• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.48 no.3
• /
• pp.44-50
• /
• 2016

As a raw material for pulp and paper industry, Moso bamboo, Timber bamboo and Henon bamboo pulps were prepared by soda or soda-anthraquinone(Soda-AQ) pulping process. Soda-AQ pulp yields was higher in Henon bamboo (43.2%) than in Moso bamboo or Timber bamboo (32.7-39.2%), but quite lower than hardwood species. In Kappa number comparison, Henon bamboo pulp showed lower (16.6) with 50 min cooking to $170^{\circ}C$ than that of Moso bamboo (22.8) and Timber bamboo (18.9) with 90 min cooking to $170^{\circ}C$. Fiber length of Timber bamboo soda pulp had higher (1.46 mm) than that of Moso bamboo or Henon bamboo (1.18-1.36 mm). All three bamboo pulps showed longer average fiber length than commercial hardwood pulp. With higher pulp yield and lower Kappa number, Henon bamboo is better raw material for pulp than Moso bamboo and Timber bamboo.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.48 no.2
• /
• pp.13-19
• /
• 2016

Moso Bamboo was investigated as the a raw material for pulp and paper industry. Soda-Anthraquinone (Soda-AQ) pulping, elemental chlorine free bleaching was applied. Yield of soda or soda-AQ pulp was 29.3-31.7% with Kappa number 33.0-22.8 with different cooking time or anthraquinone addition at 20% active alkali. In soda or soda-AQ pulping, 81-86% of xylan was removed, which was the main reason for lower pulp yield than hardwood species. Average fiber length of Moso Bamboo soda-AQ pulp was 1.36 mm with $15.5{\mu}m$ fiber width. Soda-AQ pulp from Moso Bamboo (P-3, lowest Kappa pulp) was bleached with 5.5-6.5% of chlorine dioxide charge as D0ED1 bleaching sequence. In 3-stages ECF bleaching, final brightness of 85.3% ISO was achieved with total chlorine dioxide 6.5%.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.47 no.5
• /
• pp.85-90
• /
• 2015

To use the African tulip tree (Spathodea campanulata) as raw material for chemical pulping, soda and soda-AQ pulping was investigated. In chemical compositional analysis, lignin contents of African tulip (33.1%) was higher than other hardwood such as Yellow poplar (17.5%), Acacia (27.1%), or Eucalyptus (24.2%). Soda or soda-AQ pulping with African tulip tree resulted in yield at 43.4-44.8% with 29.5-34.5 Kappa number, pulping condition with 20-22% active alkali. Kappa number of African tulip tree pulp was quite higher than other tropical hardwood (Eucalyptus or Accacia) with less yield due to higher lignin content in wood. Fiber length and width of pulp from African tulip tree was similar to Accacia pulp and shorter than eucalyptus pulp.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.42 no.3
• /
• pp.22-27
• /
• 2010

Pulping properties of the imported mixed eucalyptus chips and the domestic yellow poplar chips were investigated for comparing two chips as the raw materials for the hardwood chemical pulp. Soda-AQ (anthraquinone) pulping was applied for this study. The pulp from yellow poplar showed higher pulp yield than pulp from mixed eucalyptus, which comes from the lower hot-water soluble extractives and the higher polysaccharides in yellow poplar chips than those of the mixed eucalyptus chips. The yellow poplar pulp had higher average fiber length and fiber width than those of the mixed eucalyptus pulp, which led to the better respond to beating and the higher tear strength than those of the pulp from the mixed eucalyptus chips.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.32 no.2
• /
• pp.58-67
• /
• 2000

This study was carried out to acquire basic data necessary for the use of non-wood pulp. Various chemical pulping methods for rice straw to achieve higher yield, lower Kappa No. were investigated and then the physical properties of various pulps were tested. The results of this study were as follows: When various chemical pulps (Soda, Soda-AQ, Soda-$H_2O_2$, Soda-$Na_2S_2$, AS, AS-AQ, AS-$Na_2S_2O_3$, AS-$Na_2S_2O_4$, Kraft) were produced with rice-straw, the pulps with the highest yield and lowest Kappa No. were obtained with Soda-$Na_2S_2$and AS-$Na_2S_2O_4$pulps. For the breaking length, Soda and Soda-additive pulps(7.5~9.2km) were better than AS and AS-additive pulps(6.2~8.1km). Similarly, for the burst index, Soda and Soda-additive pulps(6.0~7.0 kPa.$m^2$/g) were better than AS and AS-additive pulps(4.5~6.3 kPa.m$^2$/g). But the tear index was showed 21.8-30.9 mN.$m^2$/g with a little different between pulping methods.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.32 no.3
• /
• pp.57-64
• /
• 2000

This study was carried out to acquire basic data necessary for the use of non-wood pulp. It investigated various chemical pulping methods using bamboo to achieve higher yield lower kappa no. and then the physical properties of various pulps were tested. The results of this study were as follows. When various chemical pulps(Soda, Soda-AQ, Soda-AQ-H2O2, Soda-urea, AS, AS-AQ, Kraft) were produced with bamboo. the pulps with the higher yield and lower kappa no. were AS-AQ and Kraft. In the case of the breaking length Soda pulps(5.77∼6.46 km) showed the greatest and Soda-urea pulps(3.81∼4.522km) showed the lower value. Similarly for the burst index Soda pulps (3.28∼3.50 kPa$.$m2/g) were the best and Soda-urea pulps(2.29∼2.39 kPa$.$m2/g) were worst. On the other hand the tearing indexes of AS-AQ pulps(73.6∼89.7mN$.$m2/g) showed the tendency which was higher then those of other pulps.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.47 no.6
• /
• pp.73-80
• /
• 2015

Corn stalk is the lignocellulosic biomass, which remain as leftover after harvesting. To use the corn stalk as raw material for paper industry, soda pulping was applied. In chemical compositional analysis, extractive contents of corn stalk (45.1%) was higher than hardwood. With corn stalk pith, soda pulp yield was 25.3% at 10.6 Kappa number, but 39.5% yield with 14.8 Kappa number for corn stalk rind. Higher extractives content in pith is one of the reason for lower pulp yield than rind. Pith pulp fibers had higher fines content than rind pulp. Pith parenchyma cell was removed as fines during pulping or washing process, which caused the lower yield. To use the corn stalks as a raw material for paper making, de-pith process is essential for higher pulp yield and longer pulp length.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.41 no.4
• /
• pp.52-57
• /
• 2009

Soda and kraft pulping experiments were carried out in order to investigate the pulping characteristics of bamboo grown in Vietnam. The merit of kraft pulping was not observed for bamboo pulping from the viewpoint of delignification and screened pulp yield. The improvements of delignification during soda and kraft pulping of bamboo were observed by the addition of AQ. The bamboo pulp leaded the bulkier structure than those made from SwBKP and HwBKP. The average fiber length was 1.62mm which is shorter than those of SwBKP, but longer than those of HwBKP. It was found that the physical properties of bamboo pulp sheet could be varied by the pulping method, cooking condition, AQ addition, bleaching and refining etc.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.42 no.2
• /
• pp.88-94
• /
• 2010

Cattail (Typha L.) was used as a raw material for producing both bio-ethanol and pulp for papermaking at the same time. Pretreatments of cattail stems and leaves with acid ($H_2SO_4$) and alkali (NaOH) in three different addition levels were studied before soda pulping. The acid pretreatment gave reducing sugar of 15.2% of initial weight, but alkali pretreatment close to 1%. Soda pulping of the pretreated cattail gave 3% reduction in pulp yield and less bonding properties in paper; however, refining of the pulp from the pretreated cattail with alkali restored their fiber bondings up to that of the pulp from no-pretreated cattail at equivalent freeness.

• Journal of the Korean Chemical Society
• /
• v.56 no.2
• /
• pp.257-263
• /
• 2012

The selection of suitable delignification conditions and optimization of process variables is crucial to the successful operation of chemical pulping processes. Soda pulping of Carpolobia lutea was investigated, as an alternative raw material for pulp and paper production. The process was optimized under the influence of three operational variables, namely, temperature, time and concentration of cooking liquor. Equations derived using a second - order polynomial design predicted the pulp yield and lignin dissolution with errors less than 8% and 11% respectively. The maximum variations in the pulp yield using a second order factorial design was caused by changes in both time and alkali concentration. Optimum pulp yield of 43.87% was obtained at low values of the process variables. The selectivity of lignin dissolution was independent of the working conditions, allowing quantitative estimations to be established between the pulp yield and residual lignin content within the range studied.