• 한국연소학회:학술대회논문집
• /
• 한국연소학회 제26회 KOSCO SYMPOSIUM 논문집
• /
• pp.13-19
• /
• 2003

As the environmental pollution becomes serious global problem, the regulation of emission exhausted from automobiles is strengthen. Therefore, it is very important to know how to reduce the NOx and PM simultaneously in diesel engines, which has lot of merits such as high thermal efficiency, low fuel consumption and durability. By this reason, the new concept called as Homogeneous Charge Compression Ignition(HCCI) engines are spotlighted because this concept reduced NOx and P.M. simultaneously. However, it is well known that HCCI engines increased HC and CO. Thus, the investigation of combustion characteristics which consists cool and hot flames for HCCI engines were needed to obtain the optimal combustion condition. In this study, combustion characteristics for direct inject type HCCI engine such as quantity of cool flame and hot flame, ignition timing and ignition delay were investigated to clarify the effects of these parameters on performance. The results revealed that diesel combustion showed the two-stage ignition of cool flame and hot flame, the rate of cool flame increase and hot flame decrease with increasing intake air temperature. On the other hand, the gasoline combustion is the single-stage ignition and ignition timing is near the TDC. In addition mixed fuel combustion showed different phenomenon, which depends on the ratio of gasoline component. Ignition timing of mixed fuel is retarded near the TDC and the ignition delay is increased according to ratio of gasoline.

• 한국자동차공학회논문집
• /
• 제12권1호
• /
• pp.17-24
• /
• 2004

As the environmental pollution becomes serious global problem, the regulation of emission exhausted from automobiles is strengthened. Therefore, it is very important to know how to reduce the NOx and PM simultaneously in diesel engines, which has lot of merits such as high thermal efficiency, low fuel consumption and durability. By this reason, the new concept called as Homogeneous Charge Compression Ignition(HCCI) engines are spotlighted because this concept reduced NOx and P.M. simultaneously. However, it is well known that HCCI engines increased HC and CO. Thus, the investigation of combustion characteristics which consists cool and hot flames for HCCI engines were needed to obtain the optimal combustion condition. In this study, combustion characteristics for direct injection type HCCI engine such as quantity of cool flame and hot flame, ignition timing and ignition delay were investigated to clarify the effects of these parameters on performance. The results revealed that diesel combustion showed the two-stage ignition of cool flame and hot flame, the rate of cool flame increase and hot flame decrease with increasing intake air temperature. On the other hand, the gasoline combustion is the single-stage ignition and ignition timing is near the TDC. In addition mixed fuel combustion showed different phenomenon, which depends on the ratio of gasoline component. Ignition timing of mixed fuel is retarded near the TDC and the ignition delay is increased according to ratio of gasoline.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2011년도 제36회 춘계학술대회논문집
• /
• pp.341-350
• /
• 2011

마이크로 크기의 단일 마그네슘 입자의 연소 해석을 위해 간단하면서도 점화와 연소과정 전체를 모사한 모델을 사용하여 각각의 주요 파라메터별 영향을 도출하는 연구를 수행하였다. 계산에 사용된 모델은 액적 연소의 경우와 유사하게 보존 및 이송 방정식들을 사용하여 모사되었으며 입자의 온도가 1200 K에 도달하면 점화단계를 종료하고 준정상연소 단계로 전환되었다. 선행 연구를 참고하여 주요 파라메터를 선정하였으며 주요 파라메터로는 초기 입자크기, 대류 열전달의 유무, 외기 온도, 압력 등이 선정되었고, 간단한 열역학적 모델임에도 불구하고 정량적으로 실험 데이터와 유사하게 각각의 파라메터의 영향을 평가할 수 있음을 확인하였다.

• 한국산학기술학회논문지
• /
• 제22권6호
• /
• pp.75-82
• /
• 2021

디젤엔진의 열효율을 높이면서 NOx와 PM을 효과적으로 저감시키기 위해 HCCI(Homogeneous Charge Compression Ignition), PCCI(Premixed Charge Compression Ignition), RCCI(Reactivity Controlled Compression Ignition) 등의 저온연소(LTC: Low Temperature Combustion)전략이 개발되어 왔다. 본 연구에서는 저반응성 연료로는 가솔린을 사용하고 고반응성 연료로는 디젤을 사용하는 RCCI 엔진에서 고반응성 연료인 디젤연료의 분사 시기와 이단 분사비율이 성능 및 배출가스에 미치는 영향을 수치해석을 통하여 파악하고자 하였다. 이단 분사 시 첫 번째 분사시기가 너무 진각되면 연소가 느려지면서 연소온도가 낮아져 연소성능이 저하되고 HC, CO가 증가한다. 대략 -60°ATDC 의 분사시기가 연소성능, 배출가스 및 최대압력상승률을 고려하였을 때 가장 최적의 분사시기라고 판단된다. 이단 분사 시 두 번째 분사시기를 변경하였을 때 연소성능 및 배출가스, 최대압력상승률 등을 고려하면 대략 -30°ATDC 부근에서 최적인 것으로 판단된다. 이단 분사 시 분사량 비율은 첫 번째 분사량을 60% 정도로 하였을 때 최적의 결과를 얻었다. 마지막으로 단일 분사보다는 이단 분사한 경우 연소성능 및 배출가스 부분에서 더 효과적인 것으로 판단된다.

• 수산해양기술연구
• /
• 제27권1호
• /
• pp.64-68
• /
• 1991

In this paper, to percuss whether fish oil can substitute for marine fuel oil, the characteristics on the evaporation and ignition of 3 fish oils, Sardine oil, File fish oil and Alaska pollac oil, were investigated experimentally by suspending single fish oil droplel in hot atmosphere, and experiments on methanol and light oil were also carried out to compare the characteristics. The results abtained are summarized as follow; 1) Evaporation and ignition phenomena on the methanol and light oil by the present experimental method agreeded with the results of the earlier investigation. 2) The characteristic on evaporation and ignition of all 3 fish oils took the same pattern; in late stage of evaporation at atmospheric Temperature 55$0^{\circ}C$ droplet rapidly expanded and contracted, and then remained solid corbide, but in case of $650^{\circ}C$ rapidly expanded and ignitied, and then completly burned non-remained solid carbide. 3) As fish oil mixed with light oil (50% weight), in beginning stage of evaporation droplet depended on the characteristics of light oil, but in end stage depended on fish oil. 4) Ignition temperature of fish oil droplets was about 47$0^{\circ}C$, higher than about 25$0^{\circ}C$ of light oil, but atmospheric temperature to ignite droplet was about $650^{\circ}C$, lower than about 75$0^{\circ}C$ of light oil.

• 한국연소학회지
• /
• 제17권2호
• /
• pp.24-31
• /
• 2012

Diesel engines exhaust much more NOx(Nitrogen Oxides) and PM(Particulate Matter) than gasoline engines, and it is not easy to reduce both NOx and PM simultaneously because of the trade-off relation between two components. This study investigated flame characteristics of the partial premixed compression ignition known as new combustion method which can reduce NOx and PM simultaneously. The investigation was performed through the analysis of the flame images taken by a high speed camera from the visible engine which is the modified single cylinder diesel engine. The results obtained through this investigation are summarized as follows; (1) The area of the luminous yellow flame was reduced due to the decrease of flame temperature and even distribution of temperature. (2) The darkish yellow flame zone caused by the shortage of the remaining oxygen after the middle stage of combustion was considerably reduced. (3) Since the ignition delay was shortened, the violent combustion did not occur and the combustion duration became shortened.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집D
• /
• pp.864-870
• /
• 2001

Flame propagation along vortex tube was experimentally investigated. The vortex tube was generated by the ejection of propane from a nozzle through a single stroke motion of a speaker and the ignition was induced from a single pulse laser. Non-reactive flow fields were visualized using shadow technique. From these images, vortex ring size and translational velocity were measured in order to determine the ignition time and position. Flame structure and flame speed were measured using high speed CCD camera. Flame speed was accelerated during the initial stage of flame kernel growth, and reached near constant value during steady propagation period. Near the completion of propagation, flame speed was decelerated and then extinguished. Flame speed along the non-premixed vortex tube was found to be linearly proportional to circulation, which was similar to that of the flame propagation along premixed vortex ring. Ignition position minimally affects the propagation characteristics. These imply that flame is propagating along the maximum speed locus expected to be along stoichiometric contour and also support the existence of tribrachial flames.

• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제53권10호
• /
• pp.625-633
• /
• 2004

This paper proposed a boost input type single stage resonant power supply for driving magnetron device. The proposed power supply can control both input power factor and output power at the same time. Also, because ZVS is achieved using the resonance between leakage inductance and resonant capacitance, switching losses are drastically reduced. To prevent breakdown or moding phenomenon of the magnetron due to excessive starting voltage, variable frequency ignition method is also proposed. Experimental results for the prototype power supply are presented and discussed to verify the validity of the proposed power supply.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2008년도 제30회 춘계학술대회논문집
• /
• pp.187-192
• /
• 2008

A simplified model for an isolated aluminum particle burning in air is presented. Burning process consists of two stages, ignition and quasi-steady combustion (QSC). In ignition stage, aluminum which is inside of oxide film melts owing to the self heating called heterogeneous surface reaction (HSR) as well as the convective and radiative heat transfer from ambient air until the particle temperature reaches melting point of oxide film. In combustion stage, gas phase reaction occurs, and quasi-steady diffusion flame is assumed. For simplicity, 1-dimesional spherical symmetric condition and flame sheet assumption are also used. Extended conserved scalar formulations and modified Shvab-Zeldovich functions are used that account for the deposition of metal oxide on the surface of the molten aluminum. Using developed model, time variation of particle temperature, masses of molten aluminum and deposited oxide are predicted. Burning rate, flame radius and temperature are also calculated, and compared with some experimental data.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2010년도 제35회 추계학술대회논문집
• /
• pp.321-327
• /
• 2010

마이크로 크기의 단일 알루미늄 해석을 위한 간단한 모델을 작성하고, 현상의 주요 파라메터를 도출하는 연구를 수행하였다. 금속 입자의 연소는 점화와 준정상상태의 연소 단계로 구성하였고, 각 단계는 액적 연소의 경우와 유사하게 보존 및 이송 방정식들을 사용하여 모사되었다. 모델은 기존의 실험 데이터와의 엄격한 비교를 통해 신뢰성을 검증하였고, 이 과정에서 현상의 주요 변수를 도출하여 그 영향을 평가하였다. 주요 변수로는 초기 입자크기, 산화 피막 두께, 대류 열전달의 유무, 외기온도, 압력 등이 선정되었고, 간단한 열역학적 모델임에도 불구하고 정량적으로 실험 데이터와 유사하게 각각의 파라메터의 영향을 평가할 수 있음을 확인하였다.