• 한국식품영양학회지
• /
• 제14권5호
• /
• pp.385-390
• /
• 2001

1. 비가열 시료인 a와 b가 PE의 활성은 저장 둘째 주에 급격히 증가하다가 감소하였고, 가열 시료인 c 는 저장 넷째 주에 증가하다가 감소하였고, 병행 열처리와 trehalose 처리 시료는 저장 끝까지도 증가하였다. 2. PG의 활성은 비가열 시료인 a와 b는 저장 둘째 주부터 감소하다 저장 끝에는 증가하였고, 가열 시료인 c와 d는 저장 기간 동안 변화가 거의 없었다. 3. POD의 활성은 비가열 시료인 a와 b는 저장 둘째 주에 증가하다 감소하였고, 가열 시료인 c는 둘째 주에 약간씩 감소하였고, 병용 열처리하고 trehalose 처리군은 감소하였다. 4. 관능검사 결과 시료 a. b, d는 아작함과 기호도가 전 저장 기간동안 높았고, 시료 c는 갈색과 신맛의 증가로 기호도가 낮았다 저장기간에 따라서는 2주차에는 아작함과 형태가 좋았으나 4주 6주로 가면서 아작함과 기호도의 값이 감소하였다. 그리고 각 시료별 기호도에 가장 영향을 주는 항목은 아작함이었고 시료 c는 갈색, 맛, 조직감 등에서 음의 관계를 나타냈다.

• 한국식생활문화학회지
• /
• 제35권6호
• /
• pp.582-589
• /
• 2020

This study was carried out to determine the optimum temperature of the jicama pickle solution by evaluating physicochemical and sensory characteristics at various temperatures. The soaking solution of the jicama pickle was prepared at different temperatures (95, 75, 50, and 25℃). During storage, the titratable acidity, Brix, and the salinity of the jicama pickles increased, and these values increased with increasing temperature of the soaking solution. The higher the temperature of the soaking solution, the lower the L and b values. In all samples, the hardness increased rapidly until the 5th day of storage, and then gradually decreased. During storage, the jicama pickles showed a high tendency to harden at soaking solution temperatures of 75 and 95℃. Sensory evaluation indicated that the taste, flavor, crispness, and overall preference of the jicama pickle were higher at a soaking solution temperature of 75℃ and above. The higher the temperature of the soaking solution, the higher the acceptability. Based on these results, we conclude that soaking solution temperature of 75°¦95℃ in the manufacture of jicama pickles had a positive effect on the reduction in tissue softening and the sensory properties of the jicama pickle.

• 한국식품영양학회지
• /
• 제5권2호
• /
• pp.163-169
• /
• 1992

The changes in the various chemical compositions and textural properties of salted vegetables during salting and fermentation were reviewed with 25 papers published from 1981 to 1991 The changes in the texture of vegetables were largely affected by the properties of pectic substances, and additional factors such as salt type, salt concentration, salting time, temperature, preheating treatment, enzyme, salt mixtures, salt-fermented fish and garlic contents, were concerned complexly.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2003년도 춘계학술대회논문집
• /
• pp.295-298
• /
• 2003

High temperature deformation behavior of a Ti-Al intermetallic compound has been investigated. Specimens with a near gamma and a lamella structures were obtained by performing heat treatment at 1200 and 1330$^{\circ}C$, respectively, for 24 hr and stabilized at 900$^{\circ}C$ for 4 hr followed by air cooling. A series of load relaxation tests has been conducted on these samples at temperatures ranging from 850 to 950$^{\circ}C$ to construct flow curves in the strain rate range from 10$\^$-6//s to 10$\^$-3//s. Strain hardening was observed even at the temperature of 950$^{\circ}C$ in both the near gamma and the lamella structures. Further aging treatment for 12 hr at test temperatures has found to cause no softening in both microstructures.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2004년도 추계학술발표대회 개요집
• /
• pp.43-45
• /
• 2004

Brazing between cemented carbides and steel for tool investigated by copper alloy brazing filler. Copper alloy filler was high liquidus temperature($990^{\circ}C$), therefor the shank(steel) occurred softening. Because brazing sample was necessary to heat treatment after brazing process. This experiment, influence of austenite time and purge temperature on heat treatment were investigated. As a result, these treatments obtained to high deflective strength In case of austenite time was short and purge temperature was low. Especially, nitride precipitated brazing layers was strongly influenced by the deflective strength.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 추계학술대회논문집A
• /
• pp.210-215
• /
• 2001

The ferritic 2.25CrMo steel has been used for high temperature structure applications such as turbine rotors, boilers and pressure vessels in fossil plant and petroleum chemical facilities. However, this steel is known to result in aging degradation due to temper embrittlement, carbide induced brittleness and softening of matrix after long time exposure to high temperature. This research investigated the microstructural and mechanical changes after artificial degradation treatment and evaluated the degree of degradation by several nondestructive methods. The decrease of electrical resistivity and increase of magnetic Barkhausen noise(RMS voltage) with increasing aging time were observed. The change of electrical resistivity and Barkhausen noise showed a good correlation with the ductile-brittle transition temperature.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 1999년도 춘계학술대회논문집
• /
• pp.171-175
• /
• 1999

the high temperature deformation behavior of 304 stainless steel was characterized by the hot torsion test. Continuous deformation was carried out at the temperature ranges 900-110$0^{\circ}C$ and the strain rate ranges 5x10-2~5/sec. The formulation of the flow stress curves was developed as subtraction form which was based on dynamic softening mechanisms The volume fraction of dynamic recrystallization and the mean grain size could be expressed as a function of deformation variables temperature (T) strain ($\varepsilon$) strain rate ($\varepsilon$) The calculated values of flow stress and mean grain size could be well matched with experimental values.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2000년도 춘계학술대회논문집
• /
• pp.67-70
• /
• 2000

The tool life is not long enough under sever forming condition in warm forging. The tool life is affected by wear heat fatigue plastic deformation and so on. Especially wear is one of the most serious factors for tool life. To increase tool life we should consider various factors like processing design die design die materials lubrication and cooling system This study design to obtain the steady state temperature of die by FEM analysis under several conditions of cooling. There are four cooling conditions in this study no cooling internal cooling external cooling and both internal and external cooling. With above obtained temperatures tool life is predicted using Archard's model that is considered softening of die. The effect of internal cooling system is better than that of externally cooled die. To predict the die life the steady state temperature is calculated by using mean temperature of die. Considering only wear the die life much longer as the cooling effect is bigger. The more accurate die life will be predicted if we consider heat crack as well as wear.

• 한국분말재료학회지
• /
• 제2권3호
• /
• pp.231-237
• /
• 1995

The powder mixtures of Al, Ti and Cr were mechanically alloyed to obtain nanocrystalline powders of $Ti_{25}Cr_8Al_{67}$ composition. Both FCC phase and undissolved metal chromium formed by MA. During the annealing of the MA powders, the phase transition from FCC to ordered $Ll_2$ started at ~$300^{\circ}C$ and was completed below $600^{\circ}C$. As a result of the high-temperature compressive test for the MA powder compacts, the stress-strain curves showed serrated yielding behavior at 400 and $600^{\circ}C$, and softening phenomenon below the strain rate of $5{\times}10^{-3}s^{-1}$ at $800^{\circ}C$. The compressive yield strength as a function of test temperatures showed the nature of the positive-temperature dependence which has the peak temperature around $600^{\circ}C$.

• 한국전기전자재료학회논문지
• /
• 제18권11호
• /
• pp.1019-1023
• /
• 2005

We have examined the electrical and optical characteristics of the plasma display panel produced by vacuum in-line sealing technology. In the MgO layer deposited at room temperature, after sealing at the panel temperature of $430^{\circ}C$, the luminous efficiency decreased compared with that of the panel before sealing. Moreover, firing and sustain voltage of the sealed panel increased compared with that of the panel before sealing. This was resulted from that the MgO protective layer was cracked by the softening of the dielectric layer during the sealing process. In order to avoid the MgO crack during the vacuum in-line sealing, thermally stable MgO layer or lower temperature sealing is required.