• 대한기계학회논문집
• /
• 제6권3호
• /
• pp.256-260
• /
• 1982

This paper presents the characteristics of fuel spray in a diesel engine. In this paper, in order to obtain spray droplet size in a diesel engine, water was injected into the cylinder at room temperature and pressure by injection system. Spray droplet size was measured by liquid immersion technique with a lubricant used as an immersion liquid for spray water from injection nozzle. In this experiment, single hole type throttle nozzle are used at same operating conditions, which included opening pressure of nozzle, fuel delivery, and injection speed. Sauter mean diameter decrease with the increase of injection pressure and decrease in injection nozzle diameter. The rate of spray penetration increased with increasing injection pressure and diameter of injection nozzle at the constant spray conditions.

• 한국연소학회:학술대회논문집
• /
• 한국연소학회 2013년도 제46회 KOSCO SYMPOSIUM 초록집
• /
• pp.29-31
• /
• 2013

In this study, the characteristics of particulate matters (PM) from diesel and biodiesel fuel combustion was experimentally investigated. The experiment was performed in a single cylinder common-rail compression ignition engine. The fuels were injected at -5 CAD (Crank angle degree) ATDC (After top dead center) with 80 MPa injection pressure. Size distribution of PM was measured by scanning mobility particle sizer (SMPS) and morphology of PM was studied by transmission electron microscopy (TEM). PM from biodiesel shows lower emission level and smaller primary particles.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집D
• /
• pp.896-902
• /
• 2001

To meet strict emission regulation while improving engine performances, common rail injection system which is suitable for electronic control, and capable of controlling injection quantity, timing, rate and pressure individually as well as realizing high pressure has been developed. At present study, a 8L DI diesel engine was converted to a single-cylinder experimental engine allowing optical access through an extended piston and a prototype of common rail injector in progress was applied to the engine. The combustion characteristics of the engine were analysed by using direct images and characteristics of the injector were analysed. We can not say that the results are always the same to general common rail injection system but that they are just characteristics of specific prototype injector.

• 한국자동차공학회논문집
• /
• 제17권5호
• /
• pp.61-66
• /
• 2009

An experimental investigation was conducted to analyze the effects of biodiesel-ethanol and biodiesel-diesel blended fuels on the characteristics of combustion and exhaust emissions, and size distributions of particulate matter in a single cylinder diesel engine. The three types of test fuel were biodiesel and two blended fuels which were added ethanol and diesel by 20 % volume based fraction into biodiesel, respectively. In this study, the injection rate, combustion pressure, exhaust emissions and size distributions of particulate matter were measured under various injection timings and injection pressures. The experimental results show that biodiesel-ethanol blended fuel has lengthened ignition delay and low combustion pressure in comparison with those of biodiesel and biodiesel-diesel blended fuel even if all fuels indicated similar trends of injection rate under equal injection pressures. In addition, the ethanol blended fuel significantly reduced nitrogen oxidies (NOx) and soot emissions. And then the size distribution of particulate matters shows that blended fuels restrain the formation of particles which were beyond the range of 150nm comparison with biodiesel fuel.

• 한국분무공학회지
• /
• 제17권2호
• /
• pp.71-76
• /
• 2012

The aim of this work was to investigate the combustion and nanoparticle emission characteristics of premixed charge compression ignition (PCCI) combustion at various test conditions using a single cylinder common-rail diesel engine. In order to create the homogeneity of fuel-air mixture, the premixed fuel (gasoline) was injected into premixing chamber during the intake process and then the diesel fuel was directly injected into the combustion chamber as an ignition source for the gasoline premixture. From these results, it revealed that the ignition delays and combustion durations were gradually prolonged and the peak combustion pressure were increased because diesel fuel was injected early injection timing with the increase of premixed ratio. In addition, as the increase of premixed ratio, total particle number is generally decreased and particle volume also indicated low levels at the direct injection timing from BTDC $20^{\circ}$ to TDC. At further advanced injection timing, total particle number and volume were generally increased

• 한국수소및신에너지학회논문집
• /
• 제28권1호
• /
• pp.98-105
• /
• 2017

In recent years, compression ignition engine has been equipped with some control devices such as common rail injection system and turbocharger. In order to control the large number of input parameter appropriately in consideration of $NO_x$, HC and engine power as the engine output objectives. The model construction which reproduces the characteristic value of $NO_x$, HC and engine power from input parameter is needed. In this research, the stepwise method was applied to construct the compression ignition engine model. By using the preliminary experimental data of single cylinder compression ignition engine, the prediction model of $NO_x$, HC and engine power on single injection compression ignition engine was built and compared with the main experimental data.

• 한국자동차공학회논문집
• /
• 제13권4호
• /
• pp.145-151
• /
• 2005

Natural gas is one of clean fuels that can replace petroleum-based fuels, because it has low exhaust emission, comparatively high thermal efficiency and abundant deposits. In this addition, owing to high octane number and wide lean flammability limit, it has a strong point to increase the compression ratio. For this reason, the research is being actively executed to increase the generating power and thermal efficiency of the engine by raising the compression ratio through utilization of high octane number relevant to development of CNG engine. In this study, 0.63L single cylinder diesel engine has been used to alter easily compression ratio. Compression ratio has gotten under control by modifying the thickness of gasket between cylinder head and block without major structural modifications. As the result, as compression ratio has increased, generating power and fuel consumption ratio have been improved. As for emission concentration, as compression ratio has increased, THC concentration has been decreased while exhause concentration of NOx increased. In case compression ratio has excessively increased, brake output decrease and cycle variation have been increased. As the result acquired by analyzing brake output, fuel consumption ratio, cycle variation and exhaust, the engine driving condition has acquired $\varepsilon=13$ as the optimal compression ratio in this study.

• 에너지공학
• /
• 제15권3호
• /
• pp.139-145
• /
• 2006

The purpose of this study is to obtain low-emission and high-efficiency in LPG engine with hydrogen enrichment. The objective of this paper is to clarify the effects of hydrogen enrichment in LPG fuelled engine on exhaust emission, thermal efficiency and performance. The compression ratio of 8 was selected to avoid abnormal combustion. To maintain equal heating value of fuel blend, the amount of LPG was decreased as hydrogen was gradually added. The relative air-fuel ratio was increased from 0.8 to 1.3, and the ignition timing was controlled to be at MBT (minimum spark advance for best torque)

• 한국자동차공학회논문집
• /
• 제9권6호
• /
• pp.1-7
• /
• 2001

Recently, several LPG engines for heavy-duty vehicles have been developed, which can replace some diesel engines that are one of a main source for air pollution in urban area. As a preliminary study on the liquid phase LPG injection (hereafter LPLI) system applicable to a heavy duty LPG engine, the engine output and combustion performance were investigated with various combustion chambers and fuel compositions using a single cylinder engine equipped. Experimental results revealed that ellipse, double ellipse and nebula type combustion chamber made a more advantage in breaking swirl flow into small turbulence scale than bathtub type. Especially, performance of nebula type showed most highest efficiency and engine output under lean mixture conditions. An investigation fur various LPG fuel compositions was also carried out, and revealed that the case with 40% propane and 60% butane shows the lowest efficiency at stoichiometry, however, as the mixture became leaner its efficiency increased and became even higher for 100% propane case.

• 한국산학기술학회논문지
• /
• 제21권7호
• /
• pp.692-698
• /
• 2020

본 논문은 커먼레일 단기통 디젤엔진에서 다단 파일럿 분할 분사 전략이 연소 및 배기가스 배출특성에 미치는 영향을 분석하는 데 초점을 두었다. 실린더 내부 최고 압력과 열발생률은 단일분사 조건에서 가장 높았으며, 파일럿 분사량이 균등하게 분할되어 분사 횟수가 증가할수록 감소하는 경향으로 나타났다. IMEP, 엔진 토크 및 연소 효율은 1단 파일럿 분사 조건에서 가장 낮게 나타나는 특성을 보였으나, 다단 파일럿 분할 분사 전략 적용 시 증가하는 경향으로 분석되었다. COV_IMEP는 연소 효율이 가장 낮은 1단 파일럿 분사 조건에서 가장 높았으며, 이는 연소 안정성이 낮다는 것을 의미한다. 배기가스 중 산소농도는 단일분사 조건에서 가장 낮았고, 이산화탄소는 가장 높게 배출되는 특성을 보였다. 다단 분할 분사 전략 적용 시 저온 연소과정이 진행되기 때문에 일산화탄소의 산화율은 낮아지게 되고 배출수준은 증가하는 특성을 보였다. 탄화수소는 국부적으로 농후한 혼합기가 형성되는 단일분사 조건에서 가장 높은 결과를 보였다. 질소산화물은 다단 파일럿 분할 분사 전략 중 3단 파일럿 분사 조건에서 55.6%까지 감소하는 특성을 보였다.