• Journal of the Korean Chemical Society
• /
• v.48 no.3
• /
• pp.273-282
• /
• 2004

The synthetic technology of improved polyaluminiumchloride (IPAC) similar to characteristics of PACS was established with minimum expense for modifying existing production line. The conditions for activating silicate was studied before the synthesis of IPAC, and the IPAC was synthesised with raw materials such as aluminumhydroxide and concentrated hydrochloric acid, followed by adding activated silicate and alginate. The specification of product, chemical structure, and coagulating properties were tested by using specification testing method, instrumental analytical method, and Jar tester, respectively. As a result, the product, IPAC, contained aluminium oxide content more than 17%, and no precipitation was shown at all while the IPAC solution was preserved, and the larger floc and faster coagulation were represented compared to existing PAC under the same conditions. It was suggested that these synthetic technology could be applied to the existing production line for producing PAC without approximately cost raising factor because of adding sulfuric acid-activated silicate instead of sodium sulfate.

• Journal of the Korean Wood Science and Technology
• /
• v.31 no.1
• /
• pp.46-51
• /
• 2003

The feasibility of using bleaching treatments for removing fungal stain was evaluated on heavily stained raiadta pine sapwood. Sodium chlorite and sodium hypochlorite appeared to destain fungal discoloration by providing proper treatment conditions (chemical concentration, treatment temperature, and treatment time), while hydrogen peroxide did not remove fungal stain under the bleaching regimes evaluated. The addition of sodium silicate and sodium hydroxide in the hydrogen peroxide solution as a buffer could remove fungal discoloration completely; however, the color of wood surface turned faint green after bleaching, thereby reducing the lightness of bleached samples. The results suggest that hydrogen peroxide bleaching could be a feasible method for removing fungal discoloration of stained radiata pine sapwood, although further research is needed to solve the problem of color change after bleaching. Also, further tests under field conditions are recommended.

• Journal of Radiation Industry
• /
• v.4 no.4
• /
• pp.347-352
• /
• 2010

In this study, we addressed a novel nanosized curdlan-silica complex, which is curdlan bound to silica, for the development of a sustain-releasing micro element fertilizer formulation. The complex was obtained as follow steps; First, Curdlan polymer, sodium silicate ($Na_2SiO_3$) and isopropyl alcohol were dissolved in DDW. Next the resultant solution was irradiated by $^{60}Co$ gamma-irradiator (150 TBq of capacity; ACEL, Canada). Then $MgSO_4$ was treated with the resultant solution. The obtained colloidal solution was dried by freeze dryer. Finally, we obtained a novel nanosized curdlan-silica formulation containing $MgSO_4$ from the colloidal solution. The morphology of the complex was characterized by using scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The nanosized curdlan-silica complex has a particle size ranging from 20 to 80 nm and high stability. Our results suggested that the nano-complex can be applicable to use in various sustain-releasing formulation for pesticide delivery system (PDS).

• Journal of Surface Science and Engineering
• /
• v.54 no.5
• /
• pp.238-247
• /
• 2021

PEO (plasma electrolytic oxidation) was applied to modify the surface of AZ31 magnesium alloy in this study. The mixed solution of sodium hydroxide (NaOH) and sodium silicate (Na₂SiO₃) was used as the electrolyte, and 0 - 0.05 g/L of Ca-GP (Glycerol Phosphate Calcium salt) was added in the electrolyte as an additive. PEO treatment was conducted at a current density of 30mA/cm² for 5 minutes using a DC power supply. The surface properties were identified by SEM, XRD and surface roughness analyses, and the corrosion resistance was evaluated by potentiodynamic polarization and immersion tests. In addition, the biocompatibility was evaluated by immersion test in SBF solution. As the concentration of Ca-GP was increased, the surface morphology was denser and more uniform, and the amount of Ca and the thickness of oxide layer increased. Only Mg peak was observed in XRD analysis due to very thin oxide layer. The corrosion resistance of PEO-treated samples increased with the concentration of Ca-GP in comparision with the untreated sample. In particular, the highest corrosion resistance was identified at the group of 0.04g Ca-GP through potentiodynamic polarization and immersion tests in saline solution (0.9 wt.%NaCl). During the immersion in saline solution, pH rapidly increased at the beginning of immersion period due to rapid corrosion, and then increase rate of pH decreased. However, the pH value in the SBF temporarily increased from 7.4 to 8.5 during the day, then decreased due to the inhibition of corrosion with HA(hydroxyapatite) formation.

• Journal of the Korea Concrete Institute
• /
• v.19 no.5
• /
• pp.647-653
• /
• 2007

In ready mixed concrete factory, in case of using the high molecular additive in winter especially the liquid additive for the early strength, it is required to check the stability. In this research, the freezing and gelling characteristics of the liquid additive for the early strength is reviewed, the material and mechanical solution are proposed to that the practical quality control method will be suggested. As the result, the Freezing temperature of the liquid additive for the early strength is $-11.8^{\circ}C$, and it is the lower than the temperature at which the strength is shown. By making with sodium silicate of $37{\pm}0.5%$ designed by $SiO_2\;and\;Na_2O$ in 0.31 of mol ratio, it minimizes the gelling at the lower temperature. On the other hand, facilities for storing and supplying the material should be set at $40^{\circ}C$ so the temperature distribution is well spreaded for practical operation.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.15 no.11
• /
• pp.6952-6957
• /
• 2014

In photocatalysis, the addition of metal matter to $TiO_2$ can alter the surface properties. As such, the metal can increase the rate of the photodegradation reaction. In this study, a range of modified $TiO_2$ photocatalysts were prepared and tested to improve the activity of photodegradation at a batch-typed photoreactor. To obtain a good sol solution of the $TiO_2$ photocatalyst, several types of dispersion agents and stabilizers were investigated. The photocatalyst solutions were modified with isoproply alcohol as the dispersion agent and sodium silicate as the stabilizer. The effects of various metallic elements on enhancing the photocatalytic activity of $TiO_2$ on the degradation of toluene were examined. Palladium-added $TiO_2$ was found to be the best, whereas copper or tungsten-added also showed good results. In the case of palladium addition, the increase in removal efficiency was 25%. On the other hand, Fe-added $TiO_2$ showed a notable decrease in photocatalytic degradation. Additional doping of copper or tungsten on the $Pd/TiO_2$ had no positive effect on the photodegradation activity.

• Applied Chemistry for Engineering
• /
• v.22 no.2
• /
• pp.209-213
• /
• 2011

Hydrophobic silica aerogel beads with low thermal conductivity and high porosity were prepared using a cost-effective sodium silicate as a silica source via an ambient-pressure drying process. Monolithic wet gels were first prepared by adjusting pH (~5) of a diluted sodium silicate solution. The silica aerogel beads (0.5~20 mm) were manufactured by breaking the wet gel monoliths under a simultaneous solvent exchange/surface modification process and an ambient-pressure drying process without using co-precursors or templates. Dried silica aerogel beads exhibit a comparable porosity ($593m^2/g$ of surface area, 34.9 nm of pore size, and $4.4cm^3/g$ of pore volume) to that of the aerogel powder prepared in the same conditions. Thermal conductivity of the silica aerogel beads (19.8 mW/mK at $20^{\circ}C$) is also identical to the aerogel powder.

• Advances in materials Research
• /
• v.9 no.3
• /
• pp.219-231
• /
• 2020

The aim of this study is to investigate the durability of fly ash based geopolymer mortar with and without protective coatings in aggressive chemical environments. The source materials for geopolymer are Fly ash and Ground Granulated Blast furnace Slag (GGBS) and they are considered in the combination of 80% & 20% respectively. Two Molarities of NaOH solution were considered such as 8M and 10M. The ratio of binder to sand and Sodium silicate to Sodium hydroxide solution (Na₂SiO₃/NaOH) are taken as 1:2 and 2 respectively. The alkaline liquid to binder ratio is 0.4. Compressive strength tests were conducted at various ages of the mortar specimens. In order to evaluate the performance of coatings on geopolymer mortar under aggressive chemical environment, the mortar specimens were coated with two different types of coatings such as epoxy and Acrylic. They were then subjected to different chemical environments by immersing them in 10% standard solutions of each ammonium nitrate, sodium chloride and sulphuric acid. Drop in compressive strength as a result of chemical exposure was considered as a measure of chemical attack and the drop in compressive strength was measured after 30 and 60 days of chemical exposure. The compressive strength results following chemical exposure indicated that the specimens containing the acrylic coating proved to be more resistant to chemical attacks. The control specimen without coating showed a much greater degree of deterioration. Therefore, the application of acrylic coating was invariably much more effective in improving the compressive strength as well as the resistance of mortar against chemical attacks. The results also indicated that among all the aggressive attacks, the sulphate environment has the most adverse effect in terms of lowering the strength.

• Journal of Sericultural and Entomological Science
• /
• v.25 no.2
• /
• pp.44-50
• /
• 1984

The effects of sodium pyrophosphate, sodium tripolyphosposphate and ethylene diamine tetraacetic acid as a degumming aid reagent were investigated under the conditions of underground water and dimineralized water for the scouring water sources. The changes of water qualities by adding the condensed sodium phosphates and the physical properties of scoured silk fabric were examined, respectively. 1. The water hardness of underground water was decreased by adding the condensed sodium phosphates and it was further reduced according to the increasing temperature. The water hardness reducing power of sodium pyrophosphate was a little stronger than that of sodium tripolyphosphate. 2. The sodium silicate as an alkaline reagant for scouring decreased the water hardness, but the sodium carbonate increased it in the underground water. 3. The pH value of 0.4% soap and 0.25% sodium silicate mixed solution after boiling was. 9.80, but it was leveled upto 9.90 by adding 0.05% sodium pyrophosphate and upto 9.95 by 0.02% ehtylene diamine tetraacetic acid, respectively. 4. The masking action of Fe$\^$3+/ ions dissolved in the scouring water was more remarkable by ethylene diamine tetraacetic acid than by the condensed sodium phosphates. Of the condensations, sodium tripolyphosphate was more effective than sodium pyrophosphate in the action. 5. Genrally, the dimineralized water scouring increased the boil-off ratio with reducing the flexural rigidity of fabric which was negatively related with the favorablility of hand-touch more than the underground one did. 6. Under the underground water scouring, the addition of ethylene diamine tetraacetic acid increased the boil-of ratio and compressive elasticity of fabric with reducing the flexural rigidity more than that of the condensed sodium phosphates did. 7 The additions of sodium tripolyphosphate and ethylene diamine tetraacetic acid reduced the flexural rigidity of fabric with raising the boil-off ratio even in the dimineralized water scouring, but there was no sifnificant difference between both of them.

• Journal of Radiation Industry
• /
• v.5 no.4
• /
• pp.305-311
• /
• 2011

We introduced a novel sustainable slow-releasing agrochemical formulation, a biopolymer bound to silica, for controlling plant diseases. The formulation was obtained through the following process. Curdlan, sodium silicate ($Na_2SiO_3$) and isopropyl alcohol were dissolved in DDW (Deionized-distilled water). The resultant solution was then irradiated using a $^{60}Co$ ${\gamma}$-irradiator (150 TBq of capacity; ACEL, Canada) at KAERI. The resultant solution was treated with phosphorous acid ($H_3PO_3$). Finally, we obtained a novel biopolymer-silica microsized formulation containing phosphorous acid ($H_3PO_3$) from the solution. The morphology of the complex was characterized using scanning electron microscopy (SEM) and transmission electron microscopy (TEM). SEM and TEM images revealed that the curdlan-silica formulation has a particle size ranging from 1 to $3{\mu}m$ with high stability. We also detected that $H_3PO_3$ was distributed within the formulation through energy dispersive X-ray spectroscopy (EDX) analysis. $H_3PO_3$ was sustain-released from the formulation in water. Based on our results, it seems effectively that one or two applications of the formulation during a cropping season will assist in controlling various plant diseases.