• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2011.11a
• /
• pp.645-648
• /
• 2011

Hydrazine which has been used as monopropellant shows high performance, but because of its high toxicity research for new green propellant that could replace hydrazine is going on. Ionic liquid propellant that is one of the green propellant has lower toxicity, higher specific impulse, and higher density than hydrazine. To design the thruster which use Hydroxylamine Nitrate (HAN), one of ionic liquid propellant, as a propellant, a quantity of catalyst for full decomposition of a propellant is needed. In this study, reference point for HAN thruster design could be suggested through a design of a small scale thruster which used HAN propellant, and propellant decomposition capability evaluation with characteristic velocity efficiency.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2011.11a
• /
• pp.336-339
• /
• 2011

Hot-fire test facility is one of the most important infrastructure for thruster development and evaluation. During the past three years, Korea Aerospace Research Institute (KARI) and Hanwha Corporation have successfully performed the construction of hot-fire test facility for medium-scale monopellant thruster to the maximum 200N thrust level. In general, thruster hot-firing test should be performed in vacuum conditions to simulate space environment. The hot-fire test facility is divided into three subsystems, vacuum system, propellant supply system and data measurement & control system. The goal of this facility is to extend the capability from small thruster for satellite mission to medium-scale thruster for launch vehicle and lunar mission. In this paper, the progress and overview for thruster hot-fire test facility was introduced and test results were also presented.

• Proceedings of the KSME Conference
• /
• 2004.04a
• /
• pp.1280-1285
• /
• 2004

Microsystem technology has been applied to space technology and became one of the enabling technology by which low cost and high efficiency are achievable. Micro propulsion system is a key technology in the miniature satellite because micro satellite requires very small and precise thrust force for maneuvering and attitude control. In this paper research on micro solid propellant thruster is reported. Micro solid propellant thruster has four basic components; micro combustion chamber, micro nozzle, solid propellant and micro igniter. In this research igniter, solid propellant and combustion chamber are focused. Micro igniter was fabricated through typical micromachining and evaluated. The characteristic of solid propellant was investigated to observe burning characteristic and to obtain burning velocity. Change of thrust force and the amount of energy loss following scale down at micro combustion chamber were estimated by numerical simulation based on empirical data and through the calculation normalized specific impulses were compared to figure out the efficiency of combustion chamber.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2008.05a
• /
• pp.145-148
• /
• 2008

A 50 Newton monopropellant thruster being developed for attitude control in a variety of aerospace application systems is described in this paper. A scaled down thruster with platinum on aluminum oxide in the reaction chamber was tested to determine the catalyst capacity. A scaled up thruster, was designed and fabricated using data obtained on small scale device, was evaluated by decomposition efficiency based on temperature, efficiency of characteristic velocity, and measurement of thrust. The performance of a scaled up thruster was 42 Newton in thrust, 98 % in efficiency of characteristic velocity, and 123 sec in specific impulse at sea level.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.12 no.3
• /
• pp.24-33
• /
• 2008

A 50 Newton monopropellant thruster being developed for attitude control in a variety of aerospace application systems is described in this paper. A scaled down thruster with platinum on aluminum oxide in the reaction chamber was tested to determine the catalyst capacity. A scaled up thruster which was designed and fabricated using data obtained from a small scale device was evaluated by its decomposition efficiency based on the temperature, the efficiency of characteristic velocity, and the measurement of thrust. The performance of a scaled up thruster was marked by a measured thrust of 42 Newton, 98 % efficiency of the characteristic velocity, a specific impulse of 123 sec at sea level.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.22 no.3
• /
• pp.81-89
• /
• 2018

In this study, the operating characteristics of a small-scale pulse detonation engine (PDE) were investigated experimentally for application as a small thruster and an igniter. The PDE was constructed using commercial gas tubes with an inner diameter of 4.22 mm. The operating and detonation propagation characteristics of the PDE were investigated over the ranges of equivalence ratios and operating frequencies. Measured detonation speed was close to 10% of the theoretical CJ values at 1 Hz and 5 Hz conditions. However, unstable propagation characteristics were shown at 20 Hz and lean conditions, where the velocity deficit was increased by 20~62%.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.16 no.2
• /
• pp.1-9
• /
• 2012

Applicability of regenerative cooling in 2,500 N-class bipropellant thruster using hydrogen peroxide and kerosene was considered for improvement of performance and application in various missions. Calculation was performed by one dimensional approach using hydrogen peroxide as a coolant. The heat flux of thruster at nozzle throat was estimated at 18 - 20 MW/$m^2$. Designed cooling channel width and height were 2.5 mm and 0.5 mm, respectively. Based on designed cooling channel configuration, flat plate model was manufactured and tested for estimation of pressure drop in cooling channel, and CFD analysis was compared with the test result. The maximum error between CFD analysis and experimental result was approximately 13% and average error was approximately 5%.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2011.11a
• /
• pp.163-170
• /
• 2011

Applicability of regenerative cooling in 2,500 N-class bipropellant thruster using hydrogen peroxide and kerosene was considered for improvement performance and application in various missions. Calculation was performed by one dimensional approach using hydrogen peroxide as a coolant. In designed regenerative cooling thruster, heat flux at nozzle throat was estimated at 18 ~ 20 $MW/m^2$. Designed cooling channel width and height were 2.5 mm and 0.5 mm, respectively. Based on designed cooling channel configuration, flat plate model was manufactured and tested for estimation of pressure drop in cooling channel, and CFD analysis was compared with the test result. The maximum error between CFD analysis and experimental result was approximately 13% and average error was approximately 5%.

• International Journal of Aeronautical and Space Sciences
• /
• v.18 no.3
• /
• pp.512-521
• /
• 2017

This paper reports development process of a university-based sounding rocket using simplified hybrid rocket propulsion system for low-altitude flight application. A hybrid propulsion system was tried to be designed with as few components as possible for more economical, simpler and safer propulsion system, which is essential for the small scale sounding rocket operation as a CanSat carrier. Using blow-down feeding system and catalytic ignition as combustion starter, 250 N class hybrid rocket system was composed of three components: a composite tank, valves, and a thruster. With a composite tank filled with both hydrogen peroxide($H_2O_2$) as an oxidizer and nitrogen gas($N_2$) as a pressurant, the feeding pressure was operated in blowdown mode during thruster operation. The $MnO_2/Al_2O_3$ catalyst was fabricated for propellant decomposition, and ground test of propulsion system showed the almost theoretical temperature of decomposed $H_2O_2$ at the catalyst reactor, indicating sufficient catalyst efficiency for propellant decomposition. Auto-ignition of the high density polyethylene(HDPE) fuel grain successfully occurred by the decomposed $H_2O_2$ product without additional installation of any ignition devices. Performance test result was well matched with numerical internal ballistics conducted prior to the experimental propulsion system ground test. A sounding rocket using the developed hybrid rocket was designed, fabricated, flight simulated and launch tested. Six degree-of-freedom trajectory estimation code was developed and the comparison result between expected and experimental trajectory validated the accuracy of the developed trajectory estimation code. The fabricated sounding rocket was successfully launched showing the effectiveness of the simplified hybrid rocket propulsion system.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.48 no.2
• /
• pp.1-8
• /
• 2011

An underwater robot S/W framework consists of various sub-modules such as sensory data processing module, thruster control module, cognition module and behavior control module. Performance of a robot is determined by not only the efficiency of algorithms used but also effectiveness of their implementations. One most important factor of the effective implementation is the efficiency of data sharing module, as it transmits signals and data between the sub-modules and thus is directly related to the cycles of sensing and control The ideal data sharing module enables immediate access to any data source irrespective of system configurations. In reality, however, there are lots of obstacles including limitation of processing capacity of source modules, delay over network, and scheduling latency of operating systems. The paper proposes a new data sharing architecture and programming models to effectively handle such obstacles in implementation of underwater S/W framework on a small scale distributed computing system.