• 대한치과보철학회지
• /
• 제43권1호
• /
• pp.52-60
• /
• 2005

Purpose. The intent of this study was to evaluate the effects of curing conditions on self-curing denture base resins to find out proper condition in self-curing resin polymerization. Materials and methods, In this study, 3 commercial self-curing denture base resins are used Vertex SC, Tokuso Rebase and Jet Denture Repair Acrylic. After mixing the self curing resin, it was placed in a stainless steel mold(3$\times$6$\times$60mm). The mold containing the resin was placed under the following conditions: in air at 23$^{\circ}C$; or in water at 23$^{\circ}C$; or in water at 23$^{\circ}C$ under pressure(20psi); or in water at 37$^{\circ}C$ under pressure(20psi) or in water at 50$^{\circ}C$ under pressure(20psi) , or in water at 65$^{\circ}C$ under pressure(20psi), respectively. Also heat-curing denture base resin is polymerized according to manufactures' instructions as control. Fracture toughness was measured by a single edge notched beam(SENB) method. Notch about 3mm deep was carved at the center of the long axis of the specimen using a dental diamond disk driven by a dental micro engine. The flexural test was carried out at a crosshead speed 0.5mm/min and fracture surface were observed under measuring microscope. Results and conclusion . The results obtained were summarized as follows : 1. The fracture toughness value of self-curing denture base resins were relatively lower than that of heat-curing denture base resin. 2. In Vertex SC and Jet Denture Repair Acrylic, higher fracture toughness value was observed in the curing environment with pressure but in Tokuso Rebase, low fracture toughness value was observed but there was no statistical difference. 3. Higher fracture toughness value was observed in the curing environment with water than air but there was no statistical difference. 4. Raising the temperature in water showed the increase of fracture toughness.

• Maxillofacial Plastic and Reconstructive Surgery
• /
• 제27권6호
• /
• pp.575-580
• /
• 2005

Transitional implants were developed to support provisional restorations and to allow for load-free osseointegration of conventional implants while a patient was provided with immediate esthetics and function and are usually placed simultaneously at the time of definitive implant placement. Transitional implants are placed in a non-submerged fashion in a single-stage surgery and are designed to be immediately loaded. They generally are made of commercially pure titanium or titanium alloy and are designed as 1-piece implants composed of root and crown replacement segments. Transitional implants can be used in a wide range of indications, such as basic use as temporary implant, to support and protect the primary implants during the healing phase, single crown in the edentulous anterior region of mandibular, anchorage for orthodontic treatment, support a surgical and radiographic template, and primary implant to extremely atrophied alveolar crests of the mandible and maxilla. This article describes the clinical use of transitional implants to support the provisional complete denture and single crown in the restricted edenturous central incisor region of mandible.

• 대한치과기공학회지
• /
• 제8권1호
• /
• pp.85-90
• /
• 1986

The effect of splinting on aqbutment tooth distal movement was performed in vitro study. An acrylic resin mandibular model with missing 2nd premolars, molars and a removable partial denture framework were constructed. The roots of the canines, 1st premolars and edentulous ridges were coated with silicone rubber. A modified Ney Surveyor was used for vertical load appkication, and abutment tooth distal movement were measured with a dial gauge with four conditions of splinting methods were tested by applying unilateral vertical loadings. The results are follows; 1. The magnitude of abutment tooth distal movement on the non-load side was less 40$\sim$69% than that occurred on the load side. 2. On the load side, reducing effect of splinting on abutment tooth movement in the condition of load side double abutment(30%), non-load side double abutment(10%), double abutments of both sides(40%) was compared with single abutments of both sides. 3. On the non-load side, reducing effect of splinting on abutment tooth movement in the condition of load side double abutment(5%), non-load side double abutment(22%), double abutments of both sides(59%) was compared with single abutments of both sides. 4. The magnitude of abutment tooth distal movement in the condition of double abutments of both sides was less 40$\sim$59% than that in the condition of single abutments of both sides.

• 대한치과보철학회지
• /
• 제51권2호
• /
• pp.113-118
• /
• 2013

다수 잔존치를 상실한 경우 잔존치간의 관계가 역학적으로 불리한 상황에 놓일 수 있다. 환자가 의치에 관한 거부감이 없을 때, 이러한 경우 피개의치를 고려할 수 있지만, 무치악 부위에 임플란트를 이용함으로써 역학적인 불리함을 극복하고 국소의치의 지지, 안정, 유지를 향상시킬 수 있다. 본 증례는 소수 잔존치간에 엇갈린 교합을 보이는 환자로 상악 치아에 대합되는 하악의 무치악 부위에 단일 임플란트를 식립하고 $Locator^{(R)}$ attachment를 연결하여 상하악 국소의치로 치료하였다. 기존의 기울어진 교합평면을 이상적으로 재설정하여 환자의 심미적 만족도를 향상시켰다. 치료 이후 6개월간의 임상 관찰에서 환자는 심미적, 기능적으로 만족하고 안정적으로 유지되었기에 보고하고자 한다.

• 대한치과보철학회지
• /
• 제30권4호
• /
• pp.575-581
• /
• 1992

It is a very important procedure to establish the occlusal plane in the construction of complete denture. So many methods have been utilized to establish the occlusal plane in complete denture prosthodontics. However, no single method seems to fully accepted. This study was aimed to review the literature on establishing the occlusal plane in complete denture prosthodontics, to measure the distance from the lower border of the upper lip to the upper incisal edge and to investigate the correlation between the ala-tragus line and the occlusal plane. The results ware as follows ; 1. The average distance between the lower border of the upper lip and the upper incisal edge was $1.45{\pm}1.28mm$. 2. The distance between the lower border of the upper lip and the upper incisal edge had a tendency to decrease with age. 3. A angle of the ala-tragus line to the occlusal plane measured with Fox plane was $-1.41{\pm}2.33^{\circ}$. 4. The ala-tragus line to occlusal plane was nearly parallel, cosidering curve of spee in the upper natural teeth.

• 대한치과보철학회지
• /
• 제41권1호
• /
• pp.81-88
• /
• 2003

Resin-bonded bridge has been an alternative to conventional bridge, since resin-bonded bridge has many attractive advantages such as minimal tooth preparation, short chair time and low cost over conventional bridge. Unfortunately, however, it was reported that resin-bonded bridge showed high failure rate from debonding of retainer in spite of consecutive advances in preparation and materials. And it was shown that multiple abutments were more likely to fail. The majority of debonding failure was considered due to the mobility of the abutment during function. In this view, recently, modification in resin-bonded bridge design was tried. Single retainer, single pontic. 2-unit cantilevered resin-bonded bridge was applied to clinical performance and was shown as retentive or more retentive than fixed-fixed type resin-bonded bridge. This was consistent with the results of studies in 2-unit cantilevered resin-bonded bridges made with all ceramic, In-ceram. The purpose of this article was to overview principles of design and to analyze clinical results of 2-unit cantilevered resin-bonded bridge in comparison with the reports of fixed-fixed resin-bonded bridge.

• 대한치과기공학회지
• /
• 제33권3호
• /
• pp.237-246
• /
• 2011

Purpose: This study investigates dental health and chewing ability of patients hospitalized in geriatric hospital, and compares the chewing ability for each factor that can be used as data for dental healthcare of senior citizens and basic data for denture insurance for the elderly. Methods: The 101 subjects of this study were selected from 178 patients hospitalized in a geriatric hospital located in Daegu Metropolitan City, excluding 77 patients who were being treated in the intensive care unit and who were unable to communicate. The chewing ability of the patients were measured using an evaluation scale based on foods consisting of 10 different hardnesses. Results: Patients with less than 21 teeth, those with dentures and patients who were less than satisfied with their dental conditions had difficulties in chewing hard food such as dried squid and radish kimchi, and the Chewing ability increased proportionally to the number of remaining teeth(p<0.001), appropriateness of the maxillary and mandibular dentures(p<0.005) and the level of dental satisfaction(p<0.001). Conclusion: This study is limited as the subjects were selected from a single hospital and the authors estimate that various studies will be necessary to investigate the Chewing ability of patients hospitalized in long-term hospitals. The subjects of this study did not receive any dental treatment while staying in the hospital and many of the subjects had bad fit denture or didn't have dentures or did not use dentures, although they have dentures, which calls for denture construction and prosthetics through dental treatment.

• 대한치과보철학회지
• /
• 제62권2호
• /
• pp.146-156
• /
• 2024

임플란트 보조 국소의치의 치료는 오래전부터 여러 형태로 시도되어 왔으며, 이 중 임플란트 서베이드 크라운 국소의치의 경우 점차 예지성을 얻고 있으며, 특히 경제적, 해부학적으로 불리한 부분 무치악 환자에게 한 가지 치료 방법이 될 수 있다. 이때 임플란트의 식립 위치는 치료 목적에 따라 전방 식립과 후방 식립으로 분류될 수 있는데, 이는 환자의 치조제, 잔존치 예후, 대합치 등 여러 상황을 고려하여 결정되어야 한다. 본 증례에서는 하악 Kennedy 1급 부분 무치악 환자에게 두 개의 임플란트 서베이드 크라운을 활용한 하악 임플란트 보조 국소의치를 통해 수복하였다. 본 환자에게 후방 식립이 어렵다는 점과 잔존치의 예후를 고려하여 임플란트를 잔존치에 근접한 부위에 두 개를 식립하는 것이 계획되었으며, 가이드 수술을 통해 계획한 위치, 각도, 깊이에 식립되었다. 고정성 보철물 제작 과정은 상악 무치악 치아 배열 과정과 병행하여 예지성을 높였고, 국소의치를 제작 시에는 임플란트가 최후방 지대치로서 과도한 하중이 가하지 않도록 기능 운동을 허용하는 형태로 디자인되고, 이차 인상 과정을 거쳐 제작되었다. 각 치료 과정을 계획한대로 진행하여 환자와 술자 모두 심미적, 기능적으로 만족스러운 결과를 얻었기에 이를 보고하는 바이다.

• 대한치과보철학회지
• /
• 제40권5호
• /
• pp.429-440
• /
• 2002

Current dental restorations present a relatively weak resistance to fracture. Owing to their unique mechanical properties, fibre-reinforced polymers are now being considered. Unidirectional or woven continuous fibres, made of glass, polyethylene, carbon or Kevlar, have been evaluated. This study focused on the use of glass fibre knitted fabrics to reinforce acrylate resins, in order to investigate the possibility to construct single crowns as well as three unit bridges. Some points affecting the final composite system were tested ; 1) static strength, with focus on the stress transfer under a occlusal contact point ; 2) modelling of a three nit bridge ; 3) fatigue strength as a posterior three unit bridge material. The study demonstrated that knitted fabric reinforcements are showing an interesting compromise between stiffness, static strength for single crown. For three unit bridge applications in the posterior arch, however knitted glass fabric reinforcements were not strong enough in fatigue An additional reinforcement in the posterior arch fixed partial denture design was recommended.

• 대한치과기공학회지
• /
• 제39권1호
• /
• pp.35-42
• /
• 2017

Purpose: The purpose of this paper was to evaluate the occurrence of errors regarding adaptation by conducting a three-dimensional assessment comparing the bridge type dental restoration after the cutting process, which has multiple abutments, with a single type dental restoration. Methods: By using ten identical files obtained by scanning the master model, thirty designs were created consisting of ten maxillary right first premolars and ten maxillary right first molars with single crown abutments, along with ten bridge designs with the identical abutment. A 5-axis milling machine was used to produce the design file. The produced denture prostheses were scanned using a silicone replica for a STL file. An evaluation was conducted using 3D analysis software on the master model and each of the thirty data files. Results: The RMS value of the pre-molar (14) was $38.4{\pm}4{\mu}m$ for single and $54.7{\pm}6{\mu}m$ for bridge abutment; therefore, a statistically significant difference was observed for single and bridge designs although both shared the same abutment form (P<.05). Also, the RMS value of the molar (16) was $47.6{\pm}2{\mu}m$ and $56.6{\pm}5{\mu}m$ for the single and bridge designs, respectively, thereby presenting a statistically significant difference (P<.05). Conclusion: As a result, dental prosthesis fabricated using the single method presented better internal adaptation outcomes.