• Journal of Advanced Marine Engineering and Technology
• /
• 제28권3호
• /
• pp.551-558
• /
• 2004

Recently, fuel prices have been continually raised in diesel engine. Such a change in the fuel price influences enormously the development trend of marine diesel engines for slow speed, In other words, the focus was shifted from large diameter and high speed to low fuel consumption. Accordingly, more efforts are being made for engine manufacturing and development to develop highly efficient engines. In this study. a single cylinder 4 stroke cycle DI slow speed diesel engine was designed and manufactured, a 4 stroke cycle was configured and basic performances were evaluated. The results are as follows. The optimal fuel injection timing had the lowest value when specific fuel consumption was in BTDC 8~$10^{\circ}$, a little more delayed compared to high speed diesel engines. Cycle variation of engines showed about 5% difference at full loads. This is a significantly small value compared to the cycle variation in which stable operation is possible, showing the high stability of engine operation is good. The torque and brake thermal efficiency of engine increased with an increase of engine 250-450 rpm. but fuel consumption ratio increased from the 450 rpm zone and thermal efficiency abruptly decreased. Mechanical efficiency was maximally 70% at a 400 rpm that was lower than normal engines according to the increase of mechanical frictional loss for cross head part. The purpose of this study was to get more practical engines by comparing the above results with those of slow speed 2 stroke cycle diesel engines.

• Journal of Advanced Marine Engineering and Technology
• /
• 제17권5호
• /
• pp.33-43
• /
• 1993

Recent marine propulsion diesel engines tend to become slower in speed and longer in stroke for the higher engine efficiency, and in these long stroke and slow speed engines the digital governors are highly recommended to be used. But, in the present digital governors only the feedback of the engine rpm-signal is used for the engine speed control and it does not work so effectively when the load variation is large. In this paper, a new method is proposed to improve the speed control performance in a diesel engine, by adding the torque feedback loop to the present digital governor which uses the rpm feedback PID controller only. And also a method is proposed to adjust the parameters of the PID controller optimally.

• Journal of Advanced Marine Engineering and Technology
• /
• 제17권2호
• /
• pp.29-35
• /
• 1993

Recent marine propulsion diesel engines tend to become slower in speed and longer in stroke for the higher engine efficiency, and in these long stroke and slow speed engines the digital governors are highly recommended to be used. But, in the present digital governors only the feedback of the engine rpm-signal is used for the engine speed control. If the load torque of the engine can be measured or estimated and the torque feedback loop is added to the present digital governor, it is expected that the speed control performance of the digital governor will be highly improved. In this paper, a new method is proposed to estimate the load torque of the diesel engine from the measured signals of fuel oil and rpm. And it is also suggested that the Kalman filter can be used for the estimation of engine torque.

• Journal of Advanced Marine Engineering and Technology
• /
• 제19권3호
• /
• pp.24-32
• /
• 1995

The scavenging characteristics have a great influence on the performance of a diesel engine, especially slow-speed two-stroke diesel engines which are usually used as a marine propulsion power plant, and they are greatly affected by the conditions in the cylinder, intake and exhaust manifolds, and the opening and closing timing of scavenging ports or exhaust valves during the gas exchange process. Besides, there are many other factors to affect the scavenging characteristics and these factors interact each other very complicatedly. Therefore the simulation program of the gas exchange process is very useful to improve and predict the scavenging characteristics, due to the high costs associated with redesign and testing. In this paper it was attenpted to investigate the effect of the variation of the pressure ratio of intake to exhaust manifolds, and the variation of the opening and closing timing of a exhaust valve by using a computational program for a three-zone scavenging model which was developed by authors. The computed results showed that the scavenging efficiency and delivery ratio increased considerably, but the trapping efficiency decreased with increasing of the pressure ratio of intake to exhaust manifolds. The scavenging efficiency, trapping efficiency, and th conditions of the cylinder gases were affected by the opening timing of the exhaust valve, but the delivery ratio by the closing timing.

• 한국수소및신에너지학회논문집
• /
• 제24권5호
• /
• pp.461-466
• /
• 2013

In this research, the diesel cycle was thermodynamically interpreted to evaluate the possibility of high efficiency by converting diesel engine to the atkinson cycle, and general cycle features were analyzed after comparing these two cycles. That an experimental single cylinder and a long stroke diesel-atkinson engine, of which S/B ratio was more than 3, were manufactured. After evaluating the engine through basic experiments, a diesel engine was converted into the atkinson cycle by constituent VCR (variable compression ratio) device and VVT (variable valve timing) system. The experimental method was to observe compression work reduction effects due to low compression effects from delayed intake valve closing of the early stage atkinson engine. The result, the possibility of increasing compression ratio about each engine load was confirmation by constructing compensate expansion-compression ratio in accordance with the delayed intake valve close.

• Journal of Advanced Marine Engineering and Technology
• /
• 제12권1호
• /
• pp.28-36
• /
• 1988

Since the oil shocks of 1970s, the quality of the fuel oil for marine diesel engines has become more degarded than ever. When the poorer quality fuel is burned, carbon residues of the fuel oil cause blockage of the fuel injection valve nozzle and troubles of fuel injection system. The mis-firing of engine occurs due to the decrease of fuel quantity injected, the decrease of compression pressure in the slow speed range, the increase of fuel leaked and the high ignition temperature of degraded fuel etc. This paper is to investigate theoretically the effects of mis-firing on the crankshaft axial vibration of diesel engine. The cylinder pressure in operation is calculated by the computer aided simulation of closed cycle for a large two-stroke diesel engine and also the exciting force of axial vibration and the resonance amplitudes are calculated. And then, the condition of normal state, misfiring and one-cylinder cut-off operation are analyzed. The results of calculations show good agreements with those of the actual measurements.

• 한국분무공학회지
• /
• 제22권4호
• /
• pp.203-209
• /
• 2017

The International maritime organization(IMO), in an effort to slow down the global warming, proposes reduction in ship's speed as a way to lower the rate emissions from ships. In addition, since ship's fuel cost have been increased, the shipping volumes, fuel-saving technology are being required urgently. Therefore, in this present study, a method of reducing the fuel cost that can improve the performance of the diesel engine was tried by introducing a predetermined amount (0.1~0.3% of the mass amount of fuel used) of hydrogen fuel additive. The experimental conditions of the test engine were 1500rpm and torque BMEP-10b ar. The engine performances (power output, fuel consumption rate, p-max, exhaust temperature) were compared before and after addition of hydrogen fuel additives. This experimental study confirmed reducing at least 2% fuel consumption and 2.19% NOx emission.

• Journal of Advanced Marine Engineering and Technology
• /
• 제19권4호
• /
• pp.61-71
• /
• 1995

Nowadays the thin-walled metal bearing, which is made seperately from the bearing housing and has the ratio of wall thickness/bearing diameter being less than 1/30, are used in many newly developed large-sized slow speed diesel engines for the purpose of upgarding lubication performance and easy maintenance according to the trends of increasing output per cylinder and lowering engine speed. The type of this bearing has been used generally in many small-sized high speed engines applied for automobile, high speed craft and industrial power generation systems since 1950s. But the tranditional thick-walled bearings, whice are linned white metal on the bearing housing directly, have been installed on the large and slow speed engines until 1990s due to the easy manufacturing procedures. In this study we have calculated optimum dimensions of the metal bearing, fabricated special zigs for crush measurement, model test machine, 2 sets of specimens.(crosshead pin bearing, $\phi$818*552*20mm) for B & W 6S70MC(20, 940*88rpm), and evaluated metal constact phenomena of white metal, its friction coefficient, temparature rise through the model test and field performance test.

• 한국자동차공학회논문집
• /
• 제12권5호
• /
• pp.40-57
• /
• 2004

The effects of triple (pilot, main and after) injection on combustion and emission characteristics in a HSDI (High-Speed Direct Injection) diesel engine were investigated using a single-cylinder optical diesel engine equipped with a common-rail injection system. The pilot injection affected the spray and combustion evolution of the following main injection. It was found that the pilot injection reduced the ignition delay, which led to lowered NOx (Nitric Oxides) level, and increased IMEP (Indicated Mean Effective Pressure) due to slow combustion pace during an expansion stroke. The after-injection was shown to be effective in reducing PM (Particulate Matter) even when a small amount of fuel was added. The results suggest that a proper combination of individual injection strategy could bring about a good synergetic effect on engine performance and emission.

• 한국마린엔지니어링학회:학술대회논문집
• /
• 한국마린엔지니어링학회 2012년도 전기공동학술대회 논문집
• /
• pp.223-223
• /
• 2012