• 한국정보과학회 언어공학연구회:학술대회논문집(한글 및 한국어 정보처리)
• /
• 한국정보과학회언어공학연구회 1998년도 제10회 한글 및 한국어 정보처리 학술대회
• /
• pp.217-221
• /
• 1998

본 논문에서는 한국어의 전산처리를 위한 문법 모형 개발의 일부분으로 HPSG에 기반한 문법 모형의 개발을 시도한다. 문법 모형의 개발에는 ALE(Attribute Logic Engine)를 이용하며, 보문 구조와 보조 용언 구문을 분석하기 위한 사전구조 및 문법 규칙을 제시한다. 그리고 문의 종류 (Sentence Type:ST)와 문계(Sentence Level: SL), 시제, 존대 등을 분석해서 표상하기 위한 유형 계층 및 어휘부, 문법 규칙, 문법 원리 등을 제시한다.

• 한국자동차공학회논문집
• /
• 제13권3호
• /
• pp.10-16
• /
• 2005

Recently, the international regulations about the exhaust emissions of the motorcycle have been strengthened. The electrically controlled fuel injection type motorcycle has been emphasized to meet with this regulation. However, since the pulsation phenomenon happens in the intake port of the motorcycle because of the characteristic of high speed and the smaller layout than the passenger car, there are many difficulties to select the factor about control parameters needed to develop the ECU system. In this paper, the pulsation values measured from the engine test were compared with the calculated one by WAVE, and it was analyzed the pulsation characteristic according to the driving condition and estimated the mass flow rate. This research showed that the lowest point of the pressure gets lowin the low load and the pulsation of pressure were increased in the high load. Also, the simulation program was verified by showing good prediction of the pulsation and air mass flow rate.

• 한국자동차공학회논문집
• /
• 제11권3호
• /
• pp.20-27
• /
• 2003

In this paper, the fuel transport characteristics during transient condition was studied by using a Fast Response Flame Ionization Detector(FRFID). The quantitative measurement method for the inducted fuel mass into cylinder is studied. The inducted fuel mass into the cylinder was estimated by using calculated air-fuel ratio by hydrocarbon concentration of cylinder and air flow model. In order to estimate the transportation of injected fuel from the intake port into cylinder, the wall wetting fuel model was used. The two coefficient $\alpha$,$\beta$) of the wall-wetting fuel model was determined from the measured fuel mass that was inducted into the cylinder at the first cycle after injection cut-off To reduce an air/fuel ratio fluctuation during rapid throttle opening, the appropriate fuel injection rate was obtain from the wall wetting model with empirical coefficients. Result of air/fuel ratio control, air/fuel excursion was reduced.

• 한국자동차공학회논문집
• /
• 제10권5호
• /
• pp.1-8
• /
• 2002

For gasoline engines, a three-way catalytic converter that has the maximum efficiency at stoichiometric air/fuel ratio is used to clean up the exhaust gas. So a precise air/fuel ratio control is necessary to maximize the catalytic conversion efficiency, For a transient condition, a fred-forward air/fuel ratio control method that estimates the air mass inducted into a cylinder is being used. In this study, a fuel injection map that makes an accurate air/fuel ratio control possible was constructed for the very same transient condition. For the same condition above, intake air model and fuel model were refined so that fuel injection values based on air mass through a throttle valve and intake manifold pressure are equal to the map values.

• Journal of Mechanical Science and Technology
• /
• 제16권8호
• /
• pp.1127-1134
• /
• 2002

The effects of pressure and temperature on the autoignition of propane and n-butane blends were investigated using a rapid compression machine (RCM) , which is widely used to examine the autoignition characteristics. The RCM was designed to be capable of varying the compression ratio between 5 and 20 and minimize the vortex formation on the cylinder wall using a wedge-shaped crevice. The initial temperature and pressure of the compressed gas were varied in range of 720∼900 K and 1.6∼ 1.8 MPa, respectively, by adjusting the ratio of the specific heat of the mixture by altering the ratio of the non-reactive components (N$_2$, Ar) under a constant effective equivalence ratio (ø$\_$f/= 1.0) The gas temperature after the compression stroke could be obtained from the measured time-pressure record. The results showed a two-stage ignition delay and a Negative Temperature Coefficient (NTC) behavior which were the unique characteristic of the alkane series fuels. As the propane concentration in the blend were increased from 20% and 40% propane, the autoignition delay time increased by approximately 41 % and 55% at 750 K. Numerical reduced kinetic modeling was performed using the Shell model, which introduced some important chemical ideas, represented by the generic species. Several rate coefficients were calibrated based on the experimental results to establish an autoignition model of the propane and n-butane blends. These coefficients can be used to predict the autoignition characteristics in LPG fueled Sl engines.

• 한국자동차공학회논문집
• /
• 제13권4호
• /
• pp.90-96
• /
• 2005

The improvement of combustion stability is very important because it is closely related to the exhaust emission concentrations as well as the fuel consumption during the cold start of SI engine. In our previous studies, the spark and exhaust valve timings were retarded individually from the baseline case to increase the exhaust gas temperature far fast warmup of a close-coupled catalyst. In the study, it was found that combustion stability during cold start becomes worse when the valve timing is retarded from the baseline conditions. The spark and valve timings were simultaneously changed from the baseline conditions to find out the variation of combustion stability during cold start of an Sl engine. Through the study. retarded spark timing by $5^{\circ}$ CA helps improvement of $COV_{imep}$ by $2\%$ and $15^{\circ}C$ increase of exhaust temperature. Retarded exhaust valve timing makes the exhaust gas temperature increase by $30^{\circ}C$, but it also deteriorates the $COV_{imep}$ by $1\%$.