS (Fast Minus Slow) discriminator for frequency error estimation. This frequency tracking algorithm shows good frequency estimation performance under weak signal condition and is a computationally efficient for embedded software GNSS receiver. The software GNSS receiver implementing the proposed weak signal tracking algorithms could track GPS signal down to - 159dBm signal strength in the signal generator test and real GPS signal under dense urban condition.

• 제어로봇시스템학회:학술대회논문집
• /
• 2001.10a
• /
• pp.114.4-114
• /
• 2001

Recently, variety services are more and more developed due to supply of PDA, cellular phone, and etc. Also, a services based on location information are very helpful in traffic, shopping, and emergency. Thus the user position is positively necessary for these services. One of the latest applications in GPS is the E911 call service for wireless phones. In this case, current GPS Navigation accuracy meets the FCC requirements but the hardware size and power consumption of GPS is issued for implementation. And, some case of applications need to snapshot location solution with fast TTFF(Time-To-Fist-Fix) than continuous location solution. The software GPS receiver could be the solution ...