• Fibers and Polymers
• /
• v.7 no.4
• /
• pp.398-403
• /
• 2006

Dimensional constants (k values) of single jersey fabrics made from $LincLITE^{(R)}$ and conventional yams are calculated under dry, steam, full relaxation treatments. Fabrics were made under different tightness factors such as high, medium and low with different twist factors, twist directions and feeder blending. $LincLITE^{(R)}$ yarns made to get soft and bulkier effects with yam count of 39 tex and conventional yams made into 39 tex and 48 tex yam counts. Various effects on K values are analysed using correlation coefficients. K-values are increased with relaxation progression and have shown some differences between in $LincLITE^{(R)}$ and conventional fabrics, and feeder blended fabrics. Loop shape factor is highly affected by tightness factor, relaxation and feeder blending in $LincLITE^{(R)}$ fabrics, whereas twist factor not significantly effects on loop shape factor in conventional fabrics. Stitch density significantly increases with relaxation in conventional fabrics and no significant effect shows with $LincLITE^{(R)}$ fabrics.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.31 no.2 s.161
• /
• pp.197-205
• /
• 2007

We investigated the effects of washing on the mechanical properties and hand values of spandex/cotton and cotton single jersey fabrics. These knitted fabrics were subjected to 30 laundering cycles with a drum-type washer and were followed by drying at $65^{\circ}C$ with a tumble dryer. The mechanical properties of the cotton knitted fabrics changed greatly during the first washing and then suffered no further change in their properties as the number of washing cycle increased. However, the properties of the spandex/cotton knitted fabrics changed continuously throughout all the washing cycles. The cotton/spandex knitted fabrics showed higher values in tensile and bending properties than did the cotton knitted fabrics, though both kinds of fabrics showed less difference in shearing, surface and compression properties. The spandex/cotton knitted fabrics which had proper density had a higher THV for winter underwear after 30 repeated washings than did the cotton knitted fabrics, and the THVs of both fabrics decreased with the increase in the number of washing cycles.

• Fashion & Textile Research Journal
• /
• v.12 no.5
• /
• pp.676-682
• /
• 2010

Superior hydrophilic properties will allow varieties of polyester(PET) fiber materials, fabrics and industrial materials a broader scope of use. The purpose of this study was to investigate the effect of water-absorbent softener treatment on the end-use properties and the hand of polyester knitted fabrics. Two different fabrics were knitted for the summer ladies' outwear; PET jersey and PET mesh. Variables were softner treatment and stitch type(jersey and mesh). Mechanical properties of the fabric samples were measured by KES-FB system. From these, primary hand values(HV) were evaluated by the conversion equation (KW-403-KTU) and the total hand value(T.H.V.) was calculated according to the KN-304 Summer. Both water-absorbent softner treatment and stitch types affected mechanical properties and hand values of PET fabrics. Mesh were thicker than single jersey stitch. As they became thicker, tensile, shear, and compressional energy increased. It appeared that coefficient of friction of mesh stitch was larger than that of single jersey stitch. The coefficient of friction and the mean deviation of surface roughness were decreased by softener treatment. After softner treatment KOSHI and SHARI of the both PET jersey and PET mesh decreased. However, FUKURAMI values of PET jersey increased and that of PET mesh decreased. The T.H.V. of the treated PET jersey was lower than that of the untreated one, while the T.H.V. of the treated PET mesh was higher than that of the untreated one. Overall T.H.V. of the single jersey was better than that of the mesh before and after softner treatment.

• Fashion & Textile Research Journal
• /
• v.5 no.3
• /
• pp.273-282
• /
• 2003

Effect of fixation methods and relaxation treatment on the flame retardant(FR) and physical properties of MDPP/HMM treated cotton weft-knitted fabrics were studied. Combination of four different fixation methods - relaxation, swelling agent treatment, pad dry cure fixation, and wet fixation - were applied to flame retardant finish of cotton weft-knitted fabric with MDPP/HMM. As the results, 1. Swelling agent and wet fixation method helps FR agent penetrate the fiber efficiently. Interlock showed relatively higher values of LOI than single jersey. 2. Interlock showed relatively higher values of bending rigidity(B), shear rigidity(G) and coefficient of friction(MIU) than those of single jersey before and after flame resistant treatment. 3. An increase in internal volume of cotton fiber by relaxation treatment increased the bending rigidity(B), shear rigidity(G) and compressional energy(WC). 4. The cotton weft-knitted fabric treated wet fixation, which crossliked FR agent efficiently, showed higher bending rigidity, shear rigidity(G) and lower compressional energy(WC). Retention of swelling ability of cotton weft-knitted fabrics treated with MDPP/HMM, which increased the internal volume of cotton weft-knitted fabric, showed lower bending rigidity.

• Elastomers and Composites
• /
• v.54 no.2
• /
• pp.91-96
• /
• 2019

The purpose of this study was to examine the effect of different yarn twisting methods on physical properties. Plain single jersey structured fabrics were knitted from Kevlar yarn, and from Kevlar/HPPE, and from Kevlar/Basalt fiber, and from Kevlar/Glass fiber and Kevlar/Stainless steel fiber blended and core-spun yarns. and then, The fabrics were coated NBR Latex. The physical properties, including tear strength, modulus, degree of penetration, heat resistance, and cut resistance of the knitted fabrics were investigated and compared. Kevlar/HPPE blended yarn fabrics recorded the highest heat resistance (13 Sec.). and Kevlar/HPPE blended yarn fabrics had good cut resistance (Cut Level 4).

• Fibers and Polymers
• /
• v.7 no.3
• /
• pp.295-304
• /
• 2006

High-bulk worsted yams with different shrinkable and non-shrinkable acrylic fibers blend ratios are produced and then single jersey weft knitted fabrics with three different structures and loop lengths are constructed. The physical properties of produced yams and compression properties of produced fabrics at eight pressure values (50, 100, 200, 500, 1000, 1500 and $2000 g/cm^2$) were measured using a conventional fabric thickness tester. Then, weft-knitted fabric compression behavior was analyzed using a two parameters model. It is found that at 40 % shrinkable fibre blending ratio the maximum yam bulk, shrinkage, abrasion resistance and minimum yarn strength are obtained. It is also shown that high-bulk acrylic yarn has the highest elongation at 20 % shrinkable fibre blend ratio. The statistical regression analysis revealed that the compression behavior of acrylic weft-knitted fabrics is highly closed to two parameter model proposed for woven fabrics. It is also shown that for weft-knitted structure, there is an incompressible layer (V') which resists against high compression load. Acrylic weft-knitted fabrics with knit-tuck structure exhibit higher compression rigidity and lower softness than the plain and knit-miss structures. In addition, at 20 % shrinkable fibre blend ratio, the high-bulk acrylic weft-knitted fabrics are highly compressible.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.29 no.9_10 s.146
• /
• pp.1274-1284
• /
• 2005

Effect of fixation methods and relaxation treatment on the dimensional stability and physical properties of MDPPA/HMM treated cotton knitted fabrics were studied. Combination of four different fixation methods - relaxation, swelling agent treatment, pad dry cure fixation, and wet fixation - were applied to flame retardant finish of 4 kinds of cotton knitted fabric with MDPPA/HMM. Then these fabrics were washed 10 times. As a result, In swelling treatment on 10G showed relatively higher value of length shrinkage than 14G. Length and width shrinkage were increased by initial washing treatment and no further change was shown after 6 washing cycles. After 10 washing cycles, length and width shrinkage decreased. The KES standardized basic value of B/W, 2HB/W and bursting strength of interlock were relatively larger than those of single jersey. The values of B/W and 2HB/W of cotton knitted fabrics were increased by relaxation and washing treatment but were decreased by swelling treatment. In addition, the bursting strength of the cotton knitted fabrics was decreased after fusing, washing and relaxation treatment.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.45 no.1
• /
• pp.46-55
• /
• 2021

Seam puckering and the seam strength of conductive threads used to produce smart clothing were analyzed according to stitching methods and fabrics. Samples were prepared in a lock stitch and zigzag stitch on plain woven and jersey knit fabric, using one type of polyester sewing thread and three types of commercial conductive threads that consisted of two types of stainless-steel conductive threads (TST and MST) and one type of silver conductive thread (SSV). Seam pucker percentages, shapes, and seam strength were measured. On plain woven fabric as well as jersey knit fabric, three-ply TST and MST showed a higher SP percentage compared to a polyester sewing thread. Meanwhile, single-ply SSV showed the lowest SP percentage. In addition, the SP percentage of the zigzag stitch decreased along the weft and course directions of the fabric, and decreased significantly as the number of fabric layers increased. Moreover, there was a marked tendency for a higher SP percentage in jersey knit fabric compared to plain woven fabric, and the two-dimensional cross-section waveforms of stitches obtained using three-dimensional data that showed increased irregular waveforms and peaks in the zigzag stitch. There were no correlations between seam strength and tensile strength.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.20 no.1
• /
• pp.228-238
• /
• 1996

The purpose of this study was to evaluate the effect of chacteristics of knit fabrics on the microclimate of the skin simulating system. To determine the effect of characteristics of knit fabrics, vapor state of sweat pulse was simulated in the closed system. Different contents of fibers such as cotton, wool and polyester with different yarn size and knit types were chosen for specimens. The changes of humidity and temperature of air layer in the simulated systems were measured. Buffering indices, $K_d$ and $\beta_r$, were determined by considering $\alpha_p, \DeltaP_{max}, t_{max}, and tan\beta$. Physical properties of knit fabrics such as thickness, porosity, air resistance and moisture vapor transport were measured. Results showed that vapor pressure of wool was lower than cotton or polyester This was attributed to the hydrophilicity of wool which absorbed moisture rather quickly and retained in the knit fabric. The time to decrease vapor pressure was faster for polyester than cotton or wool. As a result, $K_d$ was in the order of wool> polye, item> cotton. $\beta_r$ of wool was rower than cotton or polyester due to its lowers porosity and slower desorption rate. For the yarn size, $K_d$ was in the order of 80's> 60's> 30's; thinner and lighter yarn showed better water vapor transport property. For knit type, buffering capacity of single jersey was better than interlock knit fabric. Statistical analysis showed that the air permeability was the most influential factor far the water vapor transport properties.

• Proceedings of the Korean Society for Emotion and Sensibility Conference
• /
• 2008.10a
• /
• pp.118-121
• /
• 2008

The purpose of this study was to evaluate the wearing sensation of T-shirts made with silver combination yarns. The four different single jersey fabrics were knitted to make long sleeve T-shirts: cotton(C), cotton/silver(CS), polyester(P), and polyester/silver(PS). The four kinds of T-shirts were evaluated by six healthy male subjects in a climatic chamber($25^{\circ}C$, 65%RH, 0.5m/sec). The results were as follows. Thermal and fatigue sensation of wearing CS was best. It was found that overall subjective sensation was improved by using silver yarn with cotton for health knitwear.