• International Journal of Naval Architecture and Ocean Engineering
• /
• v.11 no.1
• /
• pp.274-284
• /
• 2019

The control architectures of Chuan Suo (CS) deep submergence rescue vehicle are introduced. The hardware and software architectures are also discussed. The hardware part adopts a distributed control system composed of surface and underwater nodes. A computer is used as a surface control machine. Underwater equipment is based on a multi-board-embedded industrial computer with PC104 BUS, which contains IO, A/D, D/A, eight-channel serial, and power boards. The hardware and software parts complete data transmission through optical fibers. The software part involves an IPC of embedded Vxworks real-time operating system, upon which the operation of I/O, A/D, and D/A boards and serial ports is based on; this setup improves the real-time manipulation. The information flow is controlled by the software part, and the thrust distribution is introduced. A submergence vehicle heeling control method based on ballast water tank regulation is introduced to meet the special heeling requirements of the submergence rescue vehicle during docking. Finally, the feasibility and reliability of the entire system are verified by a pool test.

• The Transactions of the Korean Institute of Electrical Engineers A
• /
• v.50 no.3
• /
• pp.131-139
• /
• 2001

As increasing the accident of Distribution Transformer (DT), we need to manage them efficiently. In this paper, we discusses with the possibility of the diagnostic technique for distribution transformer using relative ageing rate calculation in this paper. The relative ageing rate of the DT could be calculated from the measured top oil temperature, ambient temperature and load current. In order on apply the proposed diagnostic technique we developed an on line Monitoring and Diagnostic System (MDS) which has hardware and software part. Diagnostic device is developed to measure the state information of DT and to send them with R/F(radio frequency) communication. Host computer monitors and saves the receive data. The database is constructed from the data of distributed DT and it is used for estimating loss-of-life in the MDS.

• Proceedings of the Korea Committee for Ocean Resources and Engineering Conference
• /
• 2000.10a
• /
• pp.84-89
• /
• 2000

Thermal simulation of typical stack-type and newly proposed planar-type micro-gas sensors were studied by FEM method. The thermal analyses for the proposed planar structure including temperatur distribution over the sensing layer and power consumption of the heater were carried using finite element method by computer simulation and well compared with those of typical stack-type micro-gas sensor. The thermal properties of the microsensor from thermal simulation were compared with those of a actual device to investigate the acceptability of the computer simulation.

• Journal of Biomedical Engineering Research
• /
• v.9 no.1
• /
• pp.31-36
• /
• 1988

A personal computer-based brain map is described which will display a gray scale maps showing the distribution of signals derived from the electrical activity of the brain such as EEG or EP This topographic brain mapping system has a flexibility which describe the electrode number and placement mapping onto any shaped space and generate a brain maps by incoorporated the data acquisition and processing software with conventional EEG machine.

• The Journal of Asian Finance, Economics and Business
• /
• v.9 no.6
• /
• pp.303-312
• /
• 2022

Nowadays, omnichannel is a new kind of e-commerce channel. Many retailers invest in this channel to maximize customers' benefits as well as increase competitive advantage and business performance. To operate this channel effectively, the role of IT competence is very important. With the flexibility and integration of IT competence in omnichannel, retailers can optimize service quality and bring customer benefits that are outstanding in comparison with the traditional channel. Because of this significance, this research was carried out to evaluate the effects of IT competence on the business performance of retailers in Vietnam's omnichannel environment through the mediating role of customer value creation and competitive advantage. A quantitative research method is used through a survey with 200 managers working in retail companies operating omnichannel in Vietnam. After collecting data, PLS-SEM software is used to analyze the relationship among these above factors in omnichannel. The results prove that there are positive effects of IT competence on other elements in the research model. All direct and indirect effects are valuable when bootstrapping. Based on the results, some managerial implications are given to managers of retail companies using omnichannel to improve customer values and increase competitive advantage and business performance in the Vietnam context.

• Journal of Information Processing Systems
• /
• v.13 no.6
• /
• pp.1602-1612
• /
• 2017

Since rapidly disseminating of Internet of Things (IoT) as the new communication paradigm, a number of studies for various applications is being carried out. Especially, interest in the smart medical system is rising. In the smart medical system, a number of medical devices are distributed in popular area such as station and medical center, and this high density of medical device distribution can cause serious performance degradation of communication, referred to as the coexistence problem. When coexistence problem occurs in smart medical system, reliable transmitting of patient's biological information may not be guaranteed and patient's life can be jeopardized. Therefore, coexistence problem in smart medical system should be resolved. In this paper, we propose a distributed coexistence mitigation scheme for IoT-based smart medical system which can dynamically avoid interference in coexistence situation and can guarantee reliable communication. To evaluate the performance of the proposed scheme, we perform extensive simulations by comparing with IEEE 802.15.4 MAC protocol which is a traditional low-power communication technology.

• Journal of Korea Multimedia Society
• /
• v.8 no.6
• /
• pp.744-752
• /
• 2005

When the multiple video sources are transmitted together through the channel of fixed bandwidth, an efficient picture quality control is necessary. This paper presents a joint picture quality control method to satisfy the user requirement by priority among the video sources. The better picture quality is assigned to the source of higher priority compared to lower priority. We obtain the bitrate for each source to have a required distortion level among the sources by using an approximate distortion-bitrate model for simple implementation. It is shown by simulation that the proposed bandwidth allocation method can keep almost the user-required picture quality among the sources in comparison to an independent bandwidth allocation method.

• Journal of the Korean Society of Systems Engineering
• /
• v.13 no.1
• /
• pp.33-39
• /
• 2017

This paper describes the system engineering approach for the heat transfer analysis of plus7 fuel rod for APR1400 using, a commercial software, ANSYS. The fuel rod is composed of fuel pellets, fill gas, end caps, plenum spring and cladding. The heat is transferred from the pellet outward by conduction through the pellet, fill gas and cladding and further by convection from the cladding surface to the coolant in the flow channel. The goal of this paper is to demonstrate the temperature and heat flux change from the fuel centerline to the cladding surface when having maximum fuel centerline temperature at 100% power. This phenomenon is modelled using the ANSYS FEM code and analyzed for steady state temperature distribution across the fuel pellet and clad and the results were compared to the standard values given in APR1400 SSAR. Specifically the applicability of commercial software in the evaluation of nuclear fuel temperature distribution has been accounted. It is note that special codes have been used for fuel rod mechanical analysis which calculates interrelated effects of temperature, pressure, cladding elastic and plastic behavior, fission gas release, and fuel densification and swelling under the time-varying irradiation conditions. To satisfactorily meet this objective we apply system engineering methodologies to formulate the process and allow for verification and validation of the results acquired. The close proximity of the results obtained validated the accuracy of the FEM analysis of the 2D axisymmetric model and 3D model. This result demonstrated the validity of commercial software instead of proprietary in-house code that is more costly to develop and maintain.

• International Journal of Fluid Machinery and Systems
• /
• v.10 no.2
• /
• pp.138-145
• /
• 2017

The problem of non-uniform inflow exists in many practical engineering applications, such as the elbow suction pipe of waterjet pump and, the channel head of steam generator which is directly connect with reactor coolant pump. Generally, pumps are identical designs and are selected based on performance under uniform inflow with the straight pipe, but actually non-uniform suction flow is induced by upstream equipment. In this paper, CFD approach was employed to analyze unsteady hydrodynamic characteristics of reactor coolant pumps with different inflows. The Reynolds-averaged Naiver-Stokes equations with the $k-{\varepsilon}$ turbulence model were solved by the computational fluid dynamics software CFX to conduct the steady and unsteady numerical simulation. The numerical results of the straight pipe and channel head were validated with experimental data for the heads at different flow coefficients. In the nominal flow rate, the head of the pump with the channel head decreases by 1.19% when compared to the straight pipe. The complicated structure of channel head induces the inlet flow non-uniform. The non-uniformity of the inflow induces the difference of vorticity distribution at the outlet of the pump. The variation law of blade to blade velocity at different flow rate and the difference of blade to blade velocity with different inflow are researched. The effects of non-uniform inflow on radial forces are absolutely different from the uniform inflow. For the radial forces at the frequency $f_R$, the corresponding amplitude of channel head are higher than the straight pipe at $1.0{\Phi}_d$ and $1.2{\Phi}_d$ flow rates, and the corresponding amplitude of channel head are lower than the straight pipe at $0.8{\Phi}_d$ flow rates.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.28 no.5A
• /
• pp.294-304
• /
• 2003

For an efficient software download in cellular CDMA systems, session admission control based on area (SACA) is presented. In the SACA scheme, the base station only allows mobile terminal to start session when the mobile locates near the base station of a cell. A mobile that is located near cell center can request software download session, but the mobile that is far away from the center can request session only after arriving near the cell center. Session duration time follows exponential and Pareto distribution. Performance is analyzed in terms of handoff rate, mean channel holding time, session blocking probability and handoff forced termination probability. As analysis results, handoff rate between cells in the proposed scheme is reduced to 30 ~ 250 % compared to conventional scheme, according to traffic characteristics such as terminal speed, session duration time and the size of the allowable zone area in a cell for the start of the session. And new session blocking probability slightly decreases to 5 ~ 20 %, but handoff session forced termination probability drastically decreases to 35 ~ 220 %.