• Proceedings of the KSME Conference
• /
• 2001.06d
• /
• pp.796-801
• /
• 2001

During cold operation period, fuel injection system directly contributes the unburned hydrocarbon formation in spark ignition engines. The relationship between injection parameters and HC emission behavior was investigated through a series of experiments. Spray behavior of port fuel injectors was characterized through a quantitative evaluation of mass concentration of liquid fuel by a patternator and PDA. 6-hole injector was found to produce finer spray than single hole one. Using a purpose-built test rig, the wall wetting fuel was measured, which was mostly affected by wall temperature. Varying coolant temperature($20{\sim}80^{\circ}C$), HC emissions were measured in a production engine. With respect to the different types of injectors, HC emission was also measured. In the 6-hole injector application, the engine produced less HC emission in low coolant temperature region. Though it produces much more amount of wetting fuel, it has the advantages of finer atomization quality. In high coolant temperature region, there was little effect between different types of injectors. The control schemes to reduce HC emissions during cold start could be suggested from the findings that the amount of fuel supply and HC emission could be reduced by utilizing fine spray and high intake wall temperature.

• Journal of Power Electronics
• /
• v.18 no.4
• /
• pp.1015-1026
• /
• 2018

A family of dual-DC-input (DI) dual-buck inverters (DBIs) is proposed by employing a DI switching cell as the input of traditional DBIs. Three power ports, i.e. a low voltage DC input port, a high voltage DC input port and an AC output port, are provided by the proposed DI-DBIs. A low voltage DC source, whose voltage is lower than the peak amplitude of the AC side voltage, can be directly connected to the DI-DBI. This supplies power to the AC side in single-stage power conversion. When compared with traditional DBI-based two-stage DC/AC power systems, the conversion stages are reduced, and the power rating and power losses of the front-end Boost converter of the DI-DBI are reduced. In addition, five voltage-levels are generated with the help of the two DC input ports, which is a benefit in terms of reducing the voltage stresses and switching losses of switches. The topology derivation method, operation principles, modulation strategy and characteristics of the proposed inverter are analyzed in-depth. Experimental results are provided to verify the effectiveness and feasibility of the proposed DI-DBIs.

• Journal of Biomedical Engineering Research
• /
• v.14 no.4
• /
• pp.327-332
• /
• 1993

Automatic transmission of data from the blood analyzer to the request site is one of the most important part in hospital computerization. We have developed a system that transmits data from the arterial blood gas analyzer to the request site automatically In this system HOST computer, FILE server,'LAN(Local Area Network) , 3270 Emulator and bfulti-port card are integrated with 3 blood gas analyzers(NOVA Inc., USA) which are connected to a single multi-port card in a personal computer. When specimen are collected from tramp)inly sites, they are transferee to the laboratory In the Yonsei Cardiovascular Center After analysis, the result is transmitted to the personal computer via serial commnunication between machine and multi-port card using interrupt method. Then, the patient's information (Name, Patient ID No., etc.) is obtained from the HOST computer througth the emulator. The combined data (patient information & lab data) is transmitted to each request site via LAN automatically These results are stored in the File Server for one year and they can be reviewed anytime. Also, it could be used for the various statistics and the flow chart for clinical research. Additionally, we found thal this system reduces the personal labor.

• International Journal of Automotive Technology
• /
• v.7 no.5
• /
• pp.519-526
• /
• 2006

For investigating the effect of fuel stratification on flame propagation, initial flame development and propagation were visualized under different axially stratified states in a port injection SI engine. Stratification was controlled by the combination of the port swirl ratio and injection timing. Experiments were performed in an optical single cylinder engine modified from a production engine and images were captured through the quartz window mounted in the piston by an intensified CCD camera. Firstly in this paper, the characteristics under no port-generated swirl condition, i.e. normal conventional case was studied. Under various stratified conditions, flame images were captured at the pre-set crank angles. These were averaged and processed to characterize the flames propagation. The flame stability was estimated by the weighted average of flame area and luminosity. The stability was also evaluated through the standard deviation of flame area and propagation distance, and mean absolute deviation of propagating direction. Results show that stratification state according to injection timing do not affect on the direction of flame propagation. The flame development and the initial flame stability are strongly dependent on the stratified conditions and the initial flame stability is closely related to the engine stability and lean misfire limit.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.18 no.4
• /
• pp.912-919
• /
• 1994

The engine combustion is one of the most important processes affecting performance and emissions. One effective way to improve the engine combustion is to control the motion of the charge inside a cylinder by means of optimum induction system design, because the flame speed is mainly determined by the turbulence at compression(TDC) process in S.I. engine. It is believed that the tumble and swirl motion generated during intake stroke breaks down into small-scale turbulence in the compression stroke of the cycle. However, the exact nature of this relationship is not well known. This paper describes the tumble flow measurements inside the cylinder of a 4-valve S.I. engine using laser Doppler velocimetry(LDV) under motoring(non-firing) conditions. This is conducted on an optically assesed single cylinder research engine under motored conditions at an engine speed of 1000rpm. Three different cylinder head intake port configurations are studied to develop a better understanding the tumble flow generation, development, and breakdown mechanisms.

• Journal of Navigation and Port Research
• /
• v.38 no.6
• /
• pp.567-575
• /
• 2014

In recent times, an obvious strategy in liner shipping markets that has come to the fore is slow steaming. Nowadays, most liner shipping companies have decelerated the voyage speed to 15-18 knots on major routes, and some leading liner shipping companies have a plan to reduce it to below 15 knots. Slow steaming is helpful in reducing the operating cost and the amount of greenhouse-gas emissions on a single vessel with lower fuel consumption. However, it also creates various negative effects such as the opportunity cost, additional fixed costs and an in-transit inventory cost on a loop. Hence, the net operating cost on a loop is changing dynamically due to the changes of voyage speed based on various slow steaming effects. The aim of this study is to analyze the slow steaming effects in the liner shipping, and to find the best voyage speed that minimizes the operating cost on a loop. Moreover, this study suggests the recommendable strategy for liner shipping companies. To achieve the aim of this study, a simulation model has been designed using System Dynamics.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.26 no.1
• /
• pp.26-33
• /
• 1990

The behavior and mixing process of the forced plume are studied in the hydraulic laboratory. The dilution rate of discharged waste water from the port in various hydraulic condition was analized. The effect of densimetric Froude number and the discharge type on the dilution rate are discussed: In the vertical discharge, the forced plume of small densimetric Froude number mixes more actively than that of the large one. In the horizontal discharge, forced plume of large densimetric Froude number dilutes more rapidly than that of the small one. The mixing takes place more vigorously in the horizontal discharge than in the vertical one. The multi-port diffuser is more effective for the waste water discharge system than the single port diffuser in the tidal swinging coastal sea.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.19 no.5
• /
• pp.29-34
• /
• 2011

This study investigates the potential of DME/Diesel dual fuel engine for reducing emissions with same power. Dual fuel engine controls the combustion using two different fuels, DME and diesel with different auto-ignition timings. In the previous work, the caracteristics of combustion and emissions under single cylinder engine and ignition is done by compression ignition. Pre-mixture is formed by injecting low-pressure DME into an intake manifold and high-pressure fuel (diesel or DME) is injected directly into the cylinder. Both direct diesel injection and port fuel injection reduced the significant amount of Smoke, CO and NOx in the homogeneous charge compression ignition engine due to present of oxygen in DME. In addition, when injecting DME directly in cylinder with port DME injection, there is no changes in emissions and energy consumption rate even operated by homogeneous charge compression ignition.

• Journal of Navigation and Port Research
• /
• v.33 no.5
• /
• pp.331-337
• /
• 2009

Container crane is main equipment in container terminals and it determines the productivity and the efficiency of container terminals. The typical type of container cranes has the single trolley and one among advanced types of them has the dual trolley. The objective of this paper is to analyze the buffer size of a container crane with the dual trolley in container terminals. We present a simulation model for analysing the buffer space of a container crane with the dual trolley. The buffer space is located between main trolley in sea-side and second trolley in yard-side. We performs various simulation experiments and analyze the buffer size to estimate the required productivity.

• Journal of Navigation and Port Research
• /
• v.36 no.7
• /
• pp.553-559
• /
• 2012

It is extremely important to predict the logistics requirements in a scientific and rational way. However, in recent years, the improvement effect on the prediction method is not very significant and the traditional statistical prediction method has the defects of low precision and poor interpretation of the prediction model, which cannot only guarantee the generalization ability of the prediction model theoretically, but also cannot explain the models effectively. Therefore, in combination with the theories of the spatial economics, industrial economics, and neo-classical economics, taking city of Erdos as the research object, the study identifies the leading industry that can produce a large number of cargoes, and further predicts the static logistics generation of the Erdos and hinterlands. By integrating various factors that can affect the regional logistics requirements, this study established a logistics requirements potential model from the aspect of spatial economic principles, and expanded the way of logistics requirements prediction from the single statistical principles to an new area of special and regional economics.