• Journal of environmental and Sanitary engineering
• /
• v.14 no.2
• /
• pp.84-89
• /
• 1999

This experiment was performed to develop the new desulfurization process which can eliminate the possibility of generation of the secondary pollutants by regenerating the limestone from the sulfite/sulfate slurry generated from the wet lime/limestone flue gas desulfurization process by treating it with the ammonium hydroxide and carbon dioxide and using it again. In the experiments, regent grade calcium carbonate was dissolved to obtain the 200ml of sample slurry of the concentration of 2.0~0.4 weight percent. After three times of regeneration and desulfurization process, the coefficients of regeneration and desulfurization efficiencies are calculated/measured. The obtained results are that the coefficients of generation of the first. second, and third regenerated calcium carbonate were 90.88, 92.13, and 91.50%, respectively; and the desulfurization efficiencies of those are 93.4, 94.2 and 93.0%, respectively.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2004.03b
• /
• pp.672-677
• /
• 2004

This paper is on determination method of preconsolidation pressure and consolidation coefficient using Kores University Calibration Chamber System(KUCCS). High-quality, large-size cohesive soil specimen was prepared by using two-stage slurry consolidation technique, which has many advantage for research and calibration purpose. The result from consolidation stage in KUCCS was compared with results of oedometer test. The results by Casagrcnde method gave very good agreement with preconsolidation pressure in slurry consolidometer. And, the predicted consolidation coefficient by log t method showed agreement with the experimental results in KUCCS.

• Journal of the Korean Ceramic Society
• /
• v.44 no.10
• /
• pp.548-553
• /
• 2007

Ceramic green sheets consisting Bi-based glass frit were fabricated for an application to PDP transparent dielectric front panel. The dispersion condition of the slurry for tape casting was pre-examined, and two kinds of hinder and plasticizer were used in the non-aqueous slurry system. In the fabrication process for the frit film, the properties such as dry and firing shrinkage, elongation, and transmittance were examined at the condition of various mixing ratio of plasticizers. In the mixing ratio of polyethylene glycol to dibutyl phthalate of 3:5wt%, a good adhesion, elongation and transmittance were observed at the firing temperature of $580^{\circ}C$. The photograph for the cross section of the interface was also showed a dense microstructure.

• Journal of Environmental Science International
• /
• v.7 no.5
• /
• pp.659-667
• /
• 1998

In the present paper, batch and semi-continuous settling characteristics of a binary calcium carbonate-water system were investigated. Using experimental data of batch settling characteristics, a graphical analysis for a semi-continuous thickening column was developed and compared with experimental results on the basis of Kynch theory, only where the feed velocity line was within the limits of Kynch theorem III. The analysis showed good agreement with experiments. Quite erroneous results, however, was observed for the analysis of a sludge region on the underloaded operation, which was considered due to the deviation from the limits of theory.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2003.11a
• /
• pp.938-943
• /
• 2003

The characteristics of lightweight cellular concrete has much influence on the compressive strength and flow from the design of mixture. This study is to investigate the characteristics of the compressive strength and flow for the mixture of lightweight cellular slurry. KS F 4039 was compared to the construction system and quality for lightweight cellular comcrete of floating floor. As the result of this study, the standard of the compression strength for target slurry have to lower and an upper limit of flow was judged to be 230mm

• Transactions of Materials Processing
• /
• v.24 no.2
• /
• pp.83-88
• /
• 2015

For chromaticity correction, it is necessary to dispense high viscosity phosphor slurry since it greatly affects the performance of white LEDs. However, it is quite difficult to dispense high viscosity fluorescent materials. In the current study, micro-discharge electrostatic printing has been used for dispensing various high viscosity phosphor slurries. We have achieved dispersions of up to 50 µg using drop on demand (DOD) discharge experiments. The experiments were conducted with different combinations of process variables such as applied voltage, pneumatic pressure, and frequency.

• Journal of Korea Foundry Society
• /
• v.20 no.4
• /
• pp.277-282
• /
• 2000

The RP&M (Rapid prototyping and Manufacturing) is the most appropriate technology for the small-lot production system, in which the production cycle is getting shorter owing to various needs from consumers. In this paper, RP&M is applied to a casting process. A casting process has a merit of being able to reflect complicated shapes at one time. But it has not been applied to the precision industry because of bad quality on surface. So we will improve characteristics of aluminum casting process using vacuum sealed casting process and porous ceramic mold which is made by slurry casting process.

• Journal of the Korean Society for Precision Engineering
• /
• v.16 no.11
• /
• pp.62-67
• /
• 1999

The RP&M(Rapid Prototyping and Manufacturing) is the most appropriate technology for the small-lot production system, in which the production cycle is getting shorter owing to various needs from consumers. Recently RP products which are made of plastics, wax, and paper are used to verify the design of samples. But these products cannot be applied to the real mold because the strength enough to be a mold cannot be given by soft materials such as plastics. So RP products are copied to AFR(Al powder Filled Resin) molds or metal molds, which is called the RP&M. In this paper, RP&M is applied to a casting process. A porous casting mold, which is made from ceramic powder and binder, is used for rapid tooling of aluminum shoes molds.

• Proceedings of the SAREK Conference
• /
• 2004.11a
• /
• pp.8-8
• /
• 2004

• Proceedings of the Membrane Society of Korea Conference
• /
• 1998.06a
• /
• pp.25-48
• /
• 1998

Current topics related to membrane technology under the recent water environment are as follows: - Cryptosporidum Outbreak - Integrity Control System - Water re-use - Recycle Society - Biotreatment and Membrane - Slurry or Sludge Treatment I would like to introduce the actual examples regarding water re-use. mainly on the above 5 topics.