• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.21 no.2
• /
• pp.383-393
• /
• 1996

This paper considers the evaluation of the ecquistion performance for an accesschannel preamble based on a random access procedure of direct sequence code division multiple access(DS/CDMA) reverse link. The parallel acquistion technique that employs the single-well detection scheme and the multiple-dwell(double-dwell) detection scheme is mentioned. The acquisition performance for two detection schemes is compared in therms of the acquisition probability and the acquisition time. The parallel acquisition is done by a bank of N parallel I/Q noncoherent correlators. Expressions on the detection, false alarm, and miss probabilities of the single-dwell and multiple-dwell(double-well) detection schemes are derived for multiple H$_{1}$ cells and multipath Rayleight fading channel. comparing the single-dwell detection scheme with the multiple-dwell(double-dwell) detection scheme in the case of employing the parallel acquisition technique in the reverse link,the numerical results show that the single-dwell detection scheme deomonstrates a better performance.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.49 no.1
• /
• pp.1-6
• /
• 2004

N fertilizer required by rice could be reduced greatly in the rice-barley double cropping system than in the rice single cropping system. This study was conducted to investigate how much of the N fertilizer during the early stage of rice in the rice-barley double cropping system, could be saved compared to that in the rice single cropping system. This experiment was carried out at the paddy field of the National Crop Experiment Station in Suwon, Korea during three years from 1999 to 2001. Amounts of soil mineral nitrogen (SMN) and SPAD values of rice leaf during rice growing season in the rice-barley double cropping system were higher than those in the rice single cropping system under the same amount of N application during two years. Yield and N uptakes of rice at harvesting time were also higher in the rice-barley double cropping system than in the rice single cropping system during two years. Yield and N uptake of rice in the rice single cropping system were decreased when basal N fertilizer was omitted, but those reductions were not found by either omitting basal N fertilizer or omitting N fertilizer at tillering stage in the rice-barley double cropping system during 2000 and 2001. But yield and N uptakes of rice were decreased by 70 kg/10a and 2kgN/10a by the omission of both N application at basal and tillering stages in the rice-barley double cropping system in 2002. It was concluded that N fertilizer as much as tillering N fertilizer could be saved in the rice-barley double cropping system.

• Clinics in Shoulder and Elbow
• /
• v.9 no.1
• /
• pp.89-95
• /
• 2006

Purpose: Arthroscopic repair of rotator cuff tears are many techniques that have been developed to improve the initial postoperative strength of the repair. There was a doubt that current arthroscopic cuff repairs using a single row of suture anchors reproduce insufficient area of the anatomic cuff insertion, and concerns about failure of fixation often lead surgeons to limit early motion. Newer technique of double-row repair in arthroscopic treatment may provide initial stronger fixation and more contact with bone at the repair site than single-row repair did. We studied the comparison between clinical outcomes of arthroscopic single- and double-row repair in cuff tears at 1year postoperatively. Materials and methods: We retrospectively analyzed 40 shoulders with single-row repair and 38 shoulders with double-row repair of full-thickness rotator cuff tears between May 2002 and October 2004. Out of total 78 shoulders, 42 (54%) were male patients and 36 (46%) were female patients and the mean age at surgery was 56 years. All patients were diagnosed by physical examination and MRI. At 1year' follow-up after operation, we evaluated with the ASES and the Constant scoring system, and measured muscle power of abduction, internal and external rotation of the affected shoulder then compared with each other. Results: Mean ASES scores and Constant scores in double-row repair group improved more than single-row repair group significantly at 1year postoperatively. Muscle power of abduction and internal rotation, especially abduction power, improved more significantly in double-row repair group than in single-row repair. Conclusion: Arthroscopic double-row repair for the full thickness rotator cuff tear may be a superior technique, which showed better clinical outcomes and restoration of muscle power compared with single-row repair at relatively short period of postoperative follow-up. Restoration of footprint close to normal anatomy by double-row repair seems to play an important role in the recovery of muscle strength.

• Journal of the Korean Society for Precision Engineering
• /
• v.30 no.8
• /
• pp.785-789
• /
• 2013

Worm gear sets may be either single- or double-enveloping. In a single-enveloping set, the worm wheel is cut into a concave surface, thus partially enclosing the worm when meshed. The double-enveloping worm gear is similar to the single-enveloping gear; however, the worm envelopes the worm gear. Thus both are throated. The double-enveloping worm gear has more of the tooth surface in contact than the single-enveloping worm gear. The larger contact area increases the load-carrying capacity. For this reason, double-enveloping worm gearing is widely applied in heavy-duty machinery, for applications including construction and metallurgy. In this paper, we designed a compact reduction gear that is highly efficient using double-enveloping worm gears. We calculated the bearing load in the worm gearing to select the bearing and the housing surface area according to the recommended values from AGMA(American Gear Manufacturers Association). The finite element method was used to assess the structural integrity.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.4 no.5
• /
• pp.1143-1150
• /
• 2000

A dual-mode multiplier (DMM) that performs single- and double-precision multiplications has been designed using a $0.25-\mum$ 5-metal CMOS technology. An algorithm for efficiently implementing double-precision multiplication with a single-precision multiplier was proposed, which is based on partitioning double-precision multiplication into four single-precision sub-multiplications and computing them with sequential accumulations. When compared with conventional double-precision multipliers, our approach reduces the hardware complexity by about one third resulting in small silicon area and low-power dissipation at the expense of increased latency and throughput cycles. The DMM consists of a $28-b\times28-b$ single-precision multiplier designed using radix-4 Booth receding and redundant binary (RB) arithmetic, an accumulator and a simple control logic for mode selection. It contains about 25,000 transistors on the area of about $0.77\times0.40-m^2$. The HSPICE simulation results show that the DMM core can safely operate with 200-MHZ clock at 2.5-V, and its estimated power dissipation is about 130-㎽ at double-precision mode.

• PNF and Movement
• /
• v.11 no.2
• /
• pp.95-102
• /
• 2013

Purpose : The purpose of this study was to investigate a plantar pressure distribution and the trajectory of the center of pressure on double limb support and single limb support according to level surface, air cushion, and aero step. Methods : 21 healthy adults participated in this study. The plantar pressure were assessed at three different surface conditions(on the level surface, air cushion, and aero step) on double limb support and single limb support. Testing orders were selected randomly. Results : Plantar pressure distribution show a significant difference contact area 1 and contact area 3 on double limb support and single limb support. The trajectory of the center of pressure show an significant difference anteroposterior(AP), mediolateral(ML), and total displacement on double limb support and single limb support. Conclusion : Through the use of soft surface as air cushion and aero step will be using the ankle strategy. This will be to strengthen the muscles around the ankle. Consequently, should help to improve stability and coordination.

• Korean Journal of Applied Biomechanics
• /
• v.29 no.4
• /
• pp.255-261
• /
• 2019

Objective: The purpose of this study was to investigate differences of shock attenuation strategies between double-leg and single-leg landing on sagittal plane using statistical parametric mapping. Method: Nine healthy female professional soccer players (age: 24.0±2.5 yrs, height: 164.9±3.3 cm, weight: 55.7±6.6 kg, career: 11.2±1.4 yrs) were participated in this study. The subjects performed 10 times of double-leg and single-leg landing from the box of 30 cm height onto force plates respectively. The ground reaction force, angle, moment, angular velocity, and power of the ankle, knee, and hip joint on sagittal plane was calculated from initial contact to maximum knee flexion during landing phase. Statistical parametric mapping was used to compare the biomechanical variables of double-leg and single-leg landing of the dominant leg throughout the landing phase. Each mean difference of variables was analyzed using a paired t-test and alpha level was set to 0.05. Results: For the biomechanical variables, significantly increased vertical ground reaction force, plantarflexion moment of the ankle joint, negative ankle joint power and extension moment of the hip joint were found in single-leg landing compared to double-leg landing (p<.05). In addition, the flexion angle and angular velocity of the knee and hip joint in double-leg landing were observed significantly greater than single-leg landing, respectively (p<.05). Conclusion: These findings suggested that negative joint power and plantarflexion moment of the ankle joint can contribute to shock absorption during single-leg landing and may be the factors for preventing the musculoskeletal injuries of the lower extremity by an external force.

• Korean Journal of Optics and Photonics
• /
• v.13 no.3
• /
• pp.258-265
• /
• 2002

In this paper, we design single and symmetrical double lenses with DOE. The specifications are the following : Image area is 4.8 mm $\times$ 3.6 mm, F/# is 2.8 and the overall length (from first lens surface to image plane) is 6.8mm. After comparing the optical performance and characteristic values, we determine that symmetrical double lenses are superior to single lenses. Symmetrical double lenses have the merits of fewer zones, weaker flare, and smaller distortion than single lenses.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.9 no.3
• /
• pp.136-147
• /
• 2009

In this paper we analyze the influence of source/drain (S/D) extension region design for minimizing short channel effects (SCEs) in 25 nm gate length single and double gate Silicon-on-Insulator (SOI) and Germanium-on-Insulator (GOI) MOSFETs. A design methodology, by evaluatingm the ratio of the effective channel length to the natural length for the different devices (single or double gate FETs) and technology (SOI or GOI), is proposed to minimize short channel effects (SCEs). The optimization of non-overlapped gate-source/drain i.e. underlap channel architecture is extremely useful to limit the degradation in SCEs caused by the high permittivity channel materials like Germanium as compared to that exhibited in Silicon based devices. Subthreshold slope and Drain Induced Barrier Lowering results show that steeper S/D gradients along with wider spacer regions are needed to suppress SCEs in GOI single/double gate devices as compared to Silicon based MOSFETs. A design criterion is developed to evaluate the minimum spacer width associated with underlap channel design to limit SCEs in SOI/GOI MOSFETs.

• Journal of Drive and Control
• /
• v.14 no.4
• /
• pp.9-16
• /
• 2017

In this study, the force tracking performance of the single-rod and double-rod type EHAs (Electro-Hydrostatic Actuators) was compared by computer simulation and experiments. The force-controlled EHAs exhibit non-linear behavior that are significantly dependent on operation conditions. The investigation focused on localizing the parameters that provide significant rise to the non-linearity. For this, the single-rod and double-rod type EHAs were mathematically expressed to derive their linear models. In parallel, they were modeled by a commercial simulation program including non-linear properties based on experimental results. It was shown that the dependency of the bulk modulus of oil with entrapped air on working pressure dominated the non-linearity in force control performance in case of the double-rod type EHA. The force control of the single-rod type EHA was influenced by much more elements. Besides the asymmetrical piston geometry and the non-linear bulk modulus of oil, its pilot-operated check valves made it dependent not only on the magnitude of reference input but also on its direction.