• Korean Journal of Breeding Science
• /
• v.43 no.2
• /
• pp.139-144
• /
• 2011

Fifty-five sweet pepper (Capsicum annuum L.) germplasm from the Rural Development Administration (RDA) were analyzed for their fruit yield and fruit quality characters, including fruit weight, fruit size, pericarp thickness, total soluble content, fruit lobe, fruit shape, fruit surface and fruit color. Fruit yield per plot ranged from 200 g to 8150 g (average, 1884 g). Fruit fresh-weight per fruit ranged from 27.3 g to 200.0 g with an average of 97.2 g. Fruit length varied from 4.0 cm to 16.2 cm (average, 9.6 cm). Fruit length-to-width ratio ranged from 0.6 to 3.0 with an average 1.7. The fruit pericarp thickness ranged from 1.8 mm to 10.7 mm (average, 4.8 mm). Total soluble content was the highest ($8.5^{\circ}Brix$) in K156286 and the lowest ($5.3^{\circ}Brix$) in K156208 with the average value $6.7^{\circ}Brix$. Fruit lobes numbers varied from 2 to 4. Blocky, triangular, elongated, rectangular and round fruit shape identified among the sweet pepper accessions. Fruit surface varied from smooth to wrinkle and fruit color also varied. The presence of variability in fruit yield and quality traits within the sweet pepper genotypes can be utilized to develop high yielding sweet pepper variety with better fruit quality characters.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.257.1-257.1
• /
• 2014

We investigated characteristics of ITO/Ag-Pd-Cu (APC)/ITO multilayer electrodes prepared by direct current magnetron sputtering for use as an anode in organic solar cells (OSCs). To optimize electrical properties of ITO/APC/ITO multilayer, we fabricated the ITO/APC/ITO multilayer at a fixed ITO thickness of 30 nm as a function of APC thickness. Compare to the surface of Ag layer on ITO, the APC had a smooth surface morphology. At optimized APC thickness of 12 nm, the ITO/APC/ITO multilayer exhibited a sheet resistance of $6{\Omega}/square$ and optical transmittance of 84.15% at a wavelength of 550 nm which is comparable to conventional ITO/Ag/ITO multilayer. However, the APC-based ITO multilayer showed a higher average transmittance in a visible region than the Ag-based ITO multilayer. The higher average transmittance of ITO/APC/ITO multilayer indicated the multilayer is suitable anode for organic solar cells with P3HT:PCBM active layer. OSCs fabricated on the optimized ITO/ACP/ITO multilayer exhibited a better performance with a fill factor of 64.815%, a short circuit current of $8.107mA/cm^2$, an open circuit voltage of 0.59 V, and power conversion efficiency (3.101%) than OSC with ITO/Ag/ITO multilayer (2.8%).

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2016.11a
• /
• pp.105-105
• /
• 2016

Recently, high power impulse magnetron sputtering (HIPIMS) has attracted considerable attentions due to its high potential for industrial applications. By pulsing the sputtering target with high power density and short duration pulses, a high plasma density and high ionization of the sputtered species can be obtained. HIPIMS has exhibited several merits such as increased coating density, good adhesion, microparticle-free and smooth surface, which make the HIPIMS technique desirable for synthesizing hard coatings. However, hard coatings present intrinsic defects (columnar structures, pinholes, pores, discontinuities) which can affect the corrosion behavior, especially when substrates are active alloys like steel or in a wear-corrosion process. Atomic layer deposition (ALD), a CVD derived method with a broad spectrum of applications, has shown great potential for corrosion protection of high-precision metallic parts or systems. In ALD deposition, the growth proceeds through cyclic repetition of self-limiting surface reactions, which leads to the thin films possess high quality, low defect density, uniformity, low-temperature processing and exquisite thickness control. These merits make ALD an ideal candidate for the fabrication of excellent oxide barrier layer which can block the pinhole and other defects left in the coating structure to improve the corrosion protection of hard coatings. In this work, CrN/Al2O3/CrN multilayered coatings were synthesized by a hybrid process of HIPIMS and ALD techniques, aiming to improve the CrN hard coating properties. The influence of the Al2O3 interlayer addition, the thickness and intercalation position of the Al2O3 layer in the coatings on the microstructure, surface roughness, mechanical properties and corrosion behaviors were investigated. The results indicated that the dense Al2O3 interlayer addition by ALD lead to a significant decrease of the average grain size and surface roughness and greatly improved the mechanical properties and corrosion resistance of the CrN coatings. The thickness increase of the Al2O3 layer and intercalation position change to near the coating surface resulted in improved mechanical properties and corrosion resistance. The mechanism can be explained by that the dense Al2O3 interlayer acted as an excellent barrier for dislocation motion and diffusion of the corrosive substance.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.31 no.7
• /
• pp.437-442
• /
• 2018

This work reports the preparation of Al-Ti based oxide thin films and their optical properties. Although the transmittance of a $TiO_2/Al2O_3$ bilayer structure was as high as 90% at wavelengths of 600 nm or larger, the reflectance of the bilayer reached its minimum at wavelengths of around 360 nm. The transmittance of an 89-nm-thick $TiO_2$ thin film rapidly increased and then decreased at a critical wavelength because of destructive interference. The wavelength corresponding to the reflectance minimum increased after an increase in $TiO_2$ film thickness. The smooth surface morphology of the AlTiO thin film was retained up to a film thickness of 65 nm, and the transmittance of the film was inversely proportional to film thickness, in accordance with the general tendency for optical films. The reflectance of the AlTiO film at visible light wavelengths was lower than that of the $TiO_2$ film, which implies that the AlTiO film is suitable for applications as an optical thin film layer in semitransparent solar cells.

• Journal of the Korea Society for Simulation
• /
• v.16 no.1
• /
• pp.21-29
• /
• 2007

In this paper, we present a method of detecting the boundary of the intima-media complex for automated measurement based on dynamic programming from carotid artery B-mode ultrasound images and then show the experimental results. We apply the dynamic programming for determining the optimal locations that a cost function is minimized. The cost function includes cost terms which are representing image features such as intensity, intensity gradient and geometrical continuity of the vessel interfaces. Moreover, we improve the boundary continuity by applying the B-spline to smooth the rough boundary due to noise such as speckle, dropout and weak edges. The proposed method has obtained more accurate reproducible results than conventional edge-detection by considering multiple image features and ensures efficient automated measurement by solving the problems of the inter- and intra-observer variability and its inefficiency due to manual measurement.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.30 no.8
• /
• pp.469-473
• /
• 2017

We investigated the effect of different thin-film thicknesses (25, 30, and 40 nm) on the electrical performance of solution-processed indium-zinc-oxide (IZO) thin-film transistors (TFTs). The structural properties of the IZO thin films were investigated by atomic force microscopy (AFM). AFM images revealed that the IZO thin films with thicknesses of 25 and 40 nm exhibit an uneven distribution of grains, which deforms the thin film and degrades the performance of the IZO TFT. Further, the IZO thin film with a thickness of 30 nm exhibits a homogeneous and smooth surface with a low RMS roughness of 1.88 nm. The IZO TFTs with the 30-nm-thick IZO film exhibit excellent results, with a field-effect mobility of $3.0({\pm}0.2)cm^2/Vs$, high Ion/Ioff ratio of $1.1{\times}10^7$, threshold voltage of $0.4({\pm}0.1)V$, and subthreshold swing of $0.7({\pm}0.01)V/dec$. The optimization of oxide semiconductor thickness through analysis of the surface morphologies can thus contribute to the development of oxide TFT manufacturing technology.

• Journal of the Korean institute of surface engineering
• /
• v.53 no.6
• /
• pp.351-359
• /
• 2020

Formation behavior and properties of PEO (Plasma Electrolytic Oxidation) film on AA2024 were investigated under application of pulsed current as a function of Na3PO4 concentration in 0.05 M Na2SiO3 solution by analyzing voltage-time behavior, in-situ observation of arc generation, observation of surface morphology and measurements of thickness and surface roughness. Arc generation voltage decreased with increasing Na3PO4 concentration. Color difference of PEO films between edge and inner part disappeared by addition of Na3PO4. It was also observed that size of nodules on PEO film decreased with increasing Na3PO4 concentration. Thickness of PEO films formed on AA2024 increased with increasing Na3PO4 concentration. Whereas, surface roughness of PEO films decreased with increasing Na3PO4 concentration up to 0.05 M of Na3PO4 which is attributed to the deceased size of nodules on the PEO films. However, the surface roughness increased with increasing Na3PO4 concentration more than 0.07 M of Na3PO4 which seems to be due to the formation of non-uniform PEO films with smooth surface and large size pores formed by orange-colored big arcs. The experimental results suggest that added sodium phosphate less than 0.2 M in an alkaline silicate solution can contribute to the formation of relatively thick and uniform thickness of PEO films under arc generation voltage lower than 300 V.

• The Journal of Korean Academy of Prosthodontics
• /
• v.45 no.5
• /
• pp.675-686
• /
• 2007

Statement of problem: Titanium nitride(TiN) coatings are the most general and popular coating method and used to improve the properties of metallic surface for industrial purposes. When TiN coating applied to the abutment screw, frictional resistance would be reduced, as a results, the greater preload and prevention of the screw loosening could be expected. Purpose: The purpose of this study was to investigate mechanical properties of TiN coated film of various coating thickness on the titanium alloy surface and to evaluate proper coating thickness. Material and method: 95 Titanium alloy (Ti-6Al-4V) discs of 15 mm in diameter and 3 mm in thickness were prepared for TiN coating and divided into 7 groups in this study. Acceding to coating deposition time (CDT) with TiN by using Arc ion plating, were divided into 7 groups : Group A (CDT 30min), Group B (CDT 60min), Group C (CDT 90min), Group D (CDT 120min), Group E (CDT 150min), Group F(CDT 180min) and Group G (no CDT) as a control group. TiN coating surface was observed with Atomic Force Microscope(AFM), field emission scanning electron microscopy(FE-SEM) and examined with scratch tester, wear tester. Result: 1. Coating thickness fir each coated group was increased in proportion to coating deposition time. 2. Surface of all coated groups except Group A was homogeneous and smooth. However, surface of none coated Group G had scratch. 3. Adhesion strength for each coated group was increased in proportion to coating deposition time. 4. Wear resistance for each coated group was increased in proportion to coating deposition time. 5. Surface roughness in Group A, B, C was increased in proportion to coating deposition time. But, surface roughness in Group D, E, F was showed decreased tendency in proportion to coating deposition time. Conclusion: According to coating deposition time, mechanical properties of TiN coated film were changed. It was considered that 120 minutes coating deposition time ($1.32{\mu}m$ in coating thickness) is necessary.

• Korean Journal of Materials Research
• /
• v.14 no.1
• /
• pp.1-8
• /
• 2004

Laser weldability of aluminized steels for deep drawing application has been investigated. Test coupons for Nd:YAG laser welding and $CO_2$ laser welding were prepared trom the commercial steels. According to the test results, total penetration and back bead width of aluminized steels were sensitive to the welding conditions. Bead width at the half thickness of the overlap joint, however, was rather constant. Laser weldability of aluminized steels was superior to that of zinc coated steel. Weld microstructure revealed that overlap zone adjacent to the fusion line was filled with coated materials, which was thought to be desirable to protect weld from crevice corrosion. The aluminum coated materials was also found in the weld metal. Practically no spattering was observed in the laser welding of aluminized steels even when the welding was performed without joint gap. In the welding of zinc coated steel, however, spattering was so severe that it was difficult to get the acceptable weld. Bead quality of aluminized steel laser weld was smooth and stable.

• Korean Journal of Materials Research
• /
• v.14 no.8
• /
• pp.579-586
• /
• 2004

A study on the effects of oxide growth on the mechanical properties degradation of pure zirconium and Zircaloy-4 is carried out with high temperature tensile tests. It is found that the mechanical properties can deteriorate with the oxide growth less than $1\%$ of total specimen cross section, especially at $300\~400^{\circ}C$ that is zirconium alloy cladding temperature during the nuclear reactor operation. It is also revealed that Young's modulus changes little but yield strength and tensile strength drop down to $20\% and 40\%$ of the room temperature strength, respectively, in the temperature range. Fractographic analysis shows that the number of dimples decreases and fractured surface becomes smooth with increasing oxide thickness.