• Journal of Communications and Networks
• /
• 제14권2호
• /
• pp.195-198
• /
• 2012

An efficient sliding window algorithm employing an adaptive-length guard window for turbo decoders is proposed. The proposed algorithm results in significant complexity reductions, especially for small sliding window lengths where the additional computational complexity required for the guard window is critical.

• Transactions of Materials Processing
• /
• 제27권3호
• /
• pp.160-164
• /
• 2018

The success of warm forming of Mg alloy sheets is very dependent on its frictional behavior at elevated temperatures. The effects of contact pressure and sliding length on the frictional characteristics of AZ31B Mg alloy sheet were investigated at elevated temperature and at room temperature. The contact pressure range for the friction test was determined through FE analysis of the roof panel which is a candidate for Mg alloy application. According to the experimental results, the frictional behavior of the Mg alloy sheet is equally highly influenced by both sliding length and contact pressure at room temperature. At elevated temperatures, however, the sliding length has a more dominant influence on the frictional characteristics of the Mg alloy sheet than the contact pressure, if the contact pressure is lower than a certain level.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• 제30권4C호
• /
• pp.185-190
• /
• 2005

In IS-95 and IMT-2000 systems using variable code rates and constraint lengths, this paper limits code rate 1/2 and constraint length 3 and realizes forward real-time decoder using Sliding-Window with decoding length 6 and PVSL(Prototype Vector Selecting Logic), LVQ(Learning Vector Quantization) in Neural Network. In comparison condition to theoretically constrained AWGN channel environment at $S/(N_{0}/2)=1$ I verified the superiority of forward real-time decoder through hard-decision and soft-decision comparison between Viterbi decoder and forward real-time decoder such as BER and Secure Communication and H/W Structure.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• 제32권5A호
• /
• pp.426-432
• /
• 2007

The MAP algorithm is designed and implemented through the sliding window method for turbo decoding. First, the implementation issues, which are the length of the sliding window and the normalization method of state metrics are reviewed, and their optimal values are obtained by the simulation. All component schemes of the decoder including the branch metric evaluator are also presented. The proposed MAP architecture can be easily redesigned according to the size of sliding window, that is, sub-frame length because of its simplicity on buffer control.

• Journal of Korean Association for Spatial Structures
• /
• 제23권4호
• /
• pp.35-42
• /
• 2023

The purpose of this study is to experimentally analyze the seismic performance of column with RSB (Replaceable Steel Brace), a steel brace system with slot length as a variable. To evaluate the seismic performance of the RSB, three specimens were manufactured and subjected to cyclic loading tests. The length of the sliding slots were considered to be 5 mm and 10mm to enable the brace to resist the load from the initiation of flexural crack and shear crack. As a result of the test, the specimen reinforced with the RSB showed improved maximun load and effective stiffness, and energy dissipation capacity compared to the non-reinforced specimens. The specimens with 5mm sliding slot showed little difference in test result compared to the specimen with a 10mm sliding slot, indicating that the length of sliding slot has little influence on the effectiveness of RSB.

• Geomechanics and Engineering
• /
• 제13권4호
• /
• pp.621-640
• /
• 2017

The double-row long-short composite anti-sliding piles system is an effective way to control the landslides with high thrust. In this study, The double-row long-short composite anti-sliding piles with different load segment length (cantilever length) and different pile row spacing were studied by a series of physical tests, by which the influences of load segment length of rear-row piles as well as pile row spacing on the mechanical response of double-row long-short composite anti-sliding pile system were investigated. Based on the earth pressures in front of and behind the piles obtained during tests, then the maximum bending moments of the fore-row and the rear-row piles were calculated. By ensuring a equal maximum moments in the fore-row and the rear-row piles, the optimum lengths of the rear-row piles of double-row long-short composite system under different piles spacing were proposed. To investigate the validity of the reduced scale tests, the full-scale numerical models of the landside were finally conducted. By the comparisons between the numerical and the physical test results, it could be seen that the reduced scale tests conducted in this study are reliable. The results showed that the double-row long-short composite anti-sliding piles system is effective in the distribution of the landslide thrust to the rear-row and the fore-row piles.

• Proceedings of the IEEK Conference
• /
• 대한전자공학회 2003년도 하계종합학술대회 논문집 Ⅳ
• /
• pp.2192-2195
• /
• 2003

This parer proposes a power-line phase measurement algorithm which is based on the recursive implementation of sliding-DFT. Usage of the single DFT coefficient in the conventional sliding-DFT based power-line phase measurement brings a significant error propagation when implemented in hardware with finite word-length arithmetic operations. The proposed algorithm utilizes all the N-point DFT coefficients in the recursion. Performance degradation caused by the finite word- length implementation of the algorithm is analyzed and verified with computer simulations. The robustness of the proposed phase measurement algorithm against the erroneous implementation is also confirmed by the performance analysis and simulation.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• 제24권8A호
• /
• pp.1218-1226
• /
• 1999

In decoding the turbo codes, the sliding window BCJR algorthm, derived from the BCJR algorithm, permits a continuous decoding of the coded sequence without requiring trellis fermination of the constituent codes and uses reduced memory span. However, the number of computation required is greater than that of BCJR algorithm and no study on the effect of the window length has been reported. In this paper, we propose an eddicient sliding window type scheme which maintains the advantages of the conventional sliding window algorithm, reduces its computational burdens, and improves is BER performance. A guideline is first presented to determine the proper window length and then a computationally efficient sliding window BCJR algorithm is obtained by allowing the window to be forwarded in multi-step. Simulation results show that the proposed scheme outperforms the conventional sliding window BCJR algorithm with reduced complexity. It gains 0.1dB SNR improvements over the conventional method for the constraint length 3 and BER $10^{-4}$

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1996년도 Proceedings of the Korea Automatic Control Conference, 11th (KACC); Pohang, Korea; 24-26 Oct. 1996
• /
• pp.405-408
• /
• 1996

Several papers have already been reported on the flexible manipulator with constant arm length. Some of industrial manipulators, however, have sliding joints. It means that the length of their arm or link varies with time. This paper discusses the trajectory contro lof such a manipulator model, and shows some of the experimental results.

• Korean Journal of Agricultural Science
• /
• 제25권1호
• /
• pp.97-106
• /
• 1998

This study was carried out to investigate the problem of analysis method of circular sliding, which uses a high rate to work out a countermeasure for landslides. The results of this study were summarized as follows : 1. As a result of the analysis of sliding surface along the soil layers in forty model slopes, the boundary layer in weathered soil and weathered rock indicated a very high possibility of sliding than in other places. 2. Because most landslides in Korea occur along the discontinuity face at the boundary of soil layers, below 2m. from land surface, it is a good method for safe design to work the countermeasure for these kinds of landslides in cutting slopes. 3. When the inclination of slopes is fixed and the length of slopes is changed, the cercular sliding slopes were more safe as the soil layers are more shallow and the length of slopes are shorter, but the safety ratio of infinite sliding slopes was same as the other even though their length of slopes was different. 4. As a result of the analysis by cercular sliding analysis method and infinite sliding analysis method with some condition that the inclination of slopes was $30^{\circ}$ degree, because most landslides in Korea occur at this condition, these methods indicated different results to each other as well as cercular sliding analysis method showed too much safety ratio than infinite sliding analysis method.