• 전기학회논문지
• /
• 제63권10호
• /
• pp.1402-1411
• /
• 2014

In this paper, the Maximum Power Point Tracking(MPPT) control of the small scale wind power generation system with a three-phase diode rectifier and the grid-connected inverter is studied. Without the need for the converter circuits to control speed of the generator, it is economical and the structure is simple. Compared with existing systems, it can be to reduce the power semiconductor switches and passive elements, and to implement the MPPT control with only DC-Link voltage control of the grid-connected inverter. In order to allow MPPT control without the characteristic information of the wind turbine, the P&O algorithm is applied, and these are verified by the simulation and experiment.

• 전기학회논문지
• /
• 제66권4호
• /
• pp.605-612
• /
• 2017

One of the biggest environmental issues that our world has been facing is climate change. In order to cope with such environmental issues, the world is putting a great deal of effort into energy conservation. The building sector, in particular, consumes 36% of the energy consumed worldwide and emits considerable amount of greenhouse gases. Therefore, introduction of renewable energies in the building sector is highly recommended. Renewable energy sources that can be utilized in the building sector include sunlight, solar heat, geothermal heat, fuel cells and wind power. The wind power generation system which converts wind energy into electrical energy has advantages in that wind is an unlimited and pollution-free resource. It is suitable to be connected to existing buildings because many years of operational experience and the enhanced stability of the system have made it possible to downsize the electrical generator. In case of existing buildings, it is necessary to consider the live loads of the buildings to connect the wind power generation system. This paper, through the connection of the wind power generation with existing buildings, promotes reduction of greenhouse gas emissions and energy independence by reducing energy consumption in the building sector. In order to connect the wind power generation system with an exciting building, the live load of the building and the area of the rooftop should be considered. The installable model is selected by comparing the live load of the building and the load of the wind power generation system. The maximum number of the wind turbines that can be installed is obtained by considering the separation distance between the wind turbines within the area of the rooftop. Installations are divided into single installations and multiple installations of two different types of wind turbines. After determining the maximum installable number, the optimal model that can achieve the maximum annual power generation will be selected by comparing the respective total annual amount of the power generation of different models.

• Journal of Magnetics
• /
• 제17권1호
• /
• pp.33-35
• /
• 2012

A magnetic brake system was fabricated for use with small wind turbines. The torque of the pivot did not change as the speed of revolution increased when the magnetic array disc was far from the salient of the aluminum housing, the torque abruptly increased as the magnetic array approached the salient of the aluminum housing. The torque increased as a quadratic function of the speed of revolution when the distance between the magnetic array and the datum point was 60 mm.

• 전기학회논문지
• /
• 제60권6호
• /
• pp.1128-1133
• /
• 2011

In a wind farm, a large number of small wind turbine generators (WTGs) operate whilst a small number of a large generator do in a conventional power plant. To maintain high quality and reliability of electrical energy, a wind farm should have equal performance to a thermal power plant in the transient state as well as in the steady state. The wind farm shows similar performance to the conventional power plant in the steady state due to the advanced control technologies. However, it shows quite different characteristics during fault conditions in a grid, which gives significant effects on the operation of a wind farm and the power system stability. This paper presents an analysis of response of a wind farm during grid fault conditions. During fault conditions, each WTG might produce different frequency components in the voltage. The different frequency components result in the non-fundamental frequencies in the voltage and the current of a wind farm, which is called by "beats". This phenomenon requires considerable changes of control technologies of a WTG to improve the characteristics in the transient state such as a fault ride-through requirement of a wind farm. Moreover, it may cause difficulties in protection relays of a wind farm. This paper analyzes the response of a wind farm for various fault conditions using a PSCAD/EMTDC simulator.

• 조명전기설비학회논문지
• /
• 제25권6호
• /
• pp.42-48
• /
• 2011

Generally, the structure without the stator core Axial Field Permanent Magnet (AFPM) generator was simple and there was nearly no cogging toque. And because it had the wide driving rate area, it had been being mainly used in the small wind power generation system. However, AFPM generator with non-slotted stator can't generate high voltage at low wind speed due to long air-gap. It is the reason of output efficiency drop. Therefore, in this paper, the AFPM synchronous generator with internal rotor and dual slotted stators for the small wind turbine is studied, and deal with a cogging torque minimization through the determination of optimum pole-arc ratio.

• 해양환경안전학회지
• /
• 제19권1호
• /
• pp.59-65
• /
• 2013

최근 몇 년간 에너지 위기에 대한 우려가 급격히 증가하고 있으며, 방대한 에너지소비에 따른 환경오염도 큰 문제로 대두되고 있다. 사회적으로 에너지 위기가 고조되고 있는 가운데 새로운 에너지나 신재생에너지에 대한 관심이 증가하고 있다. 본 연구는 이러한 문제를 해결하기 위한 하나의 해결책으로 양어장 등에서 사용되는 폭기장치를 구동하기 위한 에너지를 자연으로부터 얻을 수 있는 가능성을 타진해 본 연구이다. 연구의 목적은 풍력에너지를 이용한 폭기장치의 개발에 있으며, 다양한 풍속 및 수풍면적에 대한 풍력폭기장치의 가능성을 살펴보고 있다. 또한, 최대의 효율을 얻을 수 있는 풍력펌프의 각도에 대한 토출구의 높이를 유도하여 유사한 장치의 설계에 있어 도움을 줄 수 있는 데이터를 제공하고 있다.

• Composites Research
• /
• 제22권1호
• /
• pp.22-31
• /
• 2009

최근 화석 연료가 고갈됨에 따라 대체 에너지 개발 연구가 활발히 진행되고 있다. 여러 대체 에너지들 중 풍력 발전기는 바람의 에너지를 전기적 에너지로 바꾸어 주는 시스템으로 매우 친환경적이기 때문에 다양하게 연구되고 있다. 따라서 본 연구의 목표는 500W급 소형 풍력 발전용 블레이드의 개발로서 외국에 비하여 상대적으로 풍속이 낮은 국내와 같은 지역에 적용할 수 있도록 설계 되어야 한다. 본 논문에서는 피로수명을 고려한 고효율 경량화 블레이드의 공력설계 및 구조설계 방법이 제안되었으며, 구조해석으로 선형 정적해석, 좌굴해석, 진동모드해석이 수행되었다. 또한 풍력 발전 시스템에 발생할 수 있는 유체충돌해석을 모사하였다. 해석결과들은 유압시험장비를 이용한 구조시험 빛 성능시험의 결과와 비교되었고, 비교적 잘 일치하여 설계결과의 안전성을 확인하였다.

• 대한기계학회논문집A
• /
• 제36권9호
• /
• pp.1087-1094
• /
• 2012

본 논문에서는 구조 시험과 유한요소해석을 통하여 소형 풍력발전용 복합재 블레이드의 구조적 안전성을 평가하였다. 먼저, 선행연구에서 공력해석을 수행하여 정격 및 극한 풍속일 때의 블레이드가 받는 굽힘 모멘트를 산출하였다. 이를 이용하여 소형풍력발전기 관련 국제 규격인 IEC 61400-2에 따른 실규모 구조 시험을 수행하여 구조적 안전성을 평가하였다. 그리고 유한요소법을 이용한 구조 해석을 수행하여 구조 시험 결과와 비교하여 이의 정확성을 판단하였다. 또한, 구조 시험을 통해 블레이드에 대한 과잉 설계가 확인되었으며 이의 해결을 위하여 블레이드의 적층 순서 및 두께를 재선정하여 구조적 안전성을 평가하였다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2009년도 제40회 하계학술대회
• /
• pp.830_831
• /
• 2009

Wind power system attracts most interest because of high-energy efficiency with environment-friendly. Small scale wind power applications requires a cost effective and mechanically simple generator in order to be a reliable energy source. The use of direct driven generators, instead of geared machines, reduces the number of drive components, which offers the opportunity to reduce costs and increases system reliability and efficiency. This paper presents the development of a coreless axial-flux permanent magnet(AFPM) generator for a urban wind power system. It is analyzed by electromagnetic simulation program Maxwell 3D

• 한국태양에너지학회 논문집
• /
• 제33권6호
• /
• pp.70-76
• /
• 2013

Recently industrial control systems have been required to ensure intelligent, high tech automation, interconnection and interoperability demands. Therefore, there is a need to redefine the structure concepts of SCADA system for wind power. Also, at this time, the integrated management system is required for the distributed development of wind farms where are needed often interoperability features and exchange information between different wind farms, wind turbines or SCADA systems. In this paper, an integrated structural concepts for SCADA system are defined. Based on this definition of an integrated SCADA system, the basic designs are analyzed on physical layer, system layer and application layer which are corresponded to wind turbine controller, the SCADA server and the SCADA client, and implement HMI. Between the implementation SCADA server and the client, their normal functions were verified at the small scale wind energy test facilities.