• Earthquakes and Structures
• /
• 제3권2호
• /
• pp.169-180
• /
• 2012

The performance of pure friction isolation system with respect to the frequency bandwidth of excitation and the predominant frequency is investigated. A set of earthquake ground motions (artificial as well as recorded [with different combinations of magnitude-distance and local site geology]) is considered for investigating effectiveness of pure friction isolators. The results indicate the performance of pure friction base isolated system does not only depend upon coefficient of friction and mass ratio but the stick-slip behaviour depends upon the frequency content of the excitation as well. Slippage prevails if the excitation frequency lies in a suitable frequency range. This range widens with increasing mass ratio. For larger mass ratios, the sliding effect is more pronounced and the maximum acceleration response is further reduced in the neighbourhood of frequency ratio (${\omega}/{\omega}_n$) of unity. The pure friction isolation system is effective in the case of broadband excitations only and that too, in the acceleration sensitive range of periods. The pure friction system is not effective for protection against narrow band motions for which the system response is quasi-periodic.

• 전기학회논문지
• /
• 제58권3호
• /
• pp.531-538
• /
• 2009

The paper deals with an operation scheme to improve the forecasting of output range and to regulate the active power output of the hybrid system consisting of a doubly fed induction generator (DFIG) and a fuel-cell. The power output of the wind turbine fluctuates as the wind speed varies and the slip power between the rotor circuit and power converter varies as the rotor speed change. The power fluctuation of a DFIG makes its operation difficult when a DFIG is connected to grid. A fuel cell system can be individually operated and adjusted output power, hence the wind turbine and fuel cell hybrid system can overcome power fluctuation by using a fuel-cell power control. In this paper, a fuel-cell is performed to regulate the active power output in comparison with the regulated active power output of a DFIG. And it also improves the forecasting of output range. Based on PSCAD/EMTDC tools, a DFIG and a proton exchange membrane fuel cell(PEMFC) is simulated and the dynamics of the output power in hybrid system are investigated.

• 한국기계가공학회지
• /
• 제17권4호
• /
• pp.70-75
• /
• 2018

This paper describes an Integrate Dynamic Control system with Brake System (IDCB) for SUV vehicles. The system was developed to stabilize the lateral dynamics, maintain the steerability and improve the ride comfort on various roads. A fuzzy logic control method is used to design the IDCB. The performance of the IDCB is validated under different road and driving conditions. The results show that the IDCB tracks the reference yaw rate under all tested conditions; in addition, it reduces the body slip angle and roll angle. When a vehicle runs on a split-${\mu}$ road and a brake input is applied, the IDCB virtually eliminates the lateral dynamics. Thus, the IDCB improves the lateral stability, preserves the steerability and enhances the ride comfort of vehicles.

• 한국자동차공학회논문집
• /
• 제20권5호
• /
• pp.130-137
• /
• 2012

Automotive engines need strategies to satisfy with the emission regulations in terms of PM and NOx. HC-LNT (Hydrocarbon-Lean NOx Trap) with secondary injection system is considered as more practical technology in order to cope with emission regulations. The HC-LNT system, which is using diesel fuel itself as a reducing agent, absorbs NOx in lean exhaust gas condition and releases NOx in rich exhaust gas conditions. In this system, inappropriate amounts of reducing agent will slip through the LNT without the profits of conversion and cause additional emission problems. Therefore, the suitable amount of reducing agent should be supplied into the catalytic converter. In this research, engine emission test was conducted to optimize injection quantity at the various engine test conditions. Different exhaust layouts and catalyst shapes have been studied and extension unit which makes better uniformity of exhaust gas was used for HC-LNT system. From this results, the effect of secondary injection conditions on NOx conversion characteristics of HC-LNT was clarified.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2003년도 학술회의 논문집 정보 및 제어부문 B
• /
• pp.612-615
• /
• 2003

In this paper, a design of radiation detector for gamma column scanner is introduced. Distillation column is important unit in Petro-chemical industries, and its on-line diagnose is very important. To get density profile measured by the radiation transmitted through column is well method for on-line diagnose as gamma scanning. For this purpose radiation detection circuit, radiation source and mechanical system for moving source and detector are required. Conventional radiation detection circuit for this application is sensitive to electric noise because of interface between the radiation circuit and the controller for mechanical system. The radiation detection system introduced here is using loop coil instead of slip ring to remove contact noise. Radiation detection system designed here for gamma scanning consist of BGO detector, high voltage circuit, PHA circuit and FSK modem. The BGO detector is used as radiation sensor, high voltage circuit and peak height analysis circuit is essential to process the signal generated from BGO detector. Micro controller convert measured data into ASCII data. FSK modem transmit ASCII data. Transmitted ASCH data is picked up in antenna coil and processed for combined function with mechanical system. This method gives good result by isolating the controlling circuit of mechanical system from radiation detecting circuit which is sensitive to noise.

• Journal of Advanced Marine Engineering and Technology
• /
• 제29권3호
• /
• pp.306-312
• /
• 2005

IMO $NO_x$ levels are generally possible to meet by means of primary on-engine measures. Further significant follow-on reductions are likely to require a secondary after-treatment technique. SCR(Selective Catalytic Reduction) technology is used almost exclusively for $NO_x$ removal in stationary combustion systems. In order to develop a practical SCR system for marine application on board ship, a primary SCR system using urea was made. The SCR system was set up on the ship, 'HANNARA' as a test vessel. employed a two-stroke cycle diesel engine as main propulsion, which is a training ship of Korea Maritime University. The purpose of this paper is to report the results about the basic effects of the below system parameters, The degree of $NO_x$ removal depends on some parameters, such as the amount of urea solution added, space velocity, reaction gas temperature and activity of catalyst.

• Computers and Concrete
• /
• 제6권3호
• /
• pp.187-202
• /
• 2009

This paper focuses on the flexural behavior of RC beams externally strengthened with Carbon Fiber Reinforced Polymers (CFRP) fabric. A non-linear finite element (FE) analysis strategy is proposed to support the beam flexural behavior experimental analysis. A development system (QUEBRA2D/FEMOOP programs) has been used to accomplish the numerical simulation. Appropriate constitutive models for concrete, rebars, CFRP and bond-slip interfaces have been implemented and adjusted to represent the composite system behavior. Interface and truss finite elements have been implemented (discrete and embedded approaches) for the numerical representation of rebars, interfaces and composites.

• 한국자동차공학회논문집
• /
• 제19권1호
• /
• pp.51-57
• /
• 2011

Information of the lateral velocity and the sideslip angle in a vehicle is very useful in many active vehicle safety applications such as yaw stability control and rollover prevention. Because cost-effective sensors to measure the lateral velocity and the sideslip angle are not available, reliable algorithms to estimation them are necessary. In this paper, a sliding mode observer is designed to estimate the lateral velocity. The side slip angle is estimated using the recursive least square with the disturbance observer and the pseudo integral. The estimated parameters from the combined estimation method are updated recursively to minimize the discrepancy between the model and the physical plant, and any possible effects caused by disturbances. The performance of the proposed monitoring system is evaluated through simulations and experiments.

• 동력기계공학회지
• /
• 제9권2호
• /
• pp.45-49
• /
• 2005

Liquefied natural gas takes up six hundredths of the volume of natural gas, which makes storage and transportation much easier. To send out natural gas via a pipeline network across the nation, high-pressure LNG pumps supply highly compressed LNG to high-pressure vaporization facilities. The Number of high-pressure LNG pumps determined the send-out amount in LNG receiving terminal. So it is main equipment at LNG production process and should be maintained on best conditions. In this paper, to find out the cause of high beat vibration at cryogenic pumps, vibration and motor current signal analysis have been performed. High vibration of cryogenic pumps could be reduced due to the modification of motor rotor.

• 한국자동차공학회논문집
• /
• 제4권6호
• /
• pp.109-120
• /
• 1996

Serpentine belt drive system offers the advantages of light weigh, low cost, quientness, and efficiency. Since these belts are typically longer than conventional belts, a tensioner component is added to maintain acceptable belt tension levels and make no slippage between pulleys and belts. This paper addresses the modeling and analysis of the automotive belt drive systems and also addresses the predicton of slippage on rotational modes. Vibration characteristics are determined from the eigenvalue problem governing the free response. Under certain engine operating conditions, the dynamic tension fluctuations may be sufficient to cause the belt to slip on particular accessory pulleys, It is found that this slippage can be reduced by adding the tensioner component from the analysis of belt tension and belt compression.