• 한국생산제조학회지
• /
• 제7권6호
• /
• pp.12-18
• /
• 1998

The optimal design for stiffened laminate composite cylindrical shells under combined loads is studied by a nonlinear mathematical search algorithm. The optimal design is accomplished with the CONMIN. several types of buckling modes with maximum allowable stresses and strains are included as constraints in the optimal design process, such as general buckling, panel buckling with either stringers or rings smeared out, local skin buckling, local crippling of stiffener segments. Rectangular or T type stringers and rectangular rings are used for stiffened laminate composite cylindrical shells.

• 대한기계학회논문집A
• /
• 제20권10호
• /
• pp.3199-3210
• /
• 1996

The buckling and postbuckling behaviors were sutdied analytically and experimentally for stiffened laminated composite panels under compression loading. The panels with I-, blade, -and hat-shapeed stiffeners were investigated. In the analysis, the stiffened panels were anlyzed using the nonlinear finite element method combined with an improved arc-length method. The progressive failure analysis was done by adopting the maximum stress criterion and complete unloading failure model. The effects of the fiber angles were investigated on the buckling and postbuckling behaviors. In the experiment, the web and the lower cap of each stiffener were formed by the continuous lay-up of the skin for cocuring the stiffened panels. Therefore, the separation between stiffener and skin was not found in the junction part even after postbuckling ultimate load and the stiffened panels had excellent postbuckling load carrying capacity. A shadow moire thchnique was used to monitor the out-of-plane deformations of the panels. The piezoelectric films were attached to the panels to get the failure characteristics of the panel. The analytical results on the buckling load, postbuckling ultimate load, and failure pattern showed good agreement with the experimental results.

• 대한기계학회논문집
• /
• 제16권4호
• /
• pp.630-648
• /
• 1992

본 연구에서는 여러가지 하중조건하에서 단순지지된 보강원통셸의 최소중량화 설계문제를 CONMIN을 사용하여 해석하고, 일반적인 대칭적층[0/.+-..theta./90]$_{s}$ 의 복합 적층원통셸, 복합적층honeycomb sandwich원통셸, 그리고 보강된 복합적층원통셸의 최 소중량화 설계문제에도 확장 적용한다. 설계변수(design variable)로는 등방성재료 인 경우와 복합적층인 경우 최대 9개, 부등제한조건으로는 전체좌굴(general buckling ), 준전체좌굴(panel buckling), 판 및 보강재의 국부좌굴(local cripping), 로링모드 (rolling mode), 그리고 응력과 변형률제한 등의 성질제한조건(behavior constraints) 과 설계변수의 상, 하한을 나타내는 기하학적 제한(side constraints)등 최대 32개를 설정한다. 본 최소중량화 설계예에서는 보강재의 최적단면형상을 검토하기 위하여 직사각형(R)형, I형, 그리고 T형 단면 등의 보강재들을 사용한다.

• 한국항공우주학회지
• /
• 제48권9호
• /
• pp.671-680
• /
• 2020

본 연구에서는 복합형 회전익 항공기 동체의 설계를 위해 확장된 보 해석을 기술한다. 개발된 보 접근 방법은 등가 보강재 층 방법을 사용하여 보강재로 구성된 동체의 해석이 가능하다. 통합 정식화 보 이론에 기반하여 외피의 두께 및 적층 고려 방법을 제시하였다. 보강재가 고려된 동체에 대해 등가 보강재 층 방법을 적용하여 해석을 수행하였고, 보강재의 제원에 관한 예비 연구 결과를 도출하였으며 상용 프로그램을 이용하여 검증 및 비교를 수행했다.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2004년도 춘계학술발표대회 논문집
• /
• pp.91-94
• /
• 2004

A cyclocopter with the cycloidal blades system can be the type of UAV which can combine the high-speed characteristics of the conventional airplane with the low-speed characteristics of the helicopter. The cycloidal blades system, which can be described as a horizontal rotary wing, offers powerful thrust levels, and a unique ability to change the direction of the thrust almost instantly. Rotor blades are designed to withstand tremendous transverse centrifugal loadings, and responding to a number of aerodynamic harmonic vibratory forcing frequencies. To reduce the weight and increase the strength, the blades are made of composite materials. The blades consist of the skin, spar, and trailing stiffener. In this study, static and dynamic behaviors of cyclocopter rotor blades are analyzed by using MSC/NASTRAN.

• 한국군사과학기술학회지
• /
• 제23권6호
• /
• pp.533-541
• /
• 2020

This study using ABAQUS investigates the nonlinear vibration responses when thermal and random acoustic loads are applied simultaneously to the stiffened composite panels. The nonlinear vibration analyses are performed with changing the number of stiffeners, and layup condition of the skin panel. The panel and stiffeners both are modeled using shell elements. Thermal load (ΔT) is assumed to have the temperature gradient through the thickness direction of the stiffened composite panel. The random acoustic load is represented as stationary white-Gaussian random pressure with zero mean and uniform magnitude over the panels. The thermal postbuckling analysis is conducted using RIKS method, and the nonlinear dynamic analysis is performed using Hilber-HughesTaylor time integration method. When ΔT = 25.18 ℃ and SPL = 105 dB are applied to the stiffened composite panel, the effect of the number of stiffener is investigated, and the snap-through responses are observed for composite panels without stiffeners and with 1 and 3 stiffeners. For investigation of the effect of layup condition of the skin panel, when ΔT = 38.53 ℃ and SPL = 110 dB are applied to the stiffened composite panel, the snap-through responses are shown when the fiber angle of the skin panel is 0°, 30°, and 60°.

• Composites Research
• /
• 제31권6호
• /
• pp.323-331
• /
• 2018

스테인리스 강으로 제작된 요철핀의 보강이 복합재 모자형 체결부의 풀오프 강도에 미치는 영향을 시험으로 연구하였다. 요철핀에는 물리적, 화학적 표면처리를 수행하였고, 체결부의 외피와 보강재가 만나는 영역에 두께방향으로 핀을 삽입하였다. 모자형 체결부 시편은 요철핀을 포함하여 일체성형으로 제작하였다. 사용된 요철핀의 지름은 0.3, 0.5, 0.7 mm로 세 가지이다. 핀의 삽입밀도는 외피와 보강재가 만나는 면적 기준으로 0.5, 2.0% 두 가지이다. 요철핀과 일반핀의 효과를 비교하기 위하여 0.3 mm 일반핀을 2.0% 밀도로 삽입한 시편을 추가로 제작하여 시험을 수행하였다. 0.3, 0.5, 0.7 mm의 요철핀을 0.5%의 밀도로 삽입한 시편의 강도는 보강되지 않은 시편 대비 각각 45, 19, 9% 높게 나타났고, 2.0% 밀도의 경우 강도는 각각 127, 45, 11% 높게 나타났다. 시험 결과 지름이 동일할 경우 밀도가 높을수록, 밀도가 동일할 경우 지름이 작을수록 보강효과가 더 높게 나타나는 것을 알 수 있었다. 요철핀과 일반핀의 효과를 비교한 결과 2.0% 밀도로 0.3 mm 직경의 핀을 이용하여 보강할 경우, 요철핀 보강시편이 일반핀 보강 시편보다 64% 높은 강도를 보였다. 본 연구의 결과로부터 요철핀 보강이 복합재 모자형 체결부의 풀오프 강도 향상을 위한 효과적인 방법이 될 수 있음을 확인하였다.

• 한국정밀공학회지
• /
• 제23권6호
• /
• pp.136-142
• /
• 2006

Optimization of the aircraft panel assembly constructed by skin and stringers is investigated. For the design of panel assembly of the aircraft structure, it is necessary to determine the best shape of the stringer which accomplishes lowest weight under the condition of no instability. A panel assembly can fail in a variety of instability modes under compression. Overall modes of flexure or torsion can occur and these can interact in a combined flexural/torsion mode. Flexure and torsion can occur symmetrically or anti-symmetrically. Local instabilities can also occur. The local instabilities considered in this paper are buckling of the free and attached flanges, the stiffener web and the inter-rivet buckling. A program is developed to find out critical load for each instability mode at the specific stringer shape. Based on the developed program, optimization is performed to find optimum stringer shape. The developed instability analysis program is not adequate for sensitivity analysis, therefore RSM (Response Surface Method) is utilized instead to model weight and instability constraints. Since the problem has many local minimum, Genetic algorithm is utilized to find global optimum.

• Design & Manufacturing
• /
• 제11권2호
• /
• pp.15-19
• /
• 2017

Carbon fiber reinforced plastic (CFRP) is applied as structural material. CFRP is excellent in plane strength / stiffness and don't haves rust. Lightweight, rigid and robust at the same time as transportation material. Aluminum alloy and reinforcement material The application is increasing rapidly. In this study, the prototype of a semi - Monocoque structure frame, Longeron, Stringer, Skin of the aircraft, restraining the rigidity Clips of the aircraft was designated as the target product and the experiment was conducted. ln the experiment, (1) For CFRTP 3 points, data on heating, transfer, and cooling were measured using Thermo Couple, and optimum temperature required for flexible state was obtained. Heating was performed at a temperature 15% higher than the provided temperature. (2) By using a pneumatic press during molding, by dividing LH, center and RH according to the cooling time, thickness parameter of the target product due to the load is measured, and thickness control and time-deviations were analyzed and cross sections were observed with a low magnification microscope.

• Advances in Computational Design
• /
• 제6권1호
• /
• pp.15-30
• /
• 2021

With improvement in innovative manufacturing technologies, it became possible to fabricate any complex shaped structural design for practical applications. This allows for the fabrication of curvilinearly stiffened pressure vessels and pipes. Compared to straight stiffeners, curvilinear stiffeners have shown to have better structural performance and weight savings under certain loading conditions. In this paper, an optimization framework for designing curvilinearly stiffened composite pressure vessels and pipes is presented. NURBS are utilized to define curvilinear stiffeners over the surface of the pipe. An integrated tool using Python, Rhinoceros 3D, MSC.PATRAN and MSC.NASTRAN is implemented for performing the optimization. Rhinoceros 3D is used for creating the geometry, which later is exported to MSC.PATRAN for finite element model generation. Finally, MSC.NASTRAN is used for structural analysis. A Bi-Level Programming (BLP) optimization technique, consisting of Particle Swarm Optimization (PSO) and Gradient-Based Optimization (GBO), is used to find optimal locations of stiffeners, geometric dimensions for stiffener cross-sections and layer thickness for the composite skin. A cylindrical pipe stiffened by orthogonal and curvilinear stiffeners under torsional and bending load cases is studied. It is seen that curvilinear stiffeners can lead to a potential 10.8% weight saving in the structure as compared to the case of using straight stiffeners.