• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2005년도 춘계학술대회
• /
• pp.361-365
• /
• 2005

Since the fuel cell uses the hydrogen for its fuel. it has no emission and higher efficiency than an internal combustion engine. Also fuel cell is much quieter than engine generator and generates heat much less than engine generator. So it has advantage of Army's 'si lent watch' capability and the ability to operate undetected by the enemy. The fuel cell hybrid system combines a fuel cell power system with an ESS. The ESS (e.g., batteries or ultracapacitors) reduces the fuel cell's peak power and transient response requirements. It allows the fuel cell to operate more efficiently and recovery of vehicle energy during deceleration. The battery has high energy density, so it has the advantage regarding driving distance. However, it has a disadvantage considering dynamic characteristic because of low power density. One other hand. the ultracapacitor has higher power density, so it can handle sudden change or discharge of required power. Yet. it has lower energy density. so it will be bigger and heavier than the battery when it has the same energy. This paper proposes the power management strategy for multi-power source fuel cell hybrid system. which is applied with the merits of both battery and ultra capacitor by using both of them simultaneous.

• Applied Biological Chemistry
• /
• 제20권1호
• /
• pp.33-42
• /
• 1977

콩나물에 많이 존재하는 Asn의 생합성(生合成)에 관하여 연구하고자 콩나물 생육기간중(生育其間中) 수분함량(水分含量) 및 Asn 함량을 조사한 결과 10일째 수분(水分)은 $85{\sim}90%$에 달했으며 Asn은 6일째부터 급격히 증가하여 10일째는 건물량(乾物量)의 22.7%에 달하였다. 콩나물 100 g에서 Asn을 추출(抽出)한 결과 2.29g을 얻었고 재결정하여 1.62 g을 얻었다. 콩나물 생육시(生育時) $NH_4Cl,\;(NH_4)_2SO_4$ 및 urea를 살포하여 질소화합물에 대한 영향을 고찰하였던 바 $NH_4Cl$ 및 $(NH_4)_2SO_4$구(區)는 Asn이 control보다 약간 증가하였으나 urea구(區)는 10일째 29.5%로 증가하였다. 콩나물에서 asparagine synthetase를 $(NH_4)_2SO_4$ fractionion 및 Sephadex G-150에 의해 정제하여 8.6배 정제하였다. 이 효소는 매우 불안정(不安定)하였으나 glycerol, mercaptoethanol 및 기질(基質)인 ATP, $Mg^{++}$이온에 의해 보호를 받았으며 이 산소(酸素)에 의해 최고(最高)의 Asn이 생성(生成)되는 ATP, Gln(또는 ${NH_4}^+$)의 농도는 표준반응 용액에서 각각의 구성농도를 변화시키면서 측정하였을 때 ATP 10 mM, ${NH_4}^+$는 50 mM, Gln은 10 mM이었다. $Mg^{++}$이온 대신 $Mn^{++}$, $Zn^{++}$, 및 $Fe^{++}$로 대치할수 없었으며 Asp에 대한 Km값은 3.1 mM이었고 효소작용의 최적(最適) pH는 7.5이었다. Amide donor로서 $NH_2OH$로 대치한 결과 ${\beta}-aspartyl$ hydroxamate가 생성(生成)되어, 효소의 열불안성(熱不安性), amide donor로서 Gln 이용 및 SH기(基)에 의한 효소안정성을 비추어 보아, 같은 두과식물(荳科植物)인 완두와 비슷하게 asparagine synthetase는 ${\beta}-aspartyl$ adenylate의 중간반응(中間反應)을 거치는 기작(機作)에 의해 Asn을 생합성(生合成)하는 것을 알았다.

• 한국식품영양과학회지
• /
• 제41권1호
• /
• pp.41-48
• /
• 2012

본 연구에서는 흰점박이꽃무지 함유 음료의 총폴리페놀함량과 항산화활성(DPPH 라디칼 소거능, TRAP, ORAC assay, comet assay) 및 사용에 대한 안전성을 검증하기 위하여 ICR mouse를 사용하여 흰점박이꽃무지 무첨가군과 첨가군 단회 투여(2 g/kg) 시 나타나는 치사율, 체중, 생리적 증상, 장기무게, 생화학적 분석(triglyceride, total cholesterol, HDL-cholesterol, LDL-cholesterol, aspartate transaminase, alanine transaminase)을 통해 급성독성시험을 실시하였다. 흰점박이꽃무지를 함유한 호박, 알로에, 돼지감자음료 1 pack의 총 페놀함량은 66.35~100.98 mg/pack, DPPH 라디칼 소거능은 67.1~90.0%/1 pack, TRAP 값은 $1.46\sim1.54{\mu}M$/trolox equivalent(TE)를 보였으며, 모든 음료의 ORAC 값은 1500보다 높았다. 모든 음료는 인체 임파구에서 세포독성을 보이지 않았으며, $H_2O_2$에 대한 DNA 손상에 대한 보호효과는 유의적이었다. 흰점박이꽃무지 첨가/무첨가 음료의 ICR mouse 암수 각각에 경구투여(2 g/kg) 후 14일까지 치사된 실험동물은 관찰되지 않았으며, 체중, 생리적, 병리적 및 생화학적 분석에서 대조군과 비교 시 그룹들 간의 유의한 변화는 관찰되지 않았다. 그러므로 2 g/kg의 흰점박이꽃무지 첨가/무첨가 음료를 ICR mouse에 단일 경구투여시 독성이 없는 것으로 판명되었다. 본 연구에서 규명된 흰점박이꽃무지 함유 음료의 항산화활성과 안전성은 산업적측면에서 약용 및 식용 자원으로 적극적인 활용을 기대할 수 있을 것으로 사료된다.

• 한국표면공학회지
• /
• 제14권4호
• /
• pp.215-220
• /
• 1981

The surface appearance of chromium electrodeposit was studied by employing a pulse curr-ent plating in self-regulating high speed (SRHS) bath containing 20 g/$\ell$, K2SiF6 7.5 g/$\ell$ SrSO4 and 250 g/$\ell$ CrO3. As the pulse frequency increased, the surface appearance changed suddenly from bright a-ppearance in a direct current plating condition to gray one in the range of pulse frequency less than about 20KHz. However the bright appearance is recovered as the pulse frequen-cy exceeded 20 KHz. This phenomena seemed to be related with the preferred orientation of electrodeposits, considering the relationship between the preferred orientation of elect-rodeposits and surface appearance in a SRHS bath. Direct current plating was also applied to both Sargent and SRHS bath and investigat-ion on surface appearance was extended to the high current density of 400 A/dm2. In a Sa-rgent bath, the increase in bath temperature was necessary for bright appearance as the current density was increased within 150 A/dm2, but bright region was shown in the cons-tant temperature of 70-75$^{\circ}C$ above the current density of 150A/dm2. On the other hand, two regions of surface brightness was found in a SRHS bath. One is region in the low temperature less than 25$^{\circ}C$ and the other in the moderate temperature range from 55$^{\circ}C$ to 65$^{\circ}C$.

• 한국재료학회지
• /
• 제29권11호
• /
• pp.720-726
• /
• 2019

Recently, research on cost reduction and efficiency improvement of crystalline silicon(c-Si) photovoltaic(PV) module has been conducted. In order to reduce costs, the thickness of solar cell wafers is becoming thinner. If the thickness of the wafer is reduced, cracking of wafer may occur in high temperature processes during the c-Si PV module manufacturing process. To solve this problem, a low temperature process has been proposed. Conductive paste(CP) is used for low temperature processing; it contains Sn57.6Bi0.4Ag component and can be electrically combined with solar cells and ribbons at a melting point of $150^{\circ}C$. Use of CP in the PV module manufacturing process can minimize cracks of solar cells. When CP is applied to solar cells, the output varies with the amount of CP, and so the optimum amount of CP must be found. In this paper, in order to find the optimal CP application amount, we manufactured several c-Si PV modules with different CP amounts. The amount control of CP is fixed at air pressure (500 kPa) and nozzle diameter 22G(outer diameter 0.72Ø, inner 0.42Ø) of dispenser; only speed is controlled. The c-Si PV module output is measured to analyze the difference according to the amount of CP and analyzed by optical microscope and Alpha-step. As the result, the optimum amount of CP is 0.452 ~ 0.544 g on solar cells.

• 한국결정성장학회지
• /
• 제18권6호
• /
• pp.232-236
• /
• 2008

최근 실리콘 원료의 부족에 따른 가격상승으로 인하여 99.9999% 이상의 순도를 지닌 폴리 실리콘을 더 저렴하게 제조하기 위한 연구가 활발히 진행되고 있다. 본 연구에서는 순도 99%의 금속급 실리콘(MG-Si)을 원료로 산처리와 일방향 응고를 통해 고순도로 정제하는 연구를 수행하였다. MG-Si 럼프를 플레너터리 밀로 분쇄한 후 HCl/$HNO_3$/HF 산 수용액에서 처리하였다. 그 결과 Al, Fe, Ca, Mn 등과 같은 금속 불순물들의 실리콘 내 함량이 크게 감소하면서 실리콘의 순도는 99.995%까지 향상되었다. 정제된 실리콘 분말을 성형한 후 HEM로를 이용하여 용융시킨 뒤, 일방향 응고를 통하여 잉곳을 제조하였다. 성장시킨 다결정 실리콘 잉곳은 $0.3{\Omega}{\cdot}cm$의 비저항과 $3.8{\mu}{\cdot}sec$의 열 운반자 소멸시간(minority carrier life time)을 나타내었다.

• Asian Journal of Atmospheric Environment
• /
• 제6권2호
• /
• pp.83-95
• /
• 2012

China has been a top producer and exporter of refined lead products in the world since the year 2000. After the phasing-out of leaded gasoline in the late 1990s, non-ferrous metallurgy and coal combustion have been identified as potential major sources of aerosol lead in China. This paper presents the single particle analytical results of ambient aerosol particles collected near a lead smelter using a scanning electron microscopy- energy dispersive x-ray spectroscopy (SEM-EDX). Aerosol particle samples were collected over a 24-hour period, starting from 8 pm on 31 May 2002, using a high volume TSP sampler. For this near source sample, 73 particles among 377 particles analyzed (accounting for 19.4%) were lead-containing particles mixed with other species (S, Cl, K, Ca, and/or C), which probably appeared to be from a nearby lead smelter. Lead-containing particles of less than $2{\mu}m$ size in the near source sample were most frequently encountered with the relative abundances of 42%. SEM-EDX analysis of individual standard particles, such as PbO, PbS, $PbSO_4$, $PbCl_2$, and $PbCO_3$, was also performed to assist in the clear identification of lead-containing aerosol particles. Lead-containing particles were frequently associated with arsenic and zinc, indicating that the smelter had emitted those species during the non-ferrous metallurgical process. The frequently encountered particles following the lead-containing particles were mineral dust particles, such as aluminosilicates (denoted as AlSi), $SiO_2$, and $CaCO_3$. Nitrate- and sulfate-containing particles were encountered frequently in $2-4{\mu}m$ size range, and existed mostly in the forms of $Ca(NO_3,SO_4)/C$, $(Mg,Ca)SO_4/C$, and $AlSi+(NO_3,SO_4)$. Particles containing metals (e.g., Fe, Cu, and As) in this near source sample had relative abundances of approximately 10%. Although the airborne particles collected near the lead smelter contained elevated levels of lead, other types of particles, such as $CaCO_3$-containing, carbonaceous, metal-containing, nitrates, sulfates, and fly-ash particles, showed the unique signatures of samples influenced by emissions from the lead smelter.

• 한국환경복원기술학회지
• /
• 제22권6호
• /
• pp.41-61
• /
• 2019

The purpose of this study was carried out to present the basic data for constructing a ecological stream, Shindangcheon stream located in Gyeongju-si, Gyeongsangbuk-do, South Korea. From August 2017 to June 2019, a total of 7 surveys were conducted. The numbers of vascular plants were summarized as 388 taxa including 75 families, 246 genera, 360 species, 4 subspecies, 19 varieties, 2 forms and 3 hybrids. The most families of taxa were Poaceae (59 taxa), Asteraceae (47 taxa), Fabaceae (27 taxa), Rosaceae and Cyperaceae (20 taxa, respectively), and Polygonaceae and Brassicaceae (15 taxa, respectively). The rare plant was Aristolochia contorta Bunge, and the Korean endemic plants were 4 taxa, such as Populus × tomentiglandulosa T.B.Lee, Salix koriyanagi Kimura ex Goerz, Lespedeza maritima Nakai, and Weigela subsessilis (Nakai) L.H.Bailey. The specific plants by floristic region found in this site were 13 taxa comprising 8 taxa of grade I, 4 taxa of grade III, and 1 taxon of grade IV. The naturalized plants were 73 taxa, such as Fallopia dumetorum (L.) Holub, Persicaria orientalis (L.) Spach., Potentilla supina L. var. ternata Pterm., and so forth. The invasive alien plants were 6 taxa, such as Rumex acetosella L., Sicyos angulatus L., Solanum carolinense L., Ambrosia artemisiifolia L., Lactuca serriola L., and Symphyotrichum pilosum (Willd.) G.L.Nesom..

• 한국분무공학회지
• /
• 제19권1호
• /
• pp.9-14
• /
• 2014

Performance of DI diesel engine with high-pressure fuel injection equipment is directly related to its emission characteristics and fuel consumption. So, the electro-hydraulic injector for the common-rail injection system should be designed to meet the precise high fuel delivery control capability. Currently, most high pressure injector in use has a needle driven by the solenoid coil energy or the piezo actuator controlled by charge-discharge of output pulse current. In this study, macroscopic spray approaching method was applied under constant volume chamber to research the performance of three different injectors : solenoid, indirect-acting piezo and direct-acting piezo type for CR direct-injection. LED back illumination for Mie scattering was applied on the liquid spray visible of direct-acting piezo injector, including hydraulic-servo type solenoid and piezo-driven injectors. As main results, we found that a direct-acting piezo injector had better a spray tip penetration than hydraulic-servo injectors in spray visualization.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2003년도 하계학술대회 논문집 C
• /
• pp.1496-1498
• /
• 2003

The $(Sr_{0.85}Ca_{0.15})TiO_3$(SCT) thin films were deposited on Pt-coated electrode (Pt/TiN/$SiO_2$/Si) using RF sputtering method according to the deposition condition. The optimum conditions of RF power and Ar/$O_2$ ratio were 140[W] and 80/20, respectively. Deposition rate of SCT thin films was about 18.75[${\AA}/min$] at the optimum condition. The capacitance characteristics had a stable value within ${\pm}4[%]$. The drastic decrease of dielectric constant and increase of dielectric loss in SCT thin films were observed above 200[kHz].