• 자원리싸이클링
• /
• 제9권2호
• /
• pp.18-25
• /
• 2000

등방성 영구자석의 제조과정에서 발생되고 있는 barium hexaferrite 폐 자석으로 소결체를 제조하여 물리적, 자기적 특성을 조사하였다. 소결체는 XRD, XRF, SEM 및 자기적 성질을 측정하였다 폐 영구자석을 분쇄하고 조립화하여 폐 영구자석 분말 과립과 시판용 과립을 일정비율로 혼합. 성형하고 소결하였다. 폐 영구자석 분쇄분말의 함량에 따라 자기적 특성은 점차 감소하지만 소결 온도 $1150~1200^{\circ}C$ 에서 영구자석으로서 요구되는 자기적 특성값을 나타내었다.

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2006년도 Extended Abstracts of 2006 POWDER METALLURGY World Congress Part2
• /
• pp.790-791
• /
• 2006

The fracture behavior and mechanical characteristics of sintered rare-earth magnets were investigated. It shows that the fracture behavior and bending strength of the magnets obviously exhibit anisotropy. Sm-Co magnets tend to cleavage fracture in the close-packed (0001) plane or in the ($10\bar{1}1$) plane. The fracture mechanism of $Nd_2Fe_{14}B$ magnet mainly appears to be intergranular fracture. The anisotropy of fracture behavior and mechanical strength of sintered rare-earth magnets is caused mainly by the strong crystal-structure anisotropy and the grain alignment texture. The effects of Nd content, and Pr, Dy substitution on the impact stability of $Nd_2Fe_{14}B$ magnets were also reported.

• Journal of Magnetics
• /
• 제16권3호
• /
• pp.304-307
• /
• 2011

High performance Nd-Fe-B magnets can be manufactured by both sintering and hot deformation. The corrosion behaviors of the magnets prepared by the two processes were compared. Effect of microstructure on the corrosion resistance of Nd-Fe-B magnets was also investigated. A neutral salt spray test (NSS) was performed for the different-processed magnets. The weight losses of the samples after the corrosion test were measured. The corrosion microstructures were observed using a scanning electron microscope. It shows that the corrosion resistance of hot deformed magnets is much better than that of the sintered ones because the grain size and the distribution of Nd-rich phases of the hot deformed magnets are much finer and more uniform than those of the sintered ones. The different microstructure between the sintered and the hot deformed magnets causes the different corrosion behavior.

• 한국자기학회:학술대회 개요집
• /
• 한국자기학회 2015년도 자성 및 자성재료 국제학술대회
• /
• pp.175-175
• /
• 2015

• Archives of Metallurgy and Materials
• /
• 제65권4호
• /
• pp.1293-1296
• /
• 2020

NdFeB anisotropic sintered permanent magnets are typically fabricated by strip casting or melt spinning. In this study, the plastic deformability of an NdFeB alloy was investigated to study the possibility of fabricating anisotropic sintered magnets using gas atomized powders. The results show that the stoichiometric composition Nd₁₂Fe₈₂B₆ softens at high temperatures. The aspect ratio and orientation factor of Nd₁₂Fe₈₂B₆ billets after plastic deformation were found to increase with increasing plastic deformation temperature, particularly above 800℃. This confirms that softening at high temperatures can lead to plastic deformation of Nd₂Fe₁₄B hard magnetic phases.

• 한국자기학회:학술대회 개요집
• /
• 한국자기학회 2017년도 임시총회 및 하계학술연구발표회
• /
• pp.121-121
• /
• 2017

• 열처리공학회지
• /
• 제37권1호
• /
• pp.9-15
• /
• 2024

Nd-Fe-B permanent magnets have been utilized on various industrial fields such as electric vehicles, generator, robots with actuator, etc, due to their outstanding magnetic properties even 10 times better than conventional magnets. Recently, there are many researches that report magnetic properties improved by controlling microstructure through adjusting alloying elements or conducting various processing. Especially, post-sintering annealing (PSA) can significantly improve the coercivity by modifying the distribution and morphology of Nd-rich phase which formed at grain boundaries. In this study, Nd-Fe-B sintered magnets were subjected to primary heat treatment followed by secondary heat treatment at 460℃, 500℃, and 540℃ to investigate the changes in microstructure and magnetic properties with the secondary heat treatment temperature. EBSD analysis was conducted to compare anisotropic characteristics. Through the SEM and TEM observation for analyzing the morphology and distribution of Nd-rich phase, we investigated the relationship between microstructure and magnetic properties of sintered Nd-Fe-B magnets.

• Journal of Magnetics
• /
• 제4권2호
• /
• pp.52-54
• /
• 1999

Injection molding is one of the methods to prepare dielectromagnets-permanent magnets made from hard magnetic powder (or from mixture of powders) bonded by dielectric materials. Magnetic properties of dielectromagnets are worse than those of sintered magnets made from the same hard magnetic powders, but this type of the permanent magnet has many advantages. One of them is simpler technology-easier in comparison to the technology of sintered magnets. The injection molded dielectromagnets do not need any final treatment. This technology permits to control magnetic, thermal and mechanical properties of dielectromagnets. The main chracteristics of dielectormagnets are magnetic properties, however mechanical properties have serious influence onto a range of their applications. The main factors shaping mechanical properties have serious influence onto a range of their applications. The main factors shaping mechanical properties of dielectromagnets are the kind and quantity of resin and the technology. The purpose of this investigateion was to find the correlation between infection conditions and the mechanical properties of dielectromagnets. Influence of two parameters of injection, temperature and pressure on mechanical and magnetic properties of dielectromagnets were not significantly changed. Increasing of pressure of injection also does not influence on mechanical properties of analysed samples, however increasing of temperature of injection significantly improved both compression and bending strength.

• KIEE International Transaction on Electrical Machinery and Energy Conversion Systems
• /
• 제5B권1호
• /
• pp.13-19
• /
• 2005

The performance of two designs of permanent magnet brushless motor, by having self-shielding magnetized magnets or sinusoidally shaped parallel-magnetized magnets with essentially sinusoidal airgap flux distributions, are compared. It is shown that the parallel-magnetized motor with shaped sintered NdFeB magnets can result in a higher airgap flux density and torque density than that of a self-shielding magnetized motor equipped with an anisotropic injection moulded NdFeB ring magnet.

• 한국자기학회지
• /
• 제22권6호
• /
• pp.221-227
• /
• 2012

고특성 영구자석은 하이브리드 및 전기자동차의 구동모터와 풍력발전에 적용되면서 크게 주목을 받고 있다. Nd-Fe-B 영구자석은 가장 높은 최대자기에너지적을 가지고 있지만 고온(${\sim}200^{\circ}C$)의 구동환경에서는 보자력이 급격히 감소하기 때문에 사용할 수 없는 단점을 가지고 있다. 그러므로 큰 보자력을 가지는 Nd-Fe-B 영구자석에 대한 개발이 요구되고 있다. Nd-Fe-B 소결자석에서 보자력을 증가시키기 위해서는 Nd를 Dy 또는 Tb으로 치환하면 쉽게 증가시킬 수 있다. 그러나 이들 원소는 Fe와 반강자성 결합을 하여 잔류자속밀도를 낮추고, 적은 매장량과 한정된 지역에 편재되어 있어 수요급증에 따른 자원수급 및 가격 급등의 문제를 가지고 있다. 따라서, Dy 및 Tb과 같은 중희토류를 사용하지 않거나 최소한의 양을 사용하여 보자력을 증가시키고자 하는 연구가 많이 진행되고 있다. 본 논문에서는 이러한 중희토류 원소의 저감 및 대체에 대한 연구들을 소개하고자 한다.