• Journal of the Microelectronics and Packaging Society
• /
• v.22 no.2
• /
• pp.55-59
• /
• 2015

Novel low-volume solder-on-pad (SoP) process is proposed for a fine pitch Cu pillar bump interconnection. A novel solder bumping material (SBM) has been developed for the $60{\mu}m$ pitch SoP using screen printing process. SBM, which is composed of ternary Sn-3.0Ag-0.5Cu (SAC305) solder powder and a polymer resin, is a paste material to perform a fine-pitch SoP in place of the electroplating process. By optimizing the volumetric ratio of the resin, deoxidizing agent, and SAC305 solder powder; the oxide layers on the solder powder and Cu pads are successfully removed during the bumping process without additional treatment or equipment. The Si chip and substrate with daisy-chain pattern are fabricated to develop the fine pitch SoP process and evaluate the fine-pitch interconnection. The fabricated Si substrate has 6724 under bump metallization (UBM) with a $45{\mu}m$ diameter and $60{\mu}m$ pitch. The Si chip with Cu pillar bump is flip chip bonded with the SoP formed substrate using an underfill material with fluxing features. Using the fluxing underfill material is advantageous since it eliminates the flux cleaning process and capillary flow process of underfill. The optimized interconnection process has been validated by the electrical characterization of the daisy-chain pattern. This work is the first report on a successful operation of a fine-pitch SoP and micro bump interconnection using a screen printing process.

• Journal of the Microelectronics and Packaging Society
• /
• v.29 no.2
• /
• pp.91-97
• /
• 2022

The wettability and rheological properties of solder paste with the size of the solder powder were evaluated. To formulate the solder paste, three types of solder powder were used: T4 (20~28 ㎛), T5 (15~25 ㎛), and T6 (5~15 ㎛). The viscosities of the T4, T5, and T6 solder pastes at 10 RPM were 155, 263, and 418 Pa·s, respectively. After 7 days, the viscosity of the T4 solder paste slightly increased by 2.6% and that of T5 was increased by 20.6%. The viscosity of the T6 solder paste after 7 days could not be measured due to high viscosity. The viscosity variation with solder particle size also affected on the printability of the solder. In the case of the T4 solder paste, printability, slump, bridging, and soldering properties were excellent. On the other hand, T5 showed slight dewetting and solder ball defects. Especially, T6, which the smallest powder size, showed poor printability and dewetting at the edge of solder.

• Journal of the Microelectronics and Packaging Society
• /
• v.26 no.3
• /
• pp.43-49
• /
• 2019

In this study, a new approach using graphene oxide (GO) powder-composited Sn-3.0Ag-0.5Cu(in wt.%) solder paste for improving the bending reliability of solder joints between a flexible substrate and small outline package (SOP) was suggested. The GO addition slightly affected the melting temperature, however, the change in the melting temperature was not significant. Meanwhile, we observed the addition of GO could suppress IMC growth and IMC thickness of solder joint during the reflow process. Moreover, the cyclic bending test was also performed for evaluation of reliability in solder joint and we could improve the cyclic bending reliability of solder joint by adding GO powders. For 0.2 wt.% of GO added to the solder joint, the bending lifetime was increased to 20% greater than that without GO. Pull strength and ductility of the solder joint with GO were also higher than those of the joint without GO and it was assumed that this effect by adding GO could contribute to improve cyclic bending reliability of solder joint.

• Proceedings of the KWS Conference
• /
• 2010.05a
• /
• pp.77-77
• /
• 2010

본 연구에서는 Sn-3.0Ag-0.5Cu (SAC305) 무연솔더의 최적 인쇄성을 위한 PCB 및 마스크설계, 스크린프린팅 공정변수의 최적값을 실험계획법을 통해 평가하였다. 사용된 칩은 가로 0.4mm 세로 0.2mm의 0402 MLCC칩이며, 사용된 시험보드는 OSP 표면처리된 PCB이었다. 인쇄성을 판단하기 위한 공정인자는 금속마스크 두께, 마스크홀 크기, 패드크기 및 모양, 인쇄각도, 인쇄속도, 판분리속도이었다. ANOVA분석을 통해 주인자를 파악하였으며, 인쇄성에 영향을 미치는 주인자는 마스크두께와 인쇄각도임이 확인되었다. 그 후 중심 합성법을 이용하여 인쇄성 최적 조건을 확인하였다. 결과로 나타난 등고선/표면도를 통해, 마스크두께가 작을 때에는 인쇄각도가 작아야 높은 인쇄성을 갖으며, 또한 마스크 두께가 클 경우에는 인쇄각도가 커야 높은 인쇄성을 가짐을 알 수 있었다. 추가실험을 통해서 인쇄성 표면도의 정확도를 확인하였으며, 실험값은 표면도에서 표시된 인쇄성값과 비슷함을 알 수 있었다. 또한, 인쇄성이 낮은 영역과 높은 영역에서 접합강도값을 측정하였으며, 인쇄성이 좋은 영역에서 접합강도도 높음을 알 수 있었다.