• Journal of the Korean Society of Mechanical Technology
• /
• v.13 no.4
• /
• pp.9-14
• /
• 2011

The flow rate analysis for sanitary fixtures has been studied to determine the water supply piping system and size. The study has been carried out to analyze for a various water supply pressure and piping size theoretically. Also, the study has been carried out to analyze for a various water supply piping system experimentally. The water supply pressure is varied from 0.01MPa to 0.07MPa, and the piping size is varied from 6mm to 15mm. The water supply piping systems are one-to-one, all-loop-type, and bathroom-loop-type water supply piping system. The results indicate that the piping size is able to supply water fully in case of smaller than 15mm if the water supply pressure keep an necessary minimum pressure. And the gap of flow rate is very little for the various water supply piping systems.

• Bulletin of the Korean Space Science Society
• /
• 1995.04a
• /
• pp.21-21
• /
• 1995

The structures of 17GHz microwave burst for bipolar sunspots have investigated. which included the effects of the projected shapes of radio sources as they traverse across the solar disk using a magnetic loop employing a model of solenoid coils. An ensemble of high-energy electrons confined in the loop be assumed. The projected brightnesls distributions of gyrosynchrotron emission in x- and o-modes are computed and converted into total intensity and circular polarization difference at 17GHz for various heliocentric distances using numerical integration of the transfer equation along the line of sight. The results of computations at 17GHz for optical thin case will be presented. and the effects of the orientation of the loop will be discussed in detail, as well as the effect of size, position, Structure, and polarization of the emission. Also the results of the various physical P8lrameters such as the strength of magnetic field. high and low energy cut-off of accelerated electrons. spectral index and density of electrons will be preslmted. After comparing the results of model calculation with observations. we found that the observations can be well explained in terms of a loop model and its projection effect.effect.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.47 no.6
• /
• pp.51-56
• /
• 2010

In this paper, a novel Integer-N phase-delay locked loop(P DLL) architecture has been proposed using a voltage controlled delay line(VCDL). The P DLL can have the LF of one small capacitance instead of the conventional second or third-order LF. The size of chip is $255{\mu}m$ $\times$ $935.5{\mu}m$ including the LF. The proposed P DLL has been designed based on a 1.8V $0.18{\mu}m$ CMOS process and proved by HSPICE simulation.

• Journal of Mechanical Science and Technology
• /
• v.16 no.7
• /
• pp.1019-1028
• /
• 2002

The instability of two-phase loop thermosyphons was investigated experimentally and analytically. Three orifice type inserts were used to study the effect of change in the pressure drop in the flow channel of the TLT on the flow instability and temperature fluctuation. It is observed that a decrease in the size of the orifice insert from 3.7 mm (no insert) to 0.71 mm drastically reduced the fluctuation of the temperature, especially at the evaporator section of the TLT. With the orifice type insert of 0.71 mm for the TLT, the overall temperature fluctuation was almost completely eliminated, especially at higher power input to the TLT The analysis based on the Kelvin-Helmholtz instability theory seems to predict reasonable well the loop stability state of the TLT with experimentally determined constant factors.

• Proceedings of the SAREK Conference
• /
• 2008.11a
• /
• pp.33-38
• /
• 2008

A ground-loop heat exchanger in a ground source heat pump system is an important unit that determines the thermal performance of a system and its initial cost. The Size and performance of this heat exchanger is highly dependent on ground thermal properties. A proper design requires certain site-specific parameters, most importantly the ground effective thermal conductivity, the borehole thermal resistance and the undisturbed ground temperature. This study was performed to investigate the effect of some parameters such as borehole lengths, various grouting materials and U-tube configurations on ground effective thermal conductivity. In this study, thermal response tests were conducted using a testing device with 9-different ground-loop heat exchangers. From the experimental results, the length of ground-loop heat exchanger affects to the effective thermal conductivity. Among the various grouting materials, the bentonite-based grout with silica sand shows the largest thermal conductivity value.

• Journal of ILASS-Korea
• /
• v.7 no.2
• /
• pp.31-36
• /
• 2002

According to the improvement of PC performance, it is expected that calorific value, which causes PC to malfunction, is increased. Therefore, the development of new cooling system is recently required. As the method to solve this problem, we applied loop heat pipe to PC cooling system. The advantage of the loop heat pipe is that it has a small size, light weight, simple shape, long life and it has a good performance on heat transfer, no-noise, wide range of applicable temperature and no supply of power from the outside. It is confirmed that loop heat pipe reduces thermal resistance and has a good performance on PC cooling.

• Journal of the Korea Safety Management & Science
• /
• v.17 no.3
• /
• pp.363-370
• /
• 2015

In this paper, the control technique of the stepping motor using back electromotive force(B-EMF) without encoder is investigated. The stepping motor generally uses the rotary encoder to detect the rotor position. Since this method increases the cost and the motor configuration size, the new closed-loop control method applied for the B-EMF was implemented by using current detect circuit, AD-converter, and micro controller unit(MCU). The control loop of stepping motor became very simplified. The current change of stepping motor measured by the amplifier was measured and analyzed, when the missing step is occurred. Based on the data from current feedback, position errors were compensated and confirmed by using AD-converter.

• Journal of Korea Multimedia Society
• /
• v.12 no.9
• /
• pp.1288-1296
• /
• 2009

This paper is for multi-frequency thin film loop antenna used on smart phone, PMP and PDA like as a multi-media devices. We developed a loop pattern folding methods to reduce a thin film antenna dimension using that mutual coupling folding loop occurs the higher frequency resonation. To reduce the thin film size for loop antenna, we fold the loop pattern repeatedly control the coupling coefficient than generate a not only higher mode resonation but also basic resonation from loop pattern. To realization the thin film folded loop antenna, we used a $30mm{\times}9mm$ PI film the thickness is 20um so that we realize the CDMA850, GPS, DCS, PCS, WCDMA antenna simultaneously and it's radiation efficiency is over 50% and gain is 0dBi.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.39 no.1
• /
• pp.11-19
• /
• 2002

This paper gives an optimal step size of E$\sub$b/ /I$\sub$oT/ for outer-loop power control(OLPC) in IMT-2000 system. The performance of outer-loop Power control is affected greatly by the fixed step size according to the channel environments. Conventional methods are inaccurate because they are decided by expert's experiences and the performance is not proved theoretically. In this paper, we show that IMT-2000 system maintains optimal capacity and QoS by the step size of E$\sub$b/ /I$\sub$oT/ obtained from the discrete-time Markov chain model.

• Journal of Mechanical Science and Technology
• /
• v.19 no.4
• /
• pp.1052-1061
• /
• 2005

A small-scale loop heat pipe (LHP) with polypropylene wick was fabricated and tested for investigation of its thermal performance. The container and tubing of the system were made of stainless steel and several working fluids were tested including methanol, ethanol, and acetone. The heating area was $35\;mm\;{\times}\;35\;mm$ and nine axial grooves were provided in the evaporator to provide vapor passages. The pore size of the polypropylene wick inside the evaporator was varied from $0.5\; {\mu}m\;to\;25\;{\mu}m.$ The inner diameter of liquid and vapor transport lines were 2.0 mm and 4.0 mm, respectively and the length of which were 0.5 m. The size of condenser was $40\;mm\;(W)\;{\times}\;50\;mm\;(L)$ in which ten coolant paths were provided. Start-up characteristics as well as steady-state performance was analyzed and discussed. The minimum thermal load of $10\;W\;(0.8\;W\;/cm^{2})$ and maximum thermal load of $80\;W\;(6.5\;W\;/cm^{2})$ were achieved using methanol as working fluid with the condenser temperature of $20^{\circ}C$ with horizontal position.