• 전자공학회논문지D
• /
• 제35D권11호
• /
• pp.55-61
• /
• 1998

정공 전달 중합체인 Poly(N-vinylcarbazole) (PVK)와 전자전달 유기물 재료인 2-(4-biphenyl)-5-(t-butyl-phenyl)-1,3,4-oxadiazole (Bu-PBD)에 발광 유기물 색소 Coumurine 6, TPB, Rhodamine B를 각각 도핑한 단층박막 유기물 전기발광 소자를 제작하였다. 스핀 코팅 방법에 의한 단층 구조와 가용성 재료의 사용으로부터 소자제작이 간단하였다. 활성영역은 인듐주석산화물(ITO) 과 알루미늄 전극 사이에 놓인 단층으로 구성하고 있다. 이러한 구조에서 전자와 정공의 전하가 각 전극에서 PVK : Bu-PBD 활성층으로 주입된다. 전압을 인가한 후 발광된 빛의 색은 각각 TPB, C6, Rhodamine B의 유기물 색소에 의해 481nm, 500nm, 585nm 파장을 갖는 푸른색, 초록색 및 오렌지색을 나타내었다. PVK유기물은 다른 발광색을 갖는 유기물 색소를 분자 적으로 도핑 함으로서 주요한 중합체로서 사용될 수 있다. 그리고 전기발광색은 전체 가시광선 파장 내로 조절될 수 있다.

• 한국재료학회지
• /
• 제20권5호
• /
• pp.267-270
• /
• 2010

Sn doped $In_2O_3$ (ITO) and ITO/Cu/ITO (ICI) multilayer films were prepared on glass substrates with a reactive radio frequency (RF) magnetron sputter without intentional substrate heating, and then the influence of the Cu interlayer on the methanol gas sensitivity of the ICI films were considered. Although both ITO and ICI film sensors had the same thickness of 100 nm, the ICI sensors had a sandwich structure of ITO 50 nm/Cu 5 nm/ITO 45 nm. The ICI films showed a ten times higher carrier density than that of the pure ITO films. However, the Cu interlayer may also have caused the decrement of carrier mobility because the interfaces between the ITO and Cu interlayer acted as a barrier to carrier movement. Although the ICI films had two times a lower mobility than that of the pure ITO films, the ICI films had a higher conductivity of $3.6{\cdot}10^{-4}\;{\Omega}cm$ due to a higher carrier density. The changes in the sensitivity of the film sensors caused by methanol gas ranging from 50 to 500 ppm were measured at room temperature. The ICI sensors showed a higher gas sensitivity than that of the ITO single layer sensors. Finally, it can be concluded that the ICI film sensors have the potential to be used as improved methanol gas sensors.

• 한국레이저가공학회지
• /
• 제17권1호
• /
• pp.1-6
• /
• 2014

Indium tin oxide (ITO) is an important transparent conducting oxide (TCO). ITO films have been widely used as transparent electrodes in optoelectronic devices such as organic light-emitting devices (OLED) because of their high electrical conductivity and high transmission in the visible wavelength. Finding ways to control ITO micromachining depth is important role in the fabrication and assembly of display field. This study presented the depth control of ITO patterns on glass substrate using a femtosecond laser and slit. In the proposed approach, a gaussian beam was transformed into a quasi-flat top beam by slit. In addition, pattern of square type shaped by slit were fabricated on the surfaces of ITO films using femtosecond laser pulse irradiation, under 1030nm, single pulse. Using femtosecond laser and slit, we selectively controlled forming depth and removed the ITO thin films with thickness 145nm on glass substrates. In particular, we studied the effect of pulse number on the ablation of ITO. Clean removal of the ITO layer was observed when the 6 pulse number at $2.8TW/cm^2$. Furthermore, the morphologies and fabricated depth were characterized using a optical microscope, atomic force microscope (AFM), and energy dispersive X-ray spectroscopy (EDS).

• 한국재료학회지
• /
• 제15권8호
• /
• pp.543-547
• /
• 2005

Organic electroluminescence devices were made from 1,4-bis-(9-anthrylvinyl)benzene (AVB) and 1,4-bis-(9-aminoanthryl)benzene (AAB) anthracene derivatives. Device structure was ITO/AVB/PANI(EB)/Al (multi-layer device) and ITO/AAB:DCM/Al(single-layer device). In these devices, AVB, polyaniline(emeraldine base) (PANI(EB)) and AAB were used as the emitting material. 4-(dicyanomethylene)-2-methyl-6-p-(dimethylamino)styryl-4H -pyran(DCM) was used as red fluorescent dopant. We studied change of fluorescence wavelength with concentration of DCM doped in AAB. The ionization potential (IP) and optical band gap (Eg) were measured by cyclic voltammetry and UV-visible spectrum. We compared with difference of emitting wavelength between photoluminescence and electroluminescence spectrum. In case of the multi-layer device, PANI and AVB EL spectra have similar wave pattern to each PL spectrum and when PAM and AVB were used at the same time, and multi-layer device showed that a balanced recombination and radiation kom PANI and AVB. In case of the single-layer device, with the increase of DCM concentration, the blue emission decreases and red emission increases. This indicates that DCM was excited by the energy transfer from AAB to DCM or the direct recombination at the dopant sites due to carrier trapping, or both. The device with $1.0wt\%$ DCM concentration gave white light.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1997년도 추계학술대회 논문집
• /
• pp.163-166
• /
• 1997

Electroluminescent(EL) dcvice based on organic thin layers have attracted lots of interests because of thier possible application as large-area light-emitting displays. It was known that MEH-PPV and 1, 1, 4, 4, -Tetraphenyl-1, 3-butadiene(TPB) has red and blue emission peak at 580nm and 480nm, respectively. In this study, MEH-PPV films and TPB films were prepared by spin coating and vacuum deposition method, respectively. Films of MEH-PPV and TPB double layer were also prepared by the same method. Photoluminescent(PL) characteristics of these single and doubler layers were investigated, where a cell structure of glass substrate/ITO/MEH-PPV and/or TPB/Al was employed. It was found that the photoluminescent efficiency of TPB film was higher than that of MEH-PPV film with a single layer and also with a double structure. These films have also different I-V characteristics.

• 한국전기전자재료학회논문지
• /
• 제31권3호
• /
• pp.165-170
• /
• 2018

In this study, double-layered TCO (transparent conductive oxide) films were produced by depositing two distinct TCO materials: $SnO_2$ works as an n-type layer and ITO (indium-doped tin oxide) serves as a transparent conductor. Both transparent conductive oxide-films were sequentially deposited by sputtering. The electrical and optical properties of single-layered TCO films ($SnO_2$) and double-layered TCO ($ITO/SnO_2$) films were investigated. A TCO-embedding photodetector was realized through the formation of an $ITO/SnO_2/p-Si/Al$ layered structure. The remarkably high rectifying ratio of 400.64 was achieved with the double-layered TCO device, compared to 1.72 with the single-layered TCO device. This result was attributed to the enhanced electrical properties of the double-layered TCO device. With respect to the photoresponses, the photocurrent of the double-layered TCO photodetector was significantly improved: 1,500% of that of the single-layered TCO device. This study suggests that, due to the electrical and optical benefits, double-layered TCO films are effective for enhancing the photoresponses of TCO photodetectors. This provides a useful approach for the design of photoelectric devices, including solar cells and photosensors.

• 열처리공학회지
• /
• 제24권2호
• /
• pp.87-91
• /
• 2011

Single layer Sn doped $In_2O_3$ (ITO) films and ITO 50 nm / Au 10 nm / ITO 40 nm (IAI) multilayer films were prepared with electron beam assisted magnetron sputtering on glass substrates. The effects of the Au interlayer, post-deposition atmosphere annealing and intense electron irradiation on the methanol gas sensitivity were investigated at room temperature. As deposited ITO films did not show any diffraction peaks in the XRD pattern, while the IAI films showed the diffraction peak for $In_2O_3$ (400). In this study, the gas sensitivity of ITO and IAI films increased proportionally with the methanol vapor concentration and an intense electron beam irradiated IAI film shows the higher sensitivity than the others film. From the XRD pattern, it is supposed that increased crystallization promotes the gas sensitivity. This approach is promising in gaining improvement in the performance of IAI gas sensors used for the detection of methanol vapor at room temperature.

• 대한화학회지
• /
• 제63권1호
• /
• pp.37-44
• /
• 2019

N,N'-bis(ethyldihydrogen phosphate)-1,4,5,8-naphthalene bis(dicarboximide) (EPNI) and N,N'-bis(ethyldihydrogen phosphate)-3,4,9,10-perylene bis(dicarboximide) (EPPI) and their zirconium bisphosphate multilayers (Zr-EPNI and Zr-EPPI), that had been briefly reported by us, were further investigated in terms of their electrochemical properties. EPNI in aqueous solution showed typical two reversible reductions at ITO electrode but the reductions were strongly dependent on solution pH while EPPI showed only an irreversible reduction. The single and mixed multilayers of Zr-EPNI and Zr-EPPI were well constructed on ITO electrode by the alternate adsorptions of zirconium ion and the bisimides. While Zr-EPNI multilayer on ITO electrode showed single broad reversible reduction with $E_{1/2}=-0.68V$, Zr-EPPI gave two separated reductions at $E_{1/2}=-0.54$ and -0.81 V vs SCE, quite differently from the solution properties. The average layer densities of the multilayers were estimated as $1.5{\times}10^{-10}$ and $2.3{\times}10^{-10}mol/cm^2$ for Zr-EPNI and Zr-EPPI, respectively. Both the monolayers of Zr-EPNI and Zr-EPPI could not completely block the electron transfer between $Fe(CN){_6}^{3-}$ in solution and ITO electrode but 3-5 layers of Zr-EPNI and Zr-EPPI could block it completely and mediated the one-way electron transfer at the potential shifted to their reduction potentials. When the monolayer of zirconium 1,10-decanediylbisphosphonate (Zr-DBP) was used as a sublayer of Zr-EPNI and Zr-EPPI layers, the mediated electron transfer became prominent without any direct electron transfer.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2000년도 하계학술대회 논문집
• /
• pp.308-311
• /
• 2000

The organic electroluminescene (EL) device has gathered much interested because of its potential in materials and simple device fabrication. We fabricated EL device which have a mixed single emitting layer containing N,N'-diphenyl-N,N'-(3-methylphenyl)-1,1'-biphenyl-4,4'-diamine [TPD] and poly(3-hexylthiophene) [P3HT]. The molar ratio between P3HT and TPD chaged with 1:1, 3:1, 5:1, 3:2 and 5:2. EL intensity of ITO/P3HT+TPD/Mg:In devices is enhanced by addition of TPD into P3HT. This can be explained that the energy transfer occurs from TPD to P3HT. Recombination probability increases in emitting layer because that TPD as hole transport material plays a role more injection hole and Mg:In (3.7eV) electrode has low work function make easily electron injection. ITO/P3HT+TPD(5:2)/Mg:In devices emit orange-red light at 28V.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2009년도 제38회 동계학술대회 초록집
• /
• pp.351-351
• /
• 2010

OLED(organic light emitting diode)는 액정디스플레이를 대체할 차세대 평판디스플레이로 많은 주목을 받고 있다. 현재 많이 사용되고 있는 OLED의 기판재료는 Glass기판이지만 차세대 Flexible한 display에서의 적용을 위해서는 가볍고 유연한 plastic을 기판 재료로 사용 할 것으로 보인다. 하지만 plastic이 기판재료로 된 OLED의 가장 큰 단점중의 하나가 수분과 산소에 민감하여 열화를 초래한다는 것이다. 이런 수분침투와 열화 과정으로 인해 OLED의 발광효과가 약해져 OLED의 수명과 직접적으로 연결된다. 하여 외부에서 OLED내부로 유입되는 산소, 수분으로 부터 발광재료와 전극의 산화를 방지하며 외부의 충격으로부터 소자를 보호하기 위한 봉지기술은 반드시 필요하다. 따라서 본 연구에서는, flexible한 OLED에 적용되는 금속 코팅한 막의 적층구조 및 기판의 노출온도에 따른 금속 코팅막의 수분침투 특성에 대해 MOCON의 weight gain test (WGT)를 통해 barrier layer에 대해 평가하고 이에 대한 mechanism을 확립하는데 그 목적이 있다. 금속을 코팅한 막은 OLED의 cathode와 anode 재료로 많이 사용되는 Al과 ITO를 sputter장비를 이용해 single layer와 double-layer의 두 가지 구조로 PET기판에 증착하였다. 증착한 Al막의 두께는 각각 50 nm, 100 nm, 200 nm, 400 nm 등 4가지로 하였다. double-layer의 경우에는 총 두께를 절반씩 기판의 양쪽에 증착하였다. 적층구조에 따른 수분침투 특성 평가 결과로 보면 같은 두께일 때 double-layer는 single layer에 비해서 모든 시편에서 수분의 투습율이 낮음으로써 더 좋은 수분침투의 barrier 특성을 나타내었다. 특히 100 nm이상인 경우 투습율은 예상한 값보다 50%이상 낮게 나타났다.