• Advances in nano research
• /
• v.8 no.1
• /
• pp.25-36
• /
• 2020

Rotating systems concern with torsional vibration, and it should be considered in vibration analysis. To do this, the time-dependent torsional vibrations in a single-walled carbon nanotube (SWCNT) under the linear and harmonic external torque, are investigated in this paper. Eringen's nonlocal elasticity theory is considered to demonstrate the nonlocality and constitutive relations. Hamilton's principle is established to derive the governing equation of motion and consequently related boundary conditions. An analytical method, called the Galerkin method, is utilized to discretize the driven differential equations. Linear and harmonic torsional loads, along with determined amplitude, are applied to the SWCNT as the external torques. SWCNT is considered under the clamped-clamped end supports. In free vibration, analysis of small scale effect reveals the capability of natural frequencies in different modes, and this results desirably are in coincidence with another study. The forced torsional vibration in the time domain, especially for carbon nanotubes, has not been done before in the previous works. The previous forced studies were devoted to the transverse vibrations. It should be emphasized that the dynamical analysis of torsion is novel, workable, and at the beginning of the path. The variations of nonlocal parameter, CNT's thickness, and the influence of excitation frequency on time-dependent angular displacement and nondimensional angular displacement are investigated in the context.

• Applied Chemistry for Engineering
• /
• v.33 no.2
• /
• pp.188-194
• /
• 2022

This work presents a non-destructive and straightforward approach to assemble a large-scale conductive electronic film made of a pre-treated single-walled carbon nanotube (SWCNT) solution. For effective electron transfer between the immobilized enzyme and SWCNT electronic film, we optimized the pre-treatment step of SWCNT with p-terphenyl-4,4"-dithiol and dithiothreitol. Glucose oxidase (GOx, a model enzyme in this study) was immobilized on the SWCNT electronic film following the positively charged polyelectrolyte layer deposition. The glucose detection was realized through effective electron transfer between the immobilized GOx and SWCNT electronic film at the negative potential value (-0.45 V vs. Ag/AgCl). The SWCNT electronic film-based glucose biosensor exhibited a sensitivity of 98 ㎂/mM·cm². In addition, the SWCNT electronic film biosensor showed the excellent selectivity (less than 4 % change) against a variety of redox-active interfering substances, such as ascorbic acid, uric acid, dopamine, and acetaminophen, by avoiding co-oxidation of the interfering substances at the negative potential value.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2009.05a
• /
• pp.31.1-31.1
• /
• 2009

Carbon nanotubes (CNTs) are attractive material because of their superior electrical, mechanical, and chemical properties. Furthermore, their geometric features such as a large aspect ratio and a small radius of curvature at tip make them ideal for low-voltage field emission devices including backlight units of liquid crystal display, lighting lamps, X-ray source, microwave amplifiers, electron microscopes, etc. In field emission devices for display applications, the phosphor anode is positioned against the CNT emitters. In most case, light generated from the phosphor by electron bombardment passes through the anode front plate to reach observers. However, light is produced in a narrow depth of the surface of the phosphor layer because phosphor particles are big as much as several micrometers, which means that it is necessary to transmit through the phosphor layer. Hence, a drop of light intensity is unavoidable during this process. In this study, we fabricated a transparent cathode back plate by depositing an ultra-thin film of single walled CNTs (SWCNTs) on an indium tin oxide (ITO)-coated glass substrate. Two types of phosphor anode plates were employed to our transparent cathode back plate: One is an ITO glass substrate with a phosphor layer and the other is a Cr-coated glass substrate with phosphor layer. For the former case, light was radiated from both the front and the back sides, where luminance on the back was ~30% higher than that on the front in our experiments. For the other case, however, light was emitted only from the cathode back side as the Cr layer on the anode glass rolled as a reflecting mirror, improving the light luminance as much as ~60% compared with that on the front of one. This study seems to be discussed about the morphologies and field emission characteristics of CNT emitters according to the experimental parameters in fabricating the lamps emitting light on the both sides or only on the cathode back side. The experimental procedures are as follows. First, a CNT aqueous solution was prepared by ultrasonically dispersing purified SWCNTs in deionized water with sodium dodecyl sulfate (SDS). A milliliter or even several tens of micro-liters of CNT solution was deposited onto a porous alumina membrane through vacuum filtration. Thereafter, the alumina membrane was solvated with the 3 M NaOH solution and the floating CNT film was easily transferred to an ITO glass substrate. It is required for CNT film to make standing CNTs up to serve as electron emitter through an adhesive roller activation.

• Electrical & Electronic Materials
• /
• v.12 no.7
• /
• pp.7-11
• /
• 1999

Fully sealed field emission display in size of 4.5 inch has been fabricated using single-wall carbon nanotubes-organic vehicle com-posite. The fabricated display were fully scalable at low temperature below 415$^{\circ}C$ and CNTs were vertically aligned using paste squeeze and surface rubbing techniques. The turn-on fields of 1V/${\mu}{\textrm}{m}$ and field emis-sion current of 1.5mA at 3V/${\mu}{\textrm}{m}$ (J=90${\mu}{\textrm}{m}$/$\textrm{cm}^2$)were observed. Brightness of 1800cd/$m^2$ at 3.7V/${\mu}{\textrm}{m}$ was observed on the entire area of 4.5-inch panel from the green phosphor-ITO glass. The fluctuation of the current was found to be about 7% over a 4.5-inch cath-ode area. This reliable result enables us to produce large area full-color flat panel dis-play in the near future. Carbon nanotubes (CNTs) have attracted much attention because of their unique elec-trical properties and their potential applica-tions [1, 2]. Large aspect ratio of CNTs together with high chemical stability. ther-mal conductivity, and high mechanical strength are advantageous for applications to the field emitter [3]. Several results have been reported on the field emissions from multi-walled nanotubes (MWNTs) and single-walled nanotubes (SWNTs) grown from arc discharge [4, 5]. De Heer et al. have reported the field emission from nan-otubes aligned by the suspension-filtering method. This approach is too difficult to be fully adopted in integration process. Recently, there have been efforts to make applications to field emission devices using nanotubes. Saito et al. demonstrated a car-bon nanotube-based lamp, which was oper-ated at high voltage (10KV) [8]. Aproto-type diode structure was tested by the size of 100mm $\times$ 10mm in vacuum chamber [9]. the difficulties arise from the arrangement of vertically aligned nanotubes after the growth. Recently vertically aligned carbon nanotubes have been synthesized using plasma-enhanced chemical vapor deposition(CVD) [6, 7]. Yet, control of a large area synthesis is still not easily accessible with such approaches. Here we report integra-tion processes of fully sealed 4.5-inch CNT-field emission displays (FEDs). Low turn-on voltage with high brightness, and stabili-ty clearly demonstrate the potential applica-bility of carbon nanotubes to full color dis-plays in near future. For flat panel display in a large area, car-bon nanotubes-based field emitters were fabricated by using nanotubes-organic vehi-cles. The purified SWNTs, which were syn-thesized by dc arc discharge, were dispersed in iso propyl alcohol, and then mixed with on organic binder. The paste of well-dis-persed carbon nanotubes was squeezed onto the metal-patterned sodalime glass throuhg the metal mesh of 20${\mu}{\textrm}{m}$ in size and subse-quently heat-treated in order to remove the organic binder. The insulating spacers in thickness of 200${\mu}{\textrm}{m}$ are inserted between the lower and upper glasses. The Y\ulcornerO\ulcornerS:Eu, ZnS:Cu, Al, and ZnS:Ag, Cl, phosphors are electrically deposited on the upper glass for red, green, and blue colors, respectively. The typical sizes of each phosphor are 2~3 micron. The assembled structure was sealed in an atmosphere of highly purified Ar gas by means of a glass frit. The display plate was evacuated down to the pressure level of 1$\times$10\ulcorner Torr. Three non-evaporable getters of Ti-Zr-V-Fe were activated during the final heat-exhausting procedure. Finally, the active area of 4.5-inch panel with fully sealed carbon nanotubes was pro-duced. Emission currents were character-ized by the DC-mode and pulse-modulating mode at the voltage up to 800 volts. The brightness of field emission was measured by the Luminance calorimeter (BM-7, Topcon).

• Advances in nano research
• /
• v.8 no.3
• /
• pp.215-228
• /
• 2020

In this paper, a new method based on the Sander theory is developed for SWCNTs to predict the vibrational behavior of length and ratio of thickness-to-radius according to various end conditions. The motion equation for this system is developed using Rayleigh-Ritz's method. The proposed model shows the vibration frequencies of armchair (5, 5), (7, 7), (9, 9), zigzag (12, 0), (14, 0), (19, 0) and chiral (8, 3), (10, 2), (14, 5) under different support conditions namely; SS-SS, C-F, C-C, and C-SS. The solutions of frequency equations have been given for different boundary condition, which have been given in several graphs. Several parameters of nanotubes with characteristic frequencies are given and vary continuously in length and ratio of thickness-to-radius. It has been illustrated that an enhancing the length of SWCNTs results in decreasing of the frequency range. It was demonstrated by increasing of the height-to-radius ratio of CNTs, the fundamental natural frequency would increase. Moreover, effects of length and ratio of height-to-radius with different boundary conditions have been investigated in detail. It was found that the fundamental frequencies of C-F are always lower than that of other conditions, respectively. In addition, the existence of boundary conditions has a significant impact on the vibration of SWCNTs. To generate the fundamental natural frequencies of SWCNTs, computer software MATLAB engaged. The numerical results are validated with existing open text. Since the percentage of error is negligible, the model has been concluded as valid.

• Smart Structures and Systems
• /
• v.8 no.1
• /
• pp.139-155
• /
• 2011

Polymeric thin-film assemblies whose bulk electrical conductivity and mechanical performance have been enhanced by single-walled carbon nanotubes are proposed for measuring strain and corrosion activity in metallic structural systems. Similar to the dermatological system found in animals, the proposed self-sensing thin-film assembly supports spatial strain and pH sensing via localized changes in electrical conductivity. Specifically, electrical impedance tomography (EIT) is used to create detailed mappings of film conductivity over its complete surface area using electrical measurements taken at the film boundary. While EIT is a powerful means of mapping the sensing skin's spatial response, it requires a data acquisition system capable of taking electrical impedance measurements on a large number of electrodes. A low-cost wireless impedance analyzer is proposed to fully automate EIT data acquisition. The key attribute of the device is a flexible sinusoidal waveform generator capable of generating regulated current signals with frequencies from near-DC to 20 MHz. Furthermore, a multiplexed sensing interface offers 32 addressable channels from which voltage measurements can be made. A wireless interface is included to eliminate the cumbersome wiring often required for data acquisition in a structure. The functionality of the wireless impedance analyzer is illustrated on an experimental setup with the system used for automated acquisition of electrical impedance measurements taken on the boundary of a bio-inspired sensing skin recently proposed for structural health monitoring.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2015.08a
• /
• pp.182.2-182.2
• /
• 2015

최근 학계나 산업계에서 투명 전자 소자에 대하여 활발한 연구가 진행되면서, 투명 전 도성 산화물(TCO: transparent conductive oxide)에 대한 관심이 높아지고 있다. 대표적인 TCO 물질인 Indium Tin Oxide (ITO)는 가시 광 영역에서의 높은 투과 및 높은 도전성을 가져 전압을 인가하면 발열이 가능하므로 이를 투명 면상 발열체에 적용시키는 연구가 활발히 진행되고 있다. 하지만, ITO는 발열 테스트 결과 온도가 상승함에 따라 발열이 일부분에 집중되는 현상이 있으며, 전도성을 높이기 위하여 추가공정이 필요하다. 또한, 글라스의 곡면 부분에서 ITO를 사용하면 유연성이 부족하므로 크랙이 발생한다는 단점이 있다. 따라서, 최근 Silver nanowire (AgNW), Single-walled Carbon nanotube (SWCNT), ITO를 기반으로 한 AgNW에 ITO를 증착 하거나 SWCNT를 코팅하여 우수한 전기적, 광학적 특성을 지닌 하이브리드 전극이 투명 면상 발열체 재료로서 사용되고 있다. 하지만 대체된 재료들도 다양한 문제점을 가지고 있다. 예를 들어 고온에서 발열을 유지하지 못하고 끊어지거나 가시광영역의 투과율이 낮은 점 등이 있다. 이런 다양한 문제점들을 보완 할 수 있는 새로운 투명 면상 발열체에 적용한 연구가 요구되고 있다. 본 연구에서는 GZO/Ag/GZO 하이브리드 구조의 투명 면상 발열체를 제작하여 전기적, 광학적 특성을 비교하고 발열량, 온도 균일 성, 발열 유지 안정도를 확인하였다. 본 연구에서는 $50{\times}50mm$ 크기의 Non-alkali glass (삼성코닝 E2000) 기판 상에 DC마그네트론 스퍼터링 공정을 이용하여 상온에서 GZO, Ag, GZO 박막을 연속적으로 증착 하여 다층구조의 하이브리드형 투명 면상 발열체를 제조하였다. 박막 증착 파워는 DC (Ag) power 50 W, RF (GZO) power 200 W로 하였으며 GZO박막두께는 45 nm로 고정 시키고 Ag박막 두께는 5~20 nm로 변화를 주었다. 증착원은 3인치 GZO 세라믹 타깃 (2.27 wt. % Ga2O3) 과 Ag 금속 타깃 (순도 99.99%)을 사용하였으며, Ar을 40 sccm 주입 후 Working pressure는 고 순도 Ar을 사용하여 1.0 Pa로 고정하며 10분간 Pre-sputtering을하고 증착을 진행하였다. 앞선 실험을 통해 증착한 박막의 전기적, 광학적 특성은 각각 Hall-effect measurements system (ECOPIA, HMS3000), UV-Vis spectrophotometer (UV-1800, Shimadzu)를 사용해 측정 되었으며, 하이브리드 표면의 구조 및 형상은 FESEM으로 관찰하였다. 또한 표면온도 측정기infrared camera (IR camera)를 이용하여 4~12 V/cm의 전압을 인가 시 시간에 따른 투명 면상 발열체의 표면 온도변화를 관찰하였다.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2003.03a
• /
• pp.136-136
• /
• 2003

카본나노튜브는 상용되는 기존의 센서에 비해 표면적이 넓어 감도가 놀고 응답속도가 빠르다. 또한 나노 스케일의 크기를 가지므로 고직접화를 실현할 수 있으며 기능복구성이 뛰어나 상온동작을 통한 저전력화가 가능하다. 본 실험에서는 아크방전법으로 합성한 카본나노튜브를 가스센서로 제작하여 상온에서 NH$_3$, NO 가스와의 반응 특성을 평가하였다. 또한 origin soot와 이를 정제한 purified CNT를 SEM(주사전자현미경), TEM(투과전자현미경), Raman scattering spectroscopy(라만 산란 분광기)를 통해 재료적 특성을 조사하고 이를 가스 감응 곡선과 연관하여 비교, 분석하였다. 전극에 CNT막을 형성시키기 위해 3g의 N,N dimethylformamide 용액에 CNT 10mg을 분산시킨 후 2시간동안 초음파 처리하였다. 이 용액을 mask를 이용해 전극 위에 막을 형성시킨 후 20$0^{\circ}C$에서 열처리하였다. 이렇게 제조된 origin soot와 purified CNT센서는 flow system을 이용하여 측정하였고 $N_2$분위기 하에서 센서를 안정화시킨 후 측정가스와의 반응을 살펴보았다 센서의 반응속도, 회복속도, 감도 등의 측정결과 origin soot는 NH$_3$ 25ppm에서 20%, purified CNT는 1%의 감도를 보여 20배 높은 감도를 보았다. NO 25ppm의 경우에도 origin soot가 8%, purified CNT는 0.8%의 감도를 보여 10배 높은 감도를 보였다. 이는 탄소입자가 많은 origin soot가 purified CNT 보다 표면적이 넓어 보다 많은 가스 흡착 싸이트를 가지기 때문이다. 하지만 origin soot는 반응시간과 회복속도가 Purified CNT 보다 2배 이상 느려 표면적 증가에 따른 가스 흡착과 탈착 능력이 떨어짐을 알 수 있었다. 또한 CNT와 가스사이의 전하 이동 방향에 따라 NH$_3$는 양의 감도를 NO는 음의 감도를 보였다 이는 전하의 이동 방향에 따라 전하와 캐리어 사이의 결합 및 해리가 일어나게 되고 결국 카본나노튜브 내의 캐리어 수를 증감시킴에 따라 나타나는 현상이다. 이러한 가스의 감도는 농도에 따라 증가하였으며 origin soot를 이용하여 1ppm이하의 NH$_3$ 가스를 검출할 수 있었다.

• Composites Research
• /
• v.31 no.6
• /
• pp.371-378
• /
• 2018

In this study, the thermoelastic properties of poly lactic acid (PLA) based nanocomposites are predicted by molecular dynamics (MD) simulation and a micromechanics model. The stereocomplex mixed with L-lactic acid (PLLA) and D-lactic acid (PDLA) is modeled as matrix phase and a single walled carbon nanotube is embedded as reinforcement. The glass transition temperature, elastic moduli and thermal expansion coefficients of pure matrix and nanocomposites unit cells are predicted though ensemble simulations according to the hydrolysis. In micromechanics model, the double inclusion (D-I) model with a perfect interface condition is adopted to predict the properties of nanocomposites at the same composition. It is found that the stereocomplex nanocomposites show prominent improvement in thermal stability and interfacial adsorption regardless of the hydrolysis. Moreover, it is confirmed from the comparison of MD simulation results with those from the D-I model that the interface between CNT and the stereocomplex matrix is slightly weak in nature.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.06a
• /
• pp.311-311
• /
• 2009

Carbon nanotubes (CNTs) belong to an ideal material for field emitters because of their superior electrical, mechanical, and chemical properties together with unique geometric features. Several applications of CNTs to field emitters have been demonstrated in electron emission devices such as field emission display (FED), backlight unit (BLU), X-ray source, etc. In this study, we fabricated a CNT cathode by using filtration processes. First, an aqueous CNT solution was prepared by ultrasonically dispersing purified single-walled CNTs (SWCNTs) in deionized water with sodium dodecyl sulfate (SDS). The aqueous CNT solution in a milliliter or even several tens of micro-litters was filtered by an alumina membrane through the vacuum filtration, and an ultra-thin CNT film was formed onto the alumina membrane. Thereafter, the alumina membrane was solvated by acetone, and the floating CNT film was easily transferred to indium-tin-oxide (ITO) glass substrate in an area defined as 1 cm with a film mask. The CNT film was subjected to an activation process with an adhesive roller, erecting the CNTs up to serve as electron emitters. In order to measure their luminance characteristics, an ITO-coated glass substrate having phosphor was employed as an anode plate. Our field emitter array (FEA) was fairly transparent unlike conventional FEAs, which enabled light to emit not only through the anode frontside but also through the cathode backside, where luminace on the cathode backside was higher than that on the anode frontside. Futhermore, we added a reflecting metal layer to cathode or anode side to enhance the luminance of light passing through the other side. In one case, the metal layer was formed onto the bottom face of the cathode substrate and reflected the light back so that light passed only through the anode substrate. In the other case, the reflecting layer coated on the anode substrate made all light go only through the cathode substrate. Among the two cases, the latter showed higher luminance than the former. This study will discuss the morphologies and field emission characteristics of CNT emitters according to the experimental parameters in fabricating the lamps emitting light on the both sides or only on the either side.