• 한국방재학회 논문집
• /
• 제2권2호
• /
• pp.105-113
• /
• 2002

강합성 교량은 자중의 감소, 강성의 증대, 장지간의 적용 등의 재료적 특성에 힘입어 1920년대 이래로 사용되어져 왔다. 그러나 연속교의 경우 내부지점부에서 발생하는 부모멘트로 인하여 콘크리트 부분에 균열이 생기고 콘크리트의 건조수축이나 Creep으로 인한 문제들이 제기 됨에 따라 슬랩앵커를 이용한 부분합성교량이 제기 되었다. 부분합성의 경우 어느 정도의 슬립을 허용하여 이러한 문제를 극복할 수 있다. 본 연구에서는 슬랩앵커의 탄성구간에서의 초기 강성값을 실험을 통하여 알아내고, 단순지지인 경우와 연속교의 경우에 대하여 범용 프로그램을 이용하여 슬래브와 강재를 연결시키는 조인트 요소의 강성값을 변화시켜 전단연결재의 강성값에 따른 합성정도와 내부지점부의 콘크리트 슬래브의 인장응력이 어떤 변화양상을 나타내는지 파악하고자 한다.

• Structural Engineering and Mechanics
• /
• 제43권4호
• /
• pp.459-473
• /
• 2012

Post-tensioned concrete voided slab girders are widely used in highway bridge constructions. To obtain greater section hollow rate and reduce the self-weight, the plate thickness of slab girders are designed to be small with the adoption of flat anchorage system. Since large prestress is applied to the anchor end section, it was found that longitudinal shear cracks are easy to occur along the voided slab girder. The reason is the existence of great shearing effect at the junction area between web and bottom (top) plate in the anchor end section. This paper focuses on the longitudinal anti-cracking problem at the anchor end of post-tensioned concrete voided slab girders. Two possible models for longitudinal anticracking analysis are proposed. Differential element analysis method is adopted to derive the solving formula of the critical cracking state, and then the practical analysis method for longitudinal anti-cracking is established. The influence of some factors on the longitudinal anti-cracking ability is studied. Results show that the section dimensions (thickness of bottom, web and top plate) and prestress eccentricity on web plate are the main factors that influence the anti-cracking ability. Moreover, the proposed method is applied into three engineering examples to make longitudinal anti-cracking verification for the girders. According to the verification results, the design improvements for these girders are determined.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2001년도 봄 학술발표회 논문집
• /
• pp.93-98
• /
• 2001

This study is to develop the end anchorage of external steel reinforcement of RC slab bridges. External prestress method using the existing steel is that When the anchorage is installed in slab end, a plenty of anchor bolts were required because the only tangential stress of anchor bolt received a tendon force. Then, for this reason, the wide end anchorage was required and the shape was complicate. But this reinforcement method using method that inserts anchor key at concrete surface cut a groove gets big internal force comparing to the anchorage using existing anchor bolt. Furthermore, the number of anchor bolt for installing apparently will be reduced, and the operation will be convenient because a small anchorage of a simple shape will be received a great tendon force

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2001년도 가을 학술발표회 논문집
• /
• pp.1009-1014
• /
• 2001

This study is to develop the end anchorage of external steel reinforcement of RC slab bridges. External prestress method using the existing steel is that When the anchorage is installed in slab end, a plenty of anchor bolts were required because the only tangential stress of anchor bolt received a tendon force. Then, for this reason, the wide end anchorage was required and the shape was complicate. But this reinforcement method using method that inserts anchor key at concrete surface cut a groove gets big internal force comparing to the anchorage using existing anchor bolt. Furthermore, the number of anchor bolt for installing apparently will be reduced, and the operation will be convenient because a small anchorage of a simple shape will be received a great tendon force.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2013년도 춘계학술대회 논문집
• /
• pp.1355-1356
• /
• 2013

• Structural Engineering and Mechanics
• /
• 제44권6호
• /
• pp.839-856
• /
• 2012

To enable remodeling of the exterior of buildings more convenient, such finishing materials as curtain walls, metal panels, concrete panels or dry stones need to be easily detached. In this respect, this study proposed a new design of the slab for the purposes. In the new design, the sides of the slab were properly modified, and the capabilities of anchors fixed in the modified slab were experimentally tested. In details, a number of concrete specimens with different sizes and compressive strengths were prepared, and the effect of anchors with different diameters and embedment depths applied in the concrete specimens were tested. The test results of the maximum capacities of the anchors were compared with the number of current design codes and the stress distribution was identified. This study found that the embedment depth specified in the current design code (ACI318-08) should be revised to be more than 1.5 times the edge distance. However, with the steel sheet reinforcement, the experiment acquired higher tensile strength than the design code proposed. In addition, for two types of specimens in the tensile strength experiment, the current design code (ACI 318-08) is overestimated for the anchor depth of 75 mm. This study demonstrated that the ideal breakout failure was attainable for the side slot details of a slab with more than 180 mm of a slab thickness and less than 75 mm of an anchor embedment depth. It is expected that these details of the modified slab can be specified in the upgraded construction design codes.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1994년도 가을 학술발표회 논문집
• /
• pp.343-349
• /
• 1994

The purpose of this study is to investigate the mechanical properties of floor slab structures with high-strength and lightweight CFRC panel using fly ash, PAN-derived and Pitch-derived carbon fiber. As a result, the flexural strength of CFRC is remarkably increased by CF contents, but compressive strength of the CFRC is not so increased as flexural strength. The bulk specific gravity is influenced by FA contents more than by CF contents, The compressive strength and the flexural strength are increased by FA contests, but decreased the case of 30% of contents. In order to increasing the flexural-carrying capacity of floor slab structures, it is recommended that the shape of anchor for reinforcement is required type-C and the spacing of anchor is required below 60mm.

• 복합신소재구조학회 논문집
• /
• 제2권1호
• /
• pp.8-14
• /
• 2011

본 연구는 Primary Anchor의 비선형 유한요소해석을 통해 구조적 성능을 파악하는데 목적이 있다. Primary Anchor Unit은 ALC 패널 커튼월과 RC 슬래브 또는 주골조 사이에 연결장치로 사용할 수 있다. 항복강도, 초기강성과 최대하중과 같은 구조적 특성을 구하고 자세히 비교분석하였다.

• 한국강구조학회 논문집
• /
• 제16권3호통권70호
• /
• pp.325-332
• /
• 2004

강합성거더 교량의 단면은 강거더와 콘크리트 슬래브의 합성정도에 따라 각각 비합성, 부분합성 그리고 완전합성 단면들로 구분 할 수 있다. 국내의 경우 강합성거더 교량의 단면을 합성시키기 위하여 일반적으로 전단 연결재 중 스터드를 사용하도록 규정하고 있고, 진단 연결재가 없는 경우 즉 비합성 단면의 경우에는 바닥판 앵커를 설치하도록 경험적으로 규정하고 있다. 그러나 바닥판 앵커를 사용한 단면의 실제 거동은 비합성 거동이 아닌 부분합성의 거동을 나타낸다. 그러한 이유로 본 연구에서는 바닥판 앵커를 사용한 플레이트거더교의 부분합성에 관한 해석 및 실험연구를 수행하였다. 실험연구를 통해서 바닥판 앵커의 초기강성을 산정하였고, 해석연구를 통해서 바닥판 앵커를 사용한 단순 및 2경간 연속 플레이트거더교의 합성정도를 비교$\cdot$분석하였다. 또한, 실험에 의해 산정된 강성 값에 근거하여, 2경간 연속 플레이트거더교에 바닥판 앵커를 적용하였을 때 발생할 수 있는 내부지점부 콘크리트의 인장응력 저감 효과를 검토하였다.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2006년도 추계학술대회 논문집
• /
• pp.508-513
• /
• 2006

Anchor bolt in baseplate fastenings on the slab track is an important component to conform placing and safety of fastenings. Due to the way of load transmission control of fastenings, sometimes anchor bolt has to be applied lateral load. So we have to take care for it when we design. Especially, in the case of anchor bolt which is applied loads repeatedly, we have to consider fatigue failure. If parts of machine are damaged in static loads, stress will exceed the yield strength. So parts could be transformed largely. Therefore because they are visible to the naked eyes, we can replace parts before failure. However, because fatigue failure that are invisible to the naked eyes happen unexpectedly, it's very dangerous. To make a reasonable design of anchor bolts, we will analyze them by changing diameters of anchor bolt, quality of insert, initial gap between anchor bolt and insert, the presence of insert, etc. which affect the stresses of anchor bolts. We can get the maximum and minimum amplitude of stress through the modified Goodman diagram or Smith diagram which represents limit of all strengths and stress components to the average stress. We also tried to show the way of examining the expected th life of anchor bolt briefly through considering above.