• Tribology and Lubricants
• /
• 제21권1호
• /
• pp.16-20
• /
• 2005

Friction and wear characteristics between two steel surfaces under fretting condition are investigated experimentally. The fretting damage caused by low-amplitude oscillatory sliding can be classified into three regimes of gross-slip, mixed-slip and partial-slip due to stick-slip phenomenon. One of the most important characteristics of fretting wear is the transition from gross-slip to mixed-slip. This study was focused on getting the degree of stick-slip out of the friction transition under fretting condition. Fretting wear is divided into three conditions of gross-slip/mixed-slip/partial-slip. The criteria for the division are friction and displacement amplitude, wear scar morphology and dissipated energy. In this test, friction force and displacement were measured for detecting the transition from mixed-slip to gross-slip and qualitatively predicting the degree of the wear.

• 한국결정성장학회지
• /
• 제15권5호
• /
• pp.202-207
• /
• 2005

Kaolin과 규석 및 $Mg(OH)_2$등의 원료로 만들어진 slip을 casting 할 때 slip의 점도가 slip casting 속도와 소결체의 미세조직에 미치는 영향을 보면 slip-casting속도는 slip의 점도가 낮을 경우 감소하였으며 slip의 점도범위는 $3.0\~17.0\;cP$가 적당하였다. Slip의 점도를 조절하면 표면층, 표면 내부층, 중간층, 내면층의 미세조직을 비교적 균일하게 casting 할 수 있다 소성온도 $1350^{\circ}C$에서 시편의 구성광물은 cordierite 결정만으로 되어있었다.

• 대한전자공학회논문지TC
• /
• 제44권3호
• /
• pp.41-50
• /
• 2007

본 논문에서는 IP 스위칭 시스템을 위한 iSLIP 기반의 Dual Round Robin(DRR) 방식 스케줄링 알고리즘을 제시한다. 기존의 iSLIP 방식과 DRR 방식을 결합하여 단점은 최소화하면서 DRR이 가진 분배기능의 장점과 iSLIP 기능이 가진 고성능의 장점을 이용할 수 있게 한다. 불균일한 트래픽 환경에서 스위치에서의 처리율과 지연성능을 컴퓨터 시뮬레이션을 통해 확인한다. 또한 제안된 방식은 기존의 iSLIP과 비교하여 구현 복잡성을 매우 낮아짐을 보인다. 이러한 실험을 통해 본 논문에서 제안한 스케줄링 알고리즘이 기존의 DRR에 비해 우수한 성능을 iSLIP에 비해 구현의 복잡성에서 우수함을 알 수 있었다.

• 대한인간공학회지
• /
• 제20권2호
• /
• pp.47-57
• /
• 2001

To simulate an actual slip to measure floor slipperiness, slip resistance testers simulate slip in only forward direction because forward slip in the landing phase was found to be the most important factor for loss of balance. Backward slip in the take off phase was possible but was excluded in the friction test protocol because it was not dangerous. However, backward slip was tested in the friction test protocol without any theoretical background of the significance in generating dangerous slips and falls and was proven to be as good as forward slip in measuring floor slipperiness. Therefore, this study was designed to investigate the significance of backward slip in generating dangerous slips and falls with different combinations of floor and shoe sole. The results showed different tendency of backward slip in take off phase being significant in generating dangerous slips and falls because backward slip in the takeoff phase affected gait pattern disturbances seriously. resulted in dangerous falls. Fast toe velocity increased the severity of backward slip and confirmed the significance of backward slip in generating dangerous slips and falls. As a result, this study recommends the utilization of backward slip in the measurement of floor slipperiness.

• 대한기계학회논문집B
• /
• 제33권3호
• /
• pp.164-169
• /
• 2009

The slip velocity and the temperature jumps for low-speed flow in microchannels are investigated using Langmuir slip boundary condition. This slip boundary condition is suggested to simulate micro flow. The current study analyzes Langmuir slip boundary condition theoretically and it analyzed numerically micro-Couette flow, micro-Poiseuille flow and grooved microchannel flow. First, to prove validity for Langmuir slip condition, an analytical solution for micro-Couette flow is derived from Navier-Stokes equations with Langmuir slip conditions and is compared with DSMC and an analytical solution with Maxwell slip boundary condition. Second, the numerical analysis is performed for micro-Poiseuille flow and grooved microchannel flow. The slip velocity and temperature distribution are compared with results of DSMC or Maxwell slip condition and those are shown in good agreement.

• International Journal of Automotive Technology
• /
• 제7권6호
• /
• pp.681-686
• /
• 2006

The current flat type side slip tester measures only the total side slip. Therefore, measurement techniques which can be used to determine the side slip for each alignment element were examined. Because the side slip related to the camber angle varies depending on the unit load per travel wheel while the side slip related to the toe angle does not on the unit per travel wheel, but depends only on the direction of the tire, the side slip for each alignment element can be determined separately.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2004년도 춘계 학술발표회 제16권1호
• /
• pp.104-107
• /
• 2004

The crack widths of reinforced concrete flexural members are influenced by repetitive fatigue loadings. The bond stress-slip relation is necessary to estimate these crack widths realistically. The purpose of the present study is, therefore, to propose a realistic model for bond stress-slip relation under repeated loading. To this end, several series of tests were conducted to explore the bond-slip behavior under repeated loadings. Three different bond stress levels with various number of load cycles were considered in the tests. The present tests indicate that the bond strength and the slip at peak bond stress are not influenced much by repeated loading if bond failure does not occur. However, the values of loaded slip and residual slip increase with the increase of load cycles. The bond stress after repeated loading approaches the ultimate bond stress under monotonic loading and the increase of bond stress after repeated loading becomes sharper as the number of repeated loads increases. The bond stress-slip relation after repeated loading was derived as a function of residual slip, bond stress level, and the number of load cycles. The models for slip and residual slip were also derived from the present test data. The number of cycles to bond slip failure was derived on the basis of safe fatigue criterion, i.e. maximum slip criterion at ultimate bond stress.

• 대한기계학회논문집A
• /
• 제30권3호
• /
• pp.295-301
• /
• 2006

The wheel slip control systems are able to control the braking force more accurately and can be adapted to different vehicles more easily than conventional ABS systems. In order to achieve the superior braking performance through the wheel-slip control, real-time information such as the tire braking force at each wheel is required. In addition, the optimal target slip values need to be determined depending on the braking objectives such as minimum braking distance, stability enhancement, etc. In this paper, a robust wheel slip controller is developed based on the adaptive sliding mode control method and an optimal target slip assignment algorithm. An adaptive law is formulated to estimate the longitudinal braking force in real-time. The wheel slip controller is designed using the Lyapunov stability theory and considering the error bounds in estimating the braking force and the brake disk-pad friction coefficient. The target slip assignment algorithm is developed for the maximum braking force and searches the optimal target slip value based on the estimated braking force. The performance of the proposed wheel-slip control system is verified In simulations and demonstrates the effectiveness of the wheel slip control in various road conditions.

• 대한기계학회논문집B
• /
• 제27권8호
• /
• pp.1097-1104
• /
• 2003

The current study analyzes Langmuir slip boundary condition theoretically and it is tested in practical numerical analysis for separation-associated flow. Slip phenomenon at the channel wall is properly implemented by various numerical slip boundary conditions including Langmuir slip model. Compressible backward-facing step flow is compared to other analysis results with the purpose of diatomic gas Langmuir slip model validation. The numerical solutions of pressure and velocity distributions where separation occurs are in good agreement with other numerical results. Numerical analysis is conducted for Reynolds number from 10 to 60 for a prediction of separation at T-shaped micro manifold. Reattachment length of flows shows nonlinear distribution at the wall of side branch. The Langmuir slip model predicts fairly the physics in terms of slip effect and separation.

• Journal of Mechanical Science and Technology
• /
• 제15권9호
• /
• pp.1274-1280
• /
• 2001

The fretting wear behavior of the contact between Zircaloy-4 tube and Inconel 600, which are used as the fuel rod cladding and grid, respectively, in PWR nuclear power plants was investigated in air. In the study, number of cycles, slip amplitude and normal load were selected as the main factors of fretting wear. The results indicated that wear increased with load, slip amplitude and number of cycles but was affected mainly by the slip amplitude. SEM micrographs revealed the characteristics of fretting wear features on the surface of the specimens such as stick, partial slip and gross slip which depended on the slip amplitude. It was found that fretting wear was caused by the crack generation along the stick-slip boundaries due to the accumulation of plastic flow at small slip amplitudes and by abrasive wear in the entire contact area at high slip amplitudes.