• 대한기계학회논문집
• /
• 제12권6호
• /
• pp.1327-1334
• /
• 1988

본 연구에서는 회전굽힘응력하에서 비관통노치를 갖는 재료의 피로거동을 분 석하기 위하여 우선 시험편의 반지름에 해당한 심공노치를 갖는 시험편을 준비하고 이 시험편이 고, 중간, 저응력을 받는경우 작용응력의 대소에 의한 표면 및 내부크랙전파 특성과 함께 크랙면형상변화 관계를 검토하였다.

• 대한기계학회논문집
• /
• 제11권3호
• /
• pp.355-361
• /
• 1987

본 연구에서는 고온기기의 부재로 널리 사용되는 304스테인리스강을 사용하여 기기의 사용조건을 고려한 538.deg. C(1000.deg. F), 593.deg. C(1100.deg. F)및 650.deg. C(1200.deg. F)의 세가지 온도레벨하의 대기중에서 크리이프-피로시험을 실시하여 작은 인공표면결함으로부터 발생.성장하는 표면균열의 성장거동을 조사 연구하였다. 또한 주파수의 영향을 조사 하기 위하여 538.deg. C에서 고온피로시험을 실시하여 이 결과를 크리이프 및 크리이프피로 시험의 결과와 비교.검토하였다.

• 대한기계학회논문집
• /
• 제12권6호
• /
• pp.1320-1326
• /
• 1988

본 연구에서는 파괴역학적인 해석법과 표면레프리카법을 확장, 적용시켜 피로 -크리프하의 유지시간에 따른 작은 표면균열의 분포상태와 이의 합체, 성장 및 밀도변 화특성을 해석하여 기초적 자료를 얻는다.

• Composites Research
• /
• 제21권6호
• /
• pp.15-22
• /
• 2008

본 연구는 SiC입자를 20% 강화된 알루미늄기 복합재료를 이용해서 평면굽힘피로시험을 향했다. 표면미소피로균열의 발생 및 진전거동은 레프리카법으로 연속관찰을 했고 파괴원인과 파괴기구를 규명하기 위해서 주사전자현미경을 이용했다. da/dn-$K_{max}$ 관계에서 저응력 레벨에서는 여러 개의 균열이 진전하고, 합체 등이 일어나는 것으로부터 진전속도는 꽤 분산(흐트러짐)이 심하고, 고응력 레벨에서는 비교적 흐트러짐은 적게 나타나는 것을 알 수 있었다.

• 대한조선학회지
• /
• 제21권1호
• /
• pp.35-42
• /
• 1984

In the present study, rotating bending fatigue tests have been carried out in three kinds of carbon steel specimens; an annealed low carbon steel, an annealed high carbon steel and quenched-tempered high carbon steel; with a small artificial surface defect that might exist in real structures. Fatigue crack lengths have been observed by a method of replication in order to investigate the growth characteristic of fatigue crack in the viewpoints of strength of materials and fracture mechanics. The main results obtained are as follows: 1) The effect of a small surface defect upon the reduction of fatigue limit is considerably large, and the rate of fatigue limit reduction grows in the following order; annealed low carbon steel(mild steel), annealed high carbon steel, quenched-tempered high carbon steel. 2) When the growth rate of surface crack length(2a) was investigated in the viewpoints of fracture mechanics based upon $ ${\Delta}K_{\varepsilon}$, the dependence of stress level and of surface defect size disappear, and there exists a linear relationships between d(2a)/dN and ${\Delta}K_{{\varepsilon}t},\;\Delta_{{\varepsilon}t}\sqrt{{\pi}a}$, on log. plot, i.e, $d(2a)/dN={C{\cdot}{\Delta}K_{\varepsilon}}^3_t$, where ${\Delta}_{{\varepsilon}t}\sqrt{{\pi}a}$ a is the cyclic total strain intensity factor range.

• Tribology and Lubricants
• /
• 제24권6호
• /
• pp.332-337
• /
• 2008

This paper presents the surface defect analysis based on the experimental investigation of scribed glasses. The scribing process by a diamond wheel cutter is widely used as a reliable and inexpensive method for sizing of glass sheets. The wheel cutter generates a small median crack on the glass surface, which is then propagated through the glass thickness for complete separation. The surface contour patterns in which are formed during a scribing process are strongly related to wheel cutter parameters such as wheel tip surface finish, tip angle and wheel diameter, and cutting process parameters such as scribing pressure, speed and tooling technique. The scribed surface of a glass sheet provides normal Wallner lines, which represent regular median cracks and crack propagation in glass thickness, and abnormal surface roughness patterns. In this experimental study, normal and abnormal surface topographic patterns are classified based on the surface defect profiles of scribed glass sheets. A normal surface of a scribed glass sheet shows regular Wallner lines with deep median cracks. But some specimens of scribed glass sheets show that abnormal surface profiles of glass sheets in two pieces are represented by a chipping, irregular surface cracks in depth, edge cracks, and combined crack defects. These surface crack patterns are strongly related to easy breakage of the scribed glass imposed by external forces. Thus the scribed glass with abnormal crack patterns should be removed during a quality control process based on the surface defect classification method as demonstrated in this study.

• 한국해양공학회지
• /
• 제4권2호
• /
• pp.250-250
• /
• 1990

In this paper, fatigue tests were carried out at stress test levels of 461 MPa, 441 MPa, and 431 MPa by using smooth specimen of$2_{1/4}$ Cr-1 Mo steel with the stress ratio(R) of 0.05. The initiation, growth and coalescense process of the major cracks and sub-cracks among the fatigue cracks on the smooth specimen are investigated and measured under each stress level at a constant cycle ratio by the replica technique with optical microscope. Some of the important results are as follows: In spite of the difference of stress levels, the major crack data gather into a small band in the curve of surface crack length and crack depth against cycle ratio N/Nf. The sub-crack data, however, deviate from the band of the major crack. The growth rates, da/dN, of major and sub-crack plotted against the stress intensity factor range, ${\Delta}K$, have the tendency to be compressed on a relatively small band. But it is more effective to predict fatigue life through major cracks. The propagation behavior of surface microcracks on the smooth specimens coincides with that of the specimen having an artificial small surface defect or through crack.

• International Journal of Precision Engineering and Manufacturing
• /
• 제5권4호
• /
• pp.36-42
• /
• 2004

The shaft with the circular cross section has symmetric structural combination parts to keep the rotating balance. Hence the crack usually initiates from symmetric combination parts due to the stress concentration of these parts. In this study to estimate the fatigue behavior of symmetric cracks, the fatigue test was performed by using a rotary bending tester and the specimen with symmetric defects in circular cross section. The characteristics of crack initiation and propagation on the symmetric surface cracks in circular cross section were examined. We also observed the internal crack using the oxidation coloring method and investigated the fatigue behavior using the relationship between the surface crack and the internal crack. As a result, the fatigue life of symmetric cracks was reduced by 35% compared to that of a single crack. We examined the characteristics of fatigue behavior of elements with symmetric cracks using internal crack propagation rate and maximum stress intensity factor range that were obtained from an approximation method.

• 대한기계학회논문집
• /
• 제14권3호
• /
• pp.603-609
• /
• 1990

본 연구에서는 미소균열의 정의로서 균열의 크기가 재료의 조직의 크기와 order적으로 같은 균열의 특성이라는 것과 균열의 크기가 소성역 크기와 order적으로 같은 균열의 특성에 착안해서 탄소강 평활재와 예균열재(pre-cracked specimen)에 대 해서 응력비 R=-1 및 R=0의 피로한도 특성과 평활재의 미소균열의 검출 및 정류균열의 생성기구를 균열 열림 닫힘에 주목해서 검토하였다.

• 대한기계학회논문집
• /
• 제8권3호
• /
• pp.195-200
• /
• 1984

본 연구에서는 SUS 304강의 상온하의 평골재 표면에 발생. 성장하는 미소표면 피로균열의 거동을 파괴역학적 관점과 수법으로 정량적으로 조사하려는 연구의 일환 이다.