• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.7 no.2
• /
• pp.276-283
• /
• 1997

A dry impregnation method was used for preparing pellet type Pt/$SnO_2$ gas sensor. The crystal structure, direction of the crystal, crystal size and microstructure between the catalyst and the support ($SnO_2$) were characterized with electron diffraction analysis, transmission electron microscopy, scanning electron microscopy. The characterization indicates that when Pt/$SnO_2$ sample is calcined at $400^{\circ}C$, the Cl content associated with the Pt phase diminishes and the part of Pt is moved into $SnO_2$ support. This results in the enhancement of gas sensitivity. After the reactor with a Pt/$SnO_2$ sample was run with a flow rate of 30 sccm (a mixture of 0.5% $H_2$ in $_N2$) for a while, the resistance of $SnO_2$ was saturated, but the $SnO_2$ kept absorbing $H_2$ gas. This indicates that the surface state was saturated. For the 14 ppm $H_2$ gas, the sensitivity of Pt/$SnO_2$ devices was about 81% at an operating temperature of $300^{\circ}C$.

• Proceedings of the KIEE Conference
• /
• 2003.07c
• /
• pp.1410-1412
• /
• 2003

PTC 자기발열기판을 사용해서 저전력 방폭형 CO센서를 제작하고 그 특성을 고찰하였다. CO가스센서의 감지특성을 향상시키기 위하여 Pt가 island 형상을 갖는 다층 Pt/$SnO_2$ 박막구조를 도입하였으며, 이와 같은 구조는 Pt/$SnO_2$ 위에 다시 $SnO_2$ 및 Pt cluster 층들을 연속적으로 증착함으로서 제작되었다. 200ppm의 CO가스농도에서 측정된 다층 $Pt/SnO_2$박막 센서의 감도는 1.72($R_{air}/R_{CO}$)로, 단충 Pt/$SnO_2$ 박막 센서의 최대감도(1.23)보다 훨씬 더 높았다 이것은 Pt와 $SnO_2$사이의 계면적 증대에 기인하는 것으로 생각된다. 제작된 Pt/$SnO_2$ 가스센서의 평균 소비전력은 38.5mW이며, 측정농도범위($30{\sim}1,000ppm$)에서 매우 양호한 감지특성을 나타내었다.

• Proceedings of the International Microelectronics And Packaging Society Conference
• /
• 2003.11a
• /
• pp.76-79
• /
• 2003

본 실험에서는 $S0.7wt\%Cu,\;Sn3.8wt\%Ag0.7wt\%Cu$ solder와 금속층으로서의 좋은 특성을 가지고 있지만 아직 연구 보고 된 적 없는 Pt층과의 리플로 반응에 의해 형성되는 계면금속간화합물의 상 분석을 시도 하였다 또한 솔더내 Cu함량에 따른 계면금속간화합물의 변화에 대하여 연구하기 위해 $Sn1.7wt\%Cu$솔더와 Pt층의 계면반응 현상에 대한 연구도 수행하였다. $Sn0.7(1.7)wt\%Cu$솔더는 순수한 Sn과 Cu를 이용하여 중량비로 제조하였고, $Sn3.8wt\%Ag0.7wt\%Cu$솔더는 솔더페이스트를 사용하였다. 분석은 SEM, EDS, XRD를 이용하였다. 분석 결과 세 가지 무연솔더 모두에서 $PtSn_4$가 계면 금속간화합물로 존재함을 발견하였으며 $1.7wt\%Cu$를 포함한 솔더와 Pt와의 반응에서는 고용도 이상으로 첨가된 Cu에 의해 솔더 내부에 조대한 형상의 $Cu_6Sn_5$가 존재함을 SEM 및 EDS분석을 통하여 발견 하였다.

• Clean Technology
• /
• v.19 no.3
• /
• pp.320-326
• /
• 2013

Nano-sized PtRu-Ni/VC and PtRu-Sn/VC electrocatalysts were synthesized by a one-step radiation-induced reduction (RIR) (30 kGy) process using distilled water as the solvent and Vulcan XC-72 as the supporting material. The obtained electrocatalysts were characterized by transmission electron microscopy (TEM), scanning electron microscope energy dispersive spectroscopic (SEM-EDS), X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS), respectively. The catalytic efficiency of electrocatalysts was examined for oxygen reduction, MeOH oxidation and CO stripping decreased in the following order, Hydrogen stripping : PtRu-Sn/VC > PtRu-Ni/VC > PtRu/VC$^{(R)}$ (E-TEK). MeOH oxidation : PtRu-Sn/VC > PtRu-Ni/VC > PtRu/ VC$^{(R)}$ (E-TEK). Unit cell performance : PtRu-Sn/VC > PtRu-Ni/VC > PtRu/VC$^{(R)}$ (E-TEK) catalysts.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.5 no.1
• /
• pp.83-86
• /
• 2004

A high temperature tolerant microelectronic-based carbon monioxde(CO) gas sensor has been developed. The gas sensing performance has been studied over a wide temperature range$(100-300^\circ{C)}$. The gas sensitivity of the sensor is high, its initial sensing behavior is very fast, and the sensor is reproducible. Pt-SiC and $Pt-SnO_2-SiC$ diodes are fabricated using standard semiconductor processes and their CO gas-sensing behaviors are analyzed as a function of CO gas concentration and temperature by I-V and $\Delta{I-t}$ methods under steady-state and transient conditions. The sensitivity of the device with $Pt-SnO_2$ catalytic gate is higher than that of the Pt gate. The experimental results indicate that $SnO_2$ layer improves the catalytic reaction of the Pt layer.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.25 no.11
• /
• pp.1315-1322
• /
• 1988

$SnO_X$/Pt thin film gas sensors were fabricated and their performance characteristics were measured. The $SnO_X$/Pt films were deposited by vacuum evaporating the $SnO_2$ target mixed with 2 wt% Pt. The conductivity showed the temperature dependence and the sensitivity to CO gas was proportional to the square root of gas concentration below 2000 ppm. The optimum operating temperature of the fabricated devices was about 300$^{\circ}$C and the response time in 5000 ppm CO gas was about 20 sec.

• Electrical & Electronic Materials
• /
• v.9 no.1
• /
• pp.38-43
• /
• 1996

A coprecipitation method was used for preparing Ca and Pt doped $SnO_2$ fine powder. Components of the powder were investigated by XPS and SIMS. Crystallite size and specific surface area were investigated by TEM, XRD, and BET analysis. $SnO_2$(Ca)/Pt based thick film devices were prepared by a screen printing technique for methane gas detection. Then sensing characteristics of the devices were investigated. As Ca and Pt added, the crystal growth of $SnO_2$ was suppressed during calcining and sintering, and the sensitivity of $SnO_2$(Ca)/Pt thick film to methane gas was enhanced. For the Pt doped $SnO_2$ fine particle, the thick film device shows sensitivity of about 83% to 2000 ppm methane gas at an operating temperature of >$400^{\circ}C$.

• Applied Chemistry for Engineering
• /
• v.21 no.5
• /
• pp.537-541
• /
• 2010

Pt-Sn with various ratios was supported on carbon black after pretreatment in an acidic solution by a reduction method. The Pt/Sn ratio was controlled by varying the concentration of each component in the solution, and the influence of the composition on the electrocatalytic activities was investigated. The crystallinity of the synthesized materials was investigated by XRD (X-ray Diffraction), and the oxidation states of both the platinum and tin were determined by XPS (X-ray Photoelectron Spectroscopy). SEM (Scanning Electron Microscopy)-EDS (Energy Dispersive Spectroscopy) was utilized to examine the morphology and composition of the synthesized electrode, and the particle size of the Pt-Sn was analyzed by TEM (Transmission Electron Microscopy). The electrocatalytic activity for oxygen reduction was evaluated in a 0.5 M $H_2SO_4$ solution using a rotating disk electrode system. The activity and stability were found to be strongly dependent on the electrode composition (Pt/Sn ratio). The catalytic activity and stability for methanol oxidation were also measured using cyclic voltammetry (CV) in a mixture of 0.5 M $H_2SO_4$ and 0.5 M $CH_3OH$ aqueous solution. The addition of proper amount of Sn was found to significantly improve both catalytic activity and stability for methanol oxidation.

• Proceedings of the KIEE Conference
• /
• 1997.07d
• /
• pp.1304-1307
• /
• 1997

A hydrogen gas sensor utilizing Pt/$SnO_2$ system was fabricated by the pressed pellet method. The crystal structure, direction of the crystal, crystal size and microstructure between the catalyst and the support ($SnO_2$) were characterized with Electron Diffraction Analysis, Transmission Electron Microscopy, Scanning Electron Microscopy. After the reactor with a Pt/$SnO_2$ sample was run with a flow rate of 30sccm (a mixture of $0.5%H_2$ in $N_2$) for a while, the resistance of $SnO_2$ was saturated, but the $SnO_2$ kept absorbing $H_2$ gas. $H_2$ gas sensing properties of Pt/$SnO_2$ were investigated at several temperatures. As a result, it was observed that Pt/$SnO_2$ has high sensitivity at $300^{\circ}C$ and $400^{\circ}C$.

• Proceedings of the Korean Environmental Sciences Society Conference
• /
• 2008.11a
• /
• pp.464-467
• /
• 2008

성능이 우수한 다성분계 전극을 개발하기 위하여 Pt, Ru, Sn, Sb 및 Gd의 5 종류 금속을 이용하여 1성분계 전극의 성능과 산화제 생성량 및 2성분계 전극의 성능과 산화제 생성 경향을 고찰하여 다음의 결과를 얻었다. 1. RhB 농도 감소는 Ru/Ti > Sb/Ti > Pt/Ti > Sn/Ti > Gd/Ti 전극의 순서로 나타났으나 단위 전력당 2분간 제거된 RhB 농도 감소는 Ru/Ti > Sb/Ti > Pt/Ti > Gd/Ti > Sn/Ti 전극의 순서로 나타났다. 생성된 산화제 농도는 ClO$_2$ > free Cl > H$_2$O$_2$ > O$_3$의 순서였으며 Gd/Ti 전극의 경우 산화제가 거의 생성되지 않는 것으로 나타났다. 모든 전극에서 OH 라디칼이 거의 생성되지 않는 것으로 나타났다. Ru/Ti와 Sb/Ti 전극의 높은 RhB 분해와 산화제 생성 농도는 정확하지는 않지만 상관관계가 있는 것으로 나타났다. 2. Ru계 2성분 전극(Ru-Gd/Ti, Ru-Pt/Ti, Ru-Sn/Ti 및 Ru-Sb/Ti)은 모두 1성분계 전극보다 RhB 분해성능이 높아지는 것으로 나타났으며, Ru계 2성분 전극 중 가장 성능이 우수하였던 전극은 Ru:Sn=9:1 전극으로 나타났다. Sn-Sb/Ti 전극은 Sn:Sb=1:9의 전극 성능이 우수한 것으로 나타났으나 Sb/Ti 전극과의 차이는 크지 않은 것으로 나타났다. Pt계 전극(Pt-Gd/Ti, Pt-Sn/Ti, Pt-Sb/Ti)은 대체로 두 성분 혼합에 따른 RhB 분해효과 상승은 없는 것으로 나타났다. 2성분계 전극 중 RhB 제거 성능이 가장 우수하였던 Ru:Sn=9:1 전극에서 4종류의 산화제 생성 농도가 높은 것으로 나타났다. Ru:Pt=9:1 전극은 RhB 분해 성능이 5 전극 중 가장 낮았으며, 산화제도 생성량이 가장 적은 것으로 나타났다. Ru-Sn/Ti 계 전극의 RhB 분해 성능과 산화제 생성 농도가 실험한 모든 1, 2성분계 전극에서 높은 것으로 나타나 향후 3, 4성분계 전극 제조시 이를 바탕으로 제조하고 다른 물질들은 보조재료로서 사용할 필요성이 있는 것으로 사료되었다.