• Korean Chemical Engineering Research
• /
• v.61 no.2
• /
• pp.265-272
• /
• 2023

Lignocellulosic biomass is essential to pretreatment because of having rigid structures and a lot of lignin. Among methods of pretreatment, using THF solvents has the advantage of being easy to reuse. THF (Tetrahydrofuran) used as a co-solvent with water or ionic solvent that is inexpensive and can remove lignin over a wide range of reaction conditions. NaOH (Sodium hydroxide) has been demonstrated to preferentially solvate lignin from cellulose. Thus, NaOH was used as a pretreatment co-solvent for the fractionation of lignin by destroying the ether bond to amend for hydrolysis and expand the surface area of cellulose and hemicellulose. In this experiment, lignin was removed by the NaOH/THF co-solvent pretreatment process to characteristics for the pretreatment and obtain the optimal levulinic acid conversion yield through the acid catalyst conversion process. the NaOH/THF co-solvent system was conducted in various ratios of co-solvent under a total of 16 conditions. And the temperature was 180 ℃ during to 60 mins. The optimum condition of co-solvent is NaOH 5 wt%/THF 90:10(v/v%), 76.8% glucan content was obtained through this co-solvent pretreatment, and 90.1% lignin was removed. In the acid catalyst conversion process, which is a subsequent pretreatment process, the experiment was conducted under the conditions of 30 to 90 min of reaction time and 160 ℃ to 200 ℃ reaction temperature. The optimum condition of acid catalyst conversion process is 60min reaction time under of 180 ℃, and it obtained 84.7% of levulinic aicd conversion yield.

• Fibers and Polymers
• /
• v.3 no.1
• /
• pp.1-7
• /
• 2002

Cellulose carbonate was prepared by the reaction of cellulose pulp and $CO_2$ with treatment reagents, such as aqueous $Zncl_2$ (20-40 wt%) solution, acetone or ethyl acetate, at -5-$0^{\circ}C$ and 30-40 bar ($CO_2$) for 2 hr. Among the treatment reagents, ethyl acetate was the most effective. Cellulose carbonate was dissolved in 10% sodium hydroxide solution containing zinc oxide up to 3 wt% at -5-$0^{\circ}C$. Intrinsic viscosities of raw cellulose and cellulose carbonate were measured with an Ubbelohde viscometer using 0.5 M cupriethylenediamine hydroxide (cuen) as a solvent at $20^{\circ}C$ according to ASTM D1795 method. The molecular weight of cellulose was rarely changed by carbonation. Solubility of cellulose carbonate was tested by optical microscopic observation, UV absorbance and viscosity measurement. Phase diagram of cellulose carbonate was obtained by combining the results of solubility evaluation. Maximum concentration of cellulose carbonate for soluble zone was increased with increasing zinc oxide content. Cellulose carbonate solution in good soluble zone was transparent and showed the lowest absorbance and the highest viscosity. The cellulose carbonate and its solution were stable in refrigerator (-$5^{\circ}C$ and atmospheric pressure).

• FLOWER RESEARCH JOURNAL
• /
• v.16 no.1
• /
• pp.17-22
• /
• 2008

Four kinds of leaves with different shapes of leaf blade were used as experimental materials to establish an optimum condition for treating leaves to obtain skeleton leaves. Effective concentration and length of soaking time in a hot NaOH solution, which resulted in high valued ornaments, were 60% (v/v) for 50 minutes for Acer buergerianum (palmatifid), 20% (v/v) for 50 minutes for Ilex cornuta (serrate), 20-60% (v/v) for 70 minutes for Quercus mongolia (lobed), and 20-40% (v/v) for 70 minutes for Quercus palustris (parted). Through a series of the process of soaking leaves in a hot NaOH solution, rinsing or brushing to remove mesophyll, drying, and dying, high quality ornaments could be obtained.

• Journal of the Korea Concrete Institute
• /
• v.24 no.2
• /
• pp.137-145
• /
• 2012

Strength model for blasted furnace slag mortar blended with sodium was investigated in this study. The main parameters of AAS (alkali activated slag) mortar were dosage of alkali activator, water to binder ratio (W/B), and aggregate to binder ratio (A/B). For evaluating the property related to the dosage of alkali activator, sodium carbonate ($Na_2CO_3$) of 4~8% was added to 4% dosage of sodium hydroxide (NaOH). W/B and A/B was varied 0.45~0.60 and 2.05~2.85, respectively. An alkali quality coefficient combining the amounts of main compositions of source materials and sodium oxide ($Na_2O$) in sodium hydroxide and sodium carbonate is proposed to assess the compressive strength of alkali activated mortars. Test results clearly showed that the compressive strength development of alkali-activated mortars were significantly dependent on the proposed alkali quality coefficient. Compressive strength development of AAS mortars were also estimated using the formula specified in the previous study, which was calibrated using the collected database. Predictions from the simplified equations showed good agreements with the test results.

• Textile Coloration and Finishing
• /
• v.12 no.4
• /
• pp.233-238
• /
• 2000

In this study, the control system of sodium hydroxide was demonstrated to systemize hydrolysis process in polyester dyeing. We mainly focused on the application method of acid-alkali titration for the polyester hydrolysis machine of liquor-flow type. Industrial pH meter with electrode type was used for identifying equivalence point. Three units which were analogue-to-digital card, microprocessor and digital output card were used to control NaOH concentration in the control part of the system. The yielded data are translated to the microprocessor through analogue-digital interfacing card. After calculating, NaOH concentration in NaOH storage tank was controlled through the digital output card and solenoid valves.

• Proceedings of the KSME Conference
• /
• 2008.11b
• /
• pp.2415-2418
• /
• 2008

Polydiacetylenes (PDAs) are very attractive chemical substances which have distinctive features of color change and fluorescence emission by thermal or chemical stress. Especially, when PDAs contact with solutions of a particular pH, such as a strong alkaline sodium hydroxide (NaOH) solution or a strong acidic hydrogen chloride (HCl) solution, PDAs change their color from non-fluorescent blue to fluorescent red. In this study, we propose a novel method to detect alkaline pH using PDAs and NaOH solutions by hydrodynamic focusing on a microfluidic chip. Preliminary results indicate that the fluorescent intensity of PDAs increases in respond to the NaOH solution concentrations. Also, the fluorescence is quenched back when the PDAs are in contact with a HCl solution. These results are useful in a microfluidic PDA sensor chip design for pH detection.

• Journal of environmental and Sanitary engineering
• /
• v.15 no.1
• /
• pp.95-101
• /
• 2000

This study was investigated to the reaction of alumina sintering with alkaline. The soluble $NaAlO_2$ was made after the commercial ${\alpha}-Al_2O_3$ was calcinated with NaOH. The reaction of alumina was carried out to be based on the effects of calcination temperature, time, and the mixing ratio of ${\alpha}-Al_2O_3/NaOH$. The alumina was calcined over $500^{\circ}C$ with NaOH powder after it was sieved with 170/270 mesh. The calcined alumina with NaOH powder was dissolved into $25^{\circ}C$ distilled water and filtrated, and HCI was added to adapt pH 6.5~7.5. The residue was separated with vacuum pump for filtration after it was adapted to proper pH, and aluminum compound was precipitated with $Al(OH)_3$. The investigation was carried out with the variables; the calcination temperature($500-900^{\circ}C$), the calcination time (30~90 min), and the concentration of HCI when leaching(0.5~3.0N) respectively. In this investigation, the main product of ${\alpha}-Al_2O_3$ and NaOH was $NaAlO_2$ and the maximum conversion ratio was 91.4% under the optimum conditions as followed ; the ratio of NaOH/${\alpha}-Al_2O_3$ was 1.5 and the calcination conditions were $800^{\circ}C$ and 90 min.

• Journal of the Korean institute of surface engineering
• /
• v.44 no.2
• /
• pp.44-49
• /
• 2011

The films formed on AZ31B magnesium alloy were prepared from alkaline solution composed of potassium permanganate and sodium hydroxide. The immersion tests were carried out at the different concentration of sodium hydroxide and pre-treatment method in 5 minute. The morphology and the phase composition of the film were characterized by scanning electron microscopy (SEM) and X-ray diffraction (XRD). The corrosion behavior of the film in 5.0% NaCl solution was evaluated using potentiodyanmic polarization. Open circuit potential in developing film was examined with time. The thin and transparent film was mainly composed of MgO and $Mg(OH)_2$. The film with the best corrosion resistance was obtained at $70^{\circ}C$ bath temperature, 1.6 M concentration of sodium hydroxide and chemical pre-treatment.

• The Korean Journal of Food And Nutrition
• /
• v.26 no.3
• /
• pp.601-607
• /
• 2013

This study was performed to investigate the changes of total and soluble ${\beta}$-glucan contents, purity and physicochemical characteristics of alkali hydrolyzed barley varieties: Saessalbori (SSB), Saechalssalbori (SCSB) and Hinchalssalbori (HCSB). The barleys were hydrolyzed at different concentrations of sodium hydroxide (0.2~1.0 N) for 12 hours. Total ${\beta}$-glucan contents of raw SSB, SCSB and HCSB were 8.40, 7.77 and 8.28%, and soluble ${\beta}$-glucan contents were 4.80, 4.16 and 4.61%, respectively. The total ${\beta}$-glucan contents after alkali hydrolyzed at 1.0 N NaOH were 7.54, 6.89 and 7.54%, also soluble ${\beta}$-glucan contents were 4.82, 4.30 and 4.55%, respectively. The degree of purity of soluble ${\beta}$-glucan in SSB, SCSB, and HCSB were 35.79, 30.91 and 33.90%, respectively. They were increased to 74.02, 75.28 and 81.41% after hydrolyzed at 1.0 N NaOH, respectively. The molecular weight and viscosity of soluble ${\beta}$-glucan solutions were decreased as sodium hydroxide concentration was increased. The re-solubility of raw barley ${\beta}$-glucan was about 50%; however, it was increased to approximately 87% as sodium hydroxide concentration was increased.

• Journal of the Korean Home Economics Association
• /
• v.25 no.4
• /
• pp.9-18
• /
• 1987

This study is conducted to investigate the influence of addition of quarternary ammonium salt(cetyl trimethyl ammonium bromide: CTAB) when polyester(PET) fabric is treated with sodium hydroxide(NaOH), depending on experimental variables such as CTAB concentration, NaOH concentration, time & temperature, and the change in physical & chemical properties of alkaline-hydrolyzed PET fabrics depending on their weight loss. The results are as follows: 1. By adding CTAB in aqueous NaOH, the weight loss of PET fabric is increased remarkably and until the concentration of CTAB is reached at its cmc, and the higher the concentration of CTAB are, the more weight loss on PET fibrics are. 2. The addition of CTAB in aqueous NaOH is most effective at lower NaON concentration(2%) among various NaOH concentration, on increasing the amount of weight loss, while there are almost similar results through various treatment time and temperature. 3. As the amount of weight of weight loss on PET fabric is increased, the increase of void space in the PET yarn, of softness & dyeability of PET fabric and the decrease of tensile strength are found. On the other hand, the moisture regain shows a little increase by alkaline-hydrolysis on PET fabric while vertical absorption test & water retention value are not sufficiently sensitive to distinguish between the hydrophillicity of untreated and treated PET fabric. The shrinkage of PET fabric is induced by swelling in hot aqueous NaOH regardless of NaOH concentration & addition of CTAB.