• Structural Engineering and Mechanics
• /
• 제82권3호
• /
• pp.369-383
• /
• 2022

In this study, an equivalent boundary conditions (BCs) determination method is developed numerically for a panel reinforced concrete (RC) slab to realistically analyze the deformation and fatigue behaviors of a bridge RC slab. For this purpose, a finite element analysis of a bridge RC slab is carried out beforehand to calculate the stiffness of the bridge RC slab, and then the equivalent BCs for the panel RC slab are determined to achieve the same stiffness at the BCs to the obtained stiffness of the bridge RC slab at the corresponding locations of the bridge RC slab. Moreover, for the simulation of fatigue behaviors, fatigue analysis of the panel RC slab is carried out employing a finite element method based on a numerical model that considers the bridging stress degradation. Both the determined equivalent BCs and the BCs that have been typically applied in past studies are employed. The analysis results confirm that, in contrast to the panel RC slab with typically used BCs, the panel RC slab with equivalent BCs simulate the same bending moment distribution and deformation behaviors of the bridge RC slab. Furthermore, the equivalent BCs reproduce the extensive grid crack pattern in the panel RC slab, which is alike the pattern normally witnessed in a bridge RC slab. Conclusively, the panel RC slab with equivalent BCs behaves identical to the bridge RC slab, and, as a result, it shows more realistic fatigue behaviors observed in the bridge RC slab.

• International Journal of Railway
• /
• 제5권4호
• /
• pp.163-166
• /
• 2012

Many different types of floating slab track have been developed and installed around the world to reduce vibrations and noise originating in the surrounding environment. The main objective of this study is to examine the influence of slab length on behavior of floating slab track based on rail-slab-isolator interaction. The floating slab track is modeled by the connection between rail, slab, isolator, and slab mat in the transition zone. All elements were assembled in a simplified two-dimensional (2D) finite element model (FEM). The maximum length of FST is then investigated based on the maximum additional rail stress criterion as described in UIC 774-3R since no fully accepted design criteria for the slab length in FST systems currently exist.

• 콘크리트학회지
• /
• 제7권4호
• /
• pp.119-128
• /
• 1995

이 연구는 최근 건설공사에서의 인력 및 원가의 절감, 공기의 단축 등을 도모하기 위하여 도입되고 있는 하프슬래브의 실용화를 위한 구조거동을 알아보기 위한 실험적 연구이다. PC 패널의 두께, 트러스메쉬의 형사, 가력하중의 형태를 변수로 총 17개의 시험체를제작하여 PC 패널, 하프슬래브, 하프슬래브-벽체 접합부의 휨성능 실험을 하였다. 실험결과, 부방향 하중을 받는 PC 패널의 휨강도가 설계강도보다 작게 나타났으나 정방향 하중을 받는 PC판넬과 덧침콘크리트의 분리현상이 발견되지 않았으며 휨강도 또한 일체로 타설한 부재와 같은 휨내력을 발현하였다. 따라서, 본 연구에서는동바리를 2.0-2.5m간격으로 설치하고, PC판넬과 덧침콘크리트와의 접합면을 조면처리하고 청결을 유지하면 사용상 문제가 없는 것으로 판단되었다.

• 소음진동
• /
• 제11권2호
• /
• pp.276-284
• /
• 2001

In apartment buildings, floor-impact sound has been regarded as the major source that causes complaints from residents. It is mainly due to the use of light-weight structures and the lack of researches in terms of floor-impact sound. The purposes of this study are analyzing the characteristics of vibration response and sound radiation of 12type void slabs in the improvements void slab by impedance method and finding the fittest improvements void slab on the 12type void slab. The main results of this study are summarized as below: (1) In the $\frac{1}{3}$ octave band level of sound radiation, $\frac{1}{3}$ octave band levels, measured from four-divided improvement void slab(No.8) and eight-divided improvement void slab(No.12), are 10~25 dB lower than that of standard void slab(No.1) in the 1250 Hz. Especially, eight-divided improvement void slab(No.12) is the best void slab in terms of radiation efficiency of sound level. (2) In the correlation relation of acceleration and sound radiation, standard void slab(No.1), four-divided improvement void slab(No.8), SK standard four-hole void slab(No.10), and eight-divided improvement void slab(No.12) are positive correlation relation.

• 한국공간구조학회논문집
• /
• 제12권3호
• /
• pp.89-95
• /
• 2012

바닥슬래브의 처짐과 차음 성능을 개선하기 위하여 포스트텐션 중공슬래브가 최근에 자주 사용되고 있다. 동일한 8m 스팬 1층구조물을, 한 구조물은 일반슬래브(solid slab)로, 다른 구조물은 중공슬래브(void slab)로 2개를 제작하여 각 구조물의 바닥슬래브에 포스트텐션을 도입하였다. 중공슬래브의 고유진동수와 감쇠율의 진동특성을 일반슬래브와 비교하였으며, 포스트텐션 도입 후에 일반슬래브와 중공슬래브 각각에 있어서 고유진동수와 감쇠율의 진동특성을 상호 비교하였다. 210mm의 일반슬래브 보다는 250mm 중공슬래브의 1차 고유진동수가 큰 것을 알 수 있다. 포스트텐션 도입 후에도 중공슬래브의 1차 고유진동수는 일반슬래브 보다 큰 것을 알 수 있다. 일반슬래브와 보이드슬래브의 감쇠율은 포스트텐션 도입 전과 도입 후에 거의 동일한 값을 보이는 것을 확인하였다.

• 한국도로학회논문집
• /
• 제19권6호
• /
• pp.47-56
• /
• 2017

PURPOSES : The purpose of this study is to investigate the stresses of the middle slab in a double-deck tunnel owing to the slab lift to replace the underlying elastic pads during maintenance work. METHODS : The middle slab was divided into three different sections: typical section, expansion joint section, and emergency passageway section. Finite element analysis models of these three sections of middle slab were developed, and the stress distribution and maximum stresses were obtained using the models when the middle slab was lifted to replace the underlying elastic pads. Various slab lifting methods were examined in this study such as one-, two-, and multiple-point lifts, distributed lifts, and one or both slab side edge lifts. RESULTS : When the slab side edge is lifted, the longitudinal stresses of the slab are almost the same as the principal stresses. This implies that the governing stresses are the longitudinal stresses. The maximum stresses with both-edge lifts are generally smaller than those with one-edge lifts at all three sections of middle slab. CONCLUSIONS : If the middle slab in a double-deck tunnel is lifted for maintenance, the slab should be lifted at multiple points along the longitudinal direction to reduce the tensile stresses.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2011년도 춘계학술대회 논문집
• /
• pp.993-997
• /
• 2011

Highlighted is significance of the floating slab track for mitigating vibrations induced by train, together with the recent trends towards speed-up of railways. In the design of the floating slab track, it is more beneficial to increase the slab length since a significant impact can be induced on the train and track at the discontinuous points between slabs with the finite slab length. However, if the slab length is too long, the tensile stress of slab concrete and the additional stress on rail due to the temperature change and shrinkage of concrete slab. Thus it is of great importance to relevantly determine the slab length. In this study, to understand these phenomena and establish the countermeasures, the dynamic behaviors of train and track at the inter-slab discontinuous points have been explored and the effect of dowel joints as one of countermeasures has been analytically investigated.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2003년도 추계학술대회 논문집(II)
• /
• pp.151-156
• /
• 2003

The purpose of this study is to establish the test procedure of concrete slab track and to estimate the performance of newly developed slab track. The basic direction of conceptual design of KRRI Slab track was determined in the viewpoint of running safety, economic efficiency and maintenance costs. Based on the research results, a detailed conceptual design of KRRI slab track is suggested. For the systematic development of slab track, a comparative study is carried out, comparing merits and demerits of each slab type, and used in the design process of slab track. Slab track tests were performed at lab and the slab track system was improved by the experiment result. Site Test also were performed in test slab track.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2016년도 추계 학술논문 발표대회
• /
• pp.7-8
• /
• 2016

The use of half PC slab is increasing to shorten construction period. Because the drying shrinkage of topping concrete is restrained by PC slab, the tensile stress is generated at the topping concrete and the cracks can be occurred at the topping concrete due to drying shrinkage. Therefore, it is important to predict the tensile strain of half PC slab due to drying shrinkage to improve the quality of half PC slab. However, there is no studies on prediction of shrinkage behavior of half PC slab yet. Therefore, in this study, half PC slab was made, and the predictability of tensile strain generated at half PC slab due to drying shrinkage was investigated. The step by step method considering creep was used to estimate the tensile strain of half PC slab. In result, good agreement was obtained between the analytical and experimental values.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2003년도 추계학술대회논문집
• /
• pp.56-59
• /
• 2003

As the slab is longer and lighter, it is more sensitive to the external force so that the vibration of slab and noise induced by the slab vibration is bigger than expected in normal slab. The purpose of this study is to investigate how the dynamic characteristic of slab is different from the normal slab through the system identification and tn evaluate the vibration control performance when the damper system is installed. Finally, we was trying to understand by what mechanism the slab noise is induced from the slab vibration. The relationship between the vibration and the noise of slab is shown by the numerical simulation.