• Journal of Biosystems Engineering
• /
• v.1 no.1
• /
• pp.17-48
• /
• 1976

In analyzing the operational characteristics of a rice whitening machine, the internal radial pressure of the machine was measured using strain gage equipment. Changes in cylinder and feed screw configurations, screen type, cylinder speed and counter-pressure levels were examined to determine their impact on the quality and quantity of milled rice and the performance of the machine. The results are summarized as follows: 1. The internal radial pressure in the whitening chamber varied with the surface condition of the grain being processed. During the first or second pass through the machine, pressure was relatively low, reached a maximum after two to three passes with combinations I and II, three to six with combination III and then began to fall. 2. The pitch of the feed screw and the size of the feed gate opening which determine the rate of entry of grain into the whitening chamber, appeared to be the most important factor aff-::cting the degree of radial pressure, quality and quantity of milled rice and the efficiency of the machine. Using a feed screw with a wide pitch (4.8cm), radial pressure was relatively high and head rice recovery ratio \vere quite low. In this case capacity and machine effic\ulcorneriency were much higher than obtained when using a feed screw with a narrow pitch (2.3cm). Very significant responses in radial pressure, head rice recovery rates and machine capacity were observed with changes in cylinder speed and counter-pressure levels when using the wide pitch feed screw. 3. The characteristics of the screen which surrounds the whitening chamber had an important effect on whitening efficiency. The existence of small protuberances on the original screen resulted in significant increases in both machine capacity and efficiency but without a significant decrease in head rice recovery or development of excessive radial pressure. Further work is required to determine the effects of screen surface conditions and the shape of the cylinderical steel roller on the rate of bran removal, machine efficiency and recovery rates. The size of the slotted perforations 0:1 the screen affects total milled rice recovery. The opening size on the original screen was fabricated to accommodate the round shape of Japonica rice varieties but was not suitable for the more slender Indica type. Milling Indica varieties with this screen resulted in a reduction in total milled rice recovery. 4. An increase in cylinder speed from 380 to 820 rpm produced a positive effect on head rice recovery for all machine combinations at every level of counter-pressure used in the tests. Head rice recovery was considerably lower at 380rpm using a wide screw pitch when compared to the results obtained at speeds from 600 to 820 r.p.m. The effects of cylinder speed On radial pressure, capacity and machine efficiency showed contrasting results, depending on the width of the feed screw pitch. With a narrow feed screw pitch (2.3cm), a direct proportional relationship was observed bet\ulcornerween cylinder speed and both radial pressure and machine efficiency. In contrast, using a 4.8 centimeter pitch feed roller produced a series of inverse relationships between the above variables. Based on the results of this study it is recommended when milling Indica type long grain rice varieties that the cylinder speed of the original machine be increased from 500-600 rmp up to a minimum of 800 rpm to obtain a greater abrasive effect between the grain and the screen. The pitch of the feed screw should be also reduced to decr\ulcornerease the level of internal radial pressure and to obtain higher machine efficiency and increased quality of milled rice with increased cylinder speeds. Further study on the interaction between cylinder speed and feed screw pitch is recommended. 5. An increase in the counter pressure level produced a negative effect On the head rice recovery with an increase in radial pressure, capacity, and machine efficiency over all combinations and at every level of cylinder speed. 6. Head rice recovery rates were conditioned primarily by the pressure inside the whitening chamber. According to the empirical cha racteristics curve developed in this study, the relationships of head rice recovery ($Y_h$) and machine capacity ($Y_c$/TEX>) to internal radial pressure ($X_p$) followed an inverse quadratic function and a linear function respectively: $$Y_h^\Delta=\frac{1}{{1.4383-0.2951X_p^\ast+0.1425X_p^{\ast\ast}}^2} , (R^2=0.98)$$ $$Y_c^\Delta=-305.83+374.37X_p^{\ast\ast}, (R^2=0.88)$$ The correlation between capacity and power consumption per unit of brown rice expressed in the following exponential function: $$Y_c^\Delta=1.63Y_c^{-0.7786^\{\ast\ast}, (R^2=0.94)$$ These relationships indicate that when radial pressure increases above a certain range (1. 6 to 2.0 kg/$cm^2$ based On the results of the experiment) head ricerecovery decrea\ulcornerses in a quadratic relation with a inear increase in capacity but without any decrease in power consump tion per unit of brown rice. On the other hand, if radial pressure is below the range shown above, power consumption increases dramatically with a lin\ulcornerear decrease in capacity but without significant increases in head rice recovery. During the operation of a given whitening machine, the optimum radial pressure range or the correct capacity range should be selected by controlling the feed rate and/or counter-pressure keeping in mind the condition of the grain, particulary the hardness. It was observed that the total number of passes is related to radial pessure level, feed rate and counter-pressure level. The higher theradial pressure the fewer num\ulcornerber of pass required but with decreased head rice recovery. In particular, when using high feed rates, the total number of passes should be increased to more than three by reducing the counter-pressure level to avoid decreaseases in head rice recovery (less than 65 percent head rice recovery on the basis of brown rice) at every cylinder speed. 7. A rapid rise in grain temperature seemed to have a close relationship with the pressure generated inside the whitening chamber and, subsequently with head rice reco\ulcornervery rates. The higher the rate of increase, the lower were the resulting head rice recoveries.

• Korean Journal of Heritage: History & Science
• /
• v.44 no.3
• /
• pp.178-199
• /
• 2011

The ancient tombs found in Bokcheon-dong, Busan originate from the time between the $4^{th}$ and $5^{th}$ centuries, the period of the Three Nations. They are known as the tombs where the Vertical Plate Armour was mainly buried. In 2006, two units of the Vertical Plate Armour were additionally investigated in the tombs No.164 and No.165 which had been constructed at the end of the eastern slope near the hill of the group of ancient tombs in Bokcheon-dong. Throughout this study, the contents of the two units of the Vertical Plate Armour, whose preservation process has been completed, have been arranged, while the group of constructed ancient tombs in Bokcheon-dong from the $4^{th}$ century has been observed through the consideration of the burial pattern. The units of the Vertical Plate Armour from the tombs No.164 and No.165 can be classified as the IIa-typed armor showing the Gyeongju and Ulsan patterns, according to the attribute of the manufacturing technology. Also, they can be chronologically recorded as those from the early period of Stage II among the three stages regarding the chronological recording of the Vertical Plate Armour. While more than two units of the Vertical Plate Armour were buried in the largesized tomb on the top of the hill of the group of ancient tombs, one unit of the Vertical Plate Armour was buried in the small-sized tomb. By considering such a trend, it can be said that in the stage of burying the armor showing the Gyeongju and Ulsan patterns (I-type and IIa-type), different units of the Vertical Plate Armour were buried according to the size of the tomb. However, as the armor showing the Busan pattern (IIb-type) was settled, only one unit was buried. Meanwhile, the tombs No.164 and No.165 can be included in the wooden chamber tomb showing the Gyeongju pattern, which is a slender rectangular wooden chamber tomb with the aspect ratio of more than 1:3. However, according to the trend shown by the buried earthenware, it can be said that there seem to be common types and patterns shared with the earthenware which has been found in the area of Gimhae and is called the one showing the Geumgwan Gaya pattern. In other words, there seem to be close relationships between the subject tombs and the tomb No.3 in Gujeong-dong and the tomb No.55 in Sara-ri, Gyeongju, regarding the types of armor and tombs and the arrangement of buried artifacts. However, the buried earthenware shows a relationship with the areas of Busan and Gimhae. By considering the combined trend of the Gyeongju and Gimhae elements found in one tomb, it is possible to assume that the group of constructed ancient tombs in Bokcheon-dong used to be actively related with both areas. It has been thought that the Vertical Plate Armour used to be the exclusive property of the upper hierarchy until now, since it was buried in the large-sized tomb located on the top of the hill of the group of ancient tombs in Bokcheondong. However, as shown in case of the tombs No.164 and No.165, it has been verified that the Vertical Plate Armour was also buried in the small-sized tomb in terms of such factors as locations, sizes, the amount of buried artifacts and the qualitative aspect. Therefore, it is impossible to discuss the hierarchical characteristic of the tomb just based on the buried units of the Vertical Plate Armour. Also, it is difficult to assume that armor used to symbolize the domination of the military forces. The hierarchical characteristic of the group of constructed ancient tombs in Bokcheon-dong from the $4^{th}$ century can be verified according to the location and size of each tomb. As are sult, the re seem to be some differences regarding the buried units of the vertical plate armour. However, it would be necessary to carry out amore multilateral examination in order to find out whether the burial of the vertical plate armour could be regarded as the artifact which symbolizes the status or class of the deceased.

• (The) Research of the performance art and culture
• /
• no.41
• /
• pp.285-320
• /
• 2020

This study aims to examine the processes of changes of the two main roles, Sangjwa(the young Buddist monk) chum and Omjung(the monk with a boil on his face) chum, performed in Yangju Byeolsandae Nori, on the basis of Chumsawi (dance-movement). Above all, having studied many artistic remains performed by Jo jong sun, Jung han gyu, Park jun seup, Kim sung tae from 1929 to 1942, two main roles, in which Geodeureum chum is now an essential part in almost all performances, were then played only in Kkaekki chum to Taryong Jangdan without performances of Geodeureum chum. In case of Sangjwa chum, players had performed ad libitum and without restraint only on the basis of five sorts of Kkaekki chum's movements. In Omjung chum, witty remarks along with the drama had become more important factors than dances. Let alone two main roles, other parts then also showed no big changes in dance performance. Performers just tried to maintain its slender existence within stifling atmosphere because of oppressions and restraints during the Japanese imperialism. After the restoration of independence in 1945, Kim sung tae and his disciples made a great effort on the restoration of Talnori. During the Korean war, many players also endeavored to keep a good track of Talnori, teaching and training their young followers. Especially performers such as Park jun seup, Park sang hwan, Kim sung tae, and Lee jang sun put much more efforts on restoring Talnori. From that time, Geodeureum chum began to appear in two main roles' performances. In Sangjwa's performances, Byeogsa ritual dance, which was performed to Taryong Jangdan, changed into performances to Yeombul Jangdan, and Kkaekki chum -originally slow and ritual dance, became very fast and active one. Geodeureum chum, called Yongteulim, was added in Omjung chum, so that dance had more important role in performance. Even at this time, dance movements were not clearly and completely organized and arranged, because Geodeureum chum's performance was not clearly defined as orderly dance movements but was regarded as just a movement. After Geodeureum chum being designated as a cultural treasure, Lee byeong kwon took over the task from Park sang hwan, Sangjwa chum's performer, so Geodeureum chum became much more well organzied, arranged and orderly. Geodeureum chum played by Sangjwa had almost the same order of scenes and movements as Geodeureum chum played by Yeonnip. Based on this performance, the order of dances and movements was consistently arranged and settled. Following Park jun seup's performances, Jangsam was more widely applied and used in Omjung chum than ever before, so Omjung chum became much more organized and arranged. Well-arranged Omjung chum had also almost the same dances and movements as Nojang chum's. Yeonnip and Nojang's performances were not directly and intentionally studied and applied to two main roles in Yangju Byeolsandae Nori. Players seemed to borrow those parts naturally through many times of performances. Through their persistent efforts, Jangdan and dance movements have more clearly and completely been organized, establied, and improved through many years' performances. And dance movement can be performed exactly to Jangdan, so we have more complete and orderly types of dance movements. Thanks to many performers' efforts, Sangjwa chum has been established as one that only top performer can play, and Omjung chum has become an integral part in Yangju Byeolsandae Nori.

• Journal of Korean Society of Forest Science
• /
• v.25 no.1
• /
• pp.13-47
• /
• 1975

Among the many species of bamboo, it is well known that the dwarf-type is widely distributed in the tropical regions, and the slender type in temperated zone. In the temperated zone the trees have extensively differentiated into one hundred species in 50 genera. In many oriental countries, the bamboo wood is being used as a material for construction and for the manufacture of technical instruments. The bamboo shoot is also regarded as a good and delicious edible resource. Moreover, recent medical investigation verifies that the sap of certain species of the bamboo is an antibiotic effect against cancer. Fortunately, it is very easy to propagate the bamboo trees by using cutting from southeastern Asian countries. This important resource can further be used as a significant source of pulp, which is becoming increasingly important. The classification system of this significant resource has not been completely established to date, even though its importance has been emphasized. Initiated by Canlevon Linne in the 18th century, a classification method concerning the morphological characteristics of flowers was the first step in developing a classification. But it was not an easy task to accomplish, because this type of classification system is based on the sexual organs in bamboo trees. Because the bamboo has a long life cycle of 60-120 years and classification according to this method was very difficult as the materials for the classification are not abundant and some species have changed, even though many references related to the morphological classification of bamboo trees are available nowadays. So, the certification of bamboo trees according to the morphological classification system is not reasonable for us. Consequently, the classification system of bamboo trees on the basis of endomorphological characteristics was initiated by Chinese-born Liese. And classification method based on the morphological characteristics of the vascular bundle was developed by Grosser. These classification methods are fundamentally related to Holltum's classification method, which stressed the morphology of the ovary. The author investigated to re-establish a new classification method based on the vascular sheath. Twenty-six species in 11 genera which originated from Formosa where used in the study. The results obtained from the investigation were somewhat coordinated with those of Crosser. Many difficulties were found in distinguishing the species of Bambusa and Dendrocalamus. These two species were critically differentiated under the new classification system, which is based on the existence of a separated vascular bundle sheath in the bamboo. According to these results, it is recommended that Babusa divided into two groups by placing it into either subspecies or the lower categories. This recommendation is supported by the observation that the evolutional pattern of the bamboo thunk which is from outward to inward. It is also supported by the viewpoint that the fundamental hypothesis in evolution is from simple to complex. There remained many problems to be solved through more critical examination by comparing the results to those of the classification based on the sexual organs method. The author observed the figure of the cross-sectional area of vascular trunk of bamboo tree and compared the results with those of Grosser and Liese, i.e. A, $B_1$, $B_2$, C, and D groups in classification. Group A and $B_2$ were in accordance with the results of those scholars, while group D showed many differences, Grosser and Liese divided bamboo into "g" type and "h" type according to the vascular bundle type; and they included Dendrocalamus and Bambusa in Group D without considering the type of vascular bundle sheath. However, the results obtained by the author showed that Dendrocalamus and Bambusa are differentiated from each other. By considering another group, "i" identified according to the existence of separated vascular bundle sheath. Bambusa showed to have a separated vascular bundle sheath while Dendrocalamus does not have a separated vascular bundle sheath. Moreover, Bambusa showed peculiar characteristics in the figure of vascular development, i.e., one with an inward vascular bundle sheath and the other with a bivascular bundle sheath (inward and outward). In conclusion, the bamboo species used in this experiment were classified in group D, without any separated vascular bundle sheath, and in group E, with a vascular bundle sheath. Group E was divided into two groups, i.e., and group $E_1$, with bivascular sheath, and group $E_2$, with only an inward vascular sheath. Therefore, the Bambusa in group D as described by Grosser and Liese was included in group E. Dendrocalamus seemed to be the middle group between group $E_l$ and group $E_2$ under this classification system which is summarized as follows: Phyllostachys-type: Group A - Phyllostachys, Chymonobambus, Arundinaria, Pseudosasa, Pleioblastus, Yashania Pome-type: Group $B_2$ - Schizostachyum, Melocanna Hemp-type: Group D - Dendrocalamu Bambu-type: Group $E_1$ - Bambusa ghi.