• Journal of the Korean Society for Precision Engineering
• /
• v.23 no.6 s.183
• /
• pp.104-110
• /
• 2006

A design and control of electrostatic suspension system for flexible objects is presented. A number of electrode pairs of which the number depends on the object flexibility are positioned above the object and the voltages applied to each electrode pair are controlled, independently on the others, on the basis of the gap length. To implement the system with low cost and compactness, switched-voltage control scheme that is based on the relay feedback control is utilized. Relay feedback control method deploys only a single high-voltage power supply that can deliver a DC voltage of positive and/or negative polarity and thus high voltage amplifiers that are costly and bulky are not needed any more. It is shown that despite the inherent limit cycle property of the relay feedback based control, an excellent performance in vibration suppression is attained due to the presence of a relatively large squeeze film damping originating from the electrodes and levitated object. Employing fourteen electrode pairs, a thin aluminum plate with a thickness of 0.1 mm has been suspended at a gap length of 0.75mm.

• Journal of The Korean Society of Agricultural Engineers
• /
• v.53 no.6
• /
• pp.145-152
• /
• 2011

In order to heat greenhouse nearby river channel, riverbank filtration water source heat pump was developed for getting plenty of heat flux from geothermal energy. Recharging well, thermal storage tank with separating insulation plate and filtering tank for eliminating iron, manganese were mainly developed for making the coefficient of performance (COP) of heat pump higher. Heating system using riverbank filtration water source heat pump was installed at a paprika greenhouse in the Jinju region where a single fold of vinyl cover and 2 layers of horizontal thermal curtain were installed as a part of temperature keeping and heat insulation with a greenhouse area of 3,185 $m^2$. 320,000 kcal/h was supplied for performing a site application tests. A greenhouse heating test was performed from Feb. 1, 2011 to Apr. 30, 2011. As the result of that, COPh of the heat pump was measured in the range of 4.0~4.5, while COPS of the system was represented as 2.9~3.3. COP measured of the heat pump was very good and well responded to indoor heating temperature of the environment control system of a greenhouse.

• BMB Reports
• /
• v.35 no.2
• /
• pp.236-238
• /
• 2002

Based on the zymography analysis, Bacillus sp. DJ-4 (screened from Doen-Jang, a Korean traditional fermented food) secretes seven extracellular fibrinolytic enzymes (EFEs; 68, 64, 55, 45, 33, 27, and 13 kDa) in culture broth. These seven EFEs were analyzed by newly applied SDS-fibrin zymography combined with gradient polyacrylamide (SDS-FZGP). This improved gel system was used with a 5-20% acrylamide gradient in a fibrin zymogram gel for the separation of proteins with molecular masses from below 10kDa to over 100kDa on one gel plate. Using this system, high molecular weight bands (HMWBs) were clearly and sharply resolved. We also examined the relationship between an acrylamide concentration and the enzymatic activity of EFE using densitometric analysis.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.24 no.6
• /
• pp.715-722
• /
• 2011

In this paper, the behavior of nuclear-power plant subjected to an aircraft impact is performed using the parallel analysis. In the erstwhile study of an aircraft impact to the nuclear-power plant, it has been used that the impact load is applied at the local area by using the impact load-time history function of Riera, and the target structures have been restricted to the simple RC(Reinforced Concrete) walls or RC buildings. However, in this paper, the analysis of an aircraft impact is performed by using a real aircraft model similar to the Boeing 767 and a fictitious nuclear-power plant similar to the real structure, and an aircraft model is verified by comparing the generated history of the aircraft crash against the rigid target with another history by using the Riera's function which is allowable in the impact evaluation guide, NEI07-13(2009). Also, in general, it is required too much time for the hypervelocity impact analysis due to the contact problems between two or more adjacent physical bodies and the high nonlinearity causing dynamic large deformation, so there is a limitation with a single CPU alone to deal with these problems effectively. Therefore, in this paper, Message-Passing MIMD type of parallel analysis is performed by using self-constructed Linux-Cluster system to improve the computational efficiency, and in order to evaluate the parallel performance, the four cases of analysis, i.e. plain concrete, reinforced concrete, reinforced concrete with bonded containment liner plate, steel-plate concrete structure, are performed and discussed.

• Journal of Animal Science and Technology
• /
• v.54 no.2
• /
• pp.103-109
• /
• 2012

Present study was performed to investigate the effect of single and co-culture of adipocyte and muscle cell lines on cell differentiation. 3T3-L1 (adipocyte) and L6 (muscle) cell lines were single-cultured on the condition of 10% fetal bovine serum (FBS)/Dulbeco's modified eagle's medium (DMEM) for 48 h followed by culture within 5% FBS/DMEM as a growth media. Then, the growth media was replaced by differentiation media composed of 2% FBS/DMEM without additives in single- or co-culture of the 3T3-L1 and the L6 cells to induce differentiation of both cell types. In co-culture system, the 3T3-L1 and the L6 cells were grown in separated places by being seeded on a $0.4{\mu}m$ insert membrane and on the bottom of 6 well plate, respectively. Cell differentiation was measured using morphological investigation and cytosolic analysis of glycerol-3-phosphate dehydrogenase (GPDH; for 3T3-L1) and creatine kinase (CK; for L6). Based on the GPDH results, the presence of L6 cells did not stimulate 3T3-L1 differentiation showing more differentiation of 3T3-L1 cells in the single-culture compared to the co-culture condition. In contrast, 3T3-L1 cells in the co-culture promoted differentiation of L6 cells. Enzymatic analysis supported this result showing that 3T3-L1 cells showed statistically (P<0.05) higher GPDH activity in the single-culture than the co-culture, whereas CK results of L6 cells were vice versa (P<0.05). Overall, present results may indicate that co-culture system is more reliable and precise technique compared to single-culture. Further studies on several co-culture trials including different media conditions, supplementation of differentiating substances, molecular biological analysis, etc. should be required to obtain practical and fundamental mass data.

• Journal of Mechanical Science and Technology
• /
• v.17 no.11
• /
• pp.1801-1811
• /
• 2003

An experimental study was conducted to investigate the effects of air-side fouling and cleaning on the performances of various condenser coils used in unitary air-conditioning systems. A total of six condenser coils with different fin geometry and row number were tested. Performance tests were performed at three different conditions: clean-as-received, after fouling, and after cleaning. In all cases, it was observed that the fouling was mostly confined to the frontal face of the heat exchanger as reported in the previous investigations. The amount of deposited dust was more dependent on fin geometry for the single-row heat exchangers than for the double-row heat exchangers. The predominant effect of fouling was to cause a more significant increase in air-side pressure drop than a degradation in heat transfer performance. For the single-row heat exchangers, the pressure drop increased by 28 to 31%, while the heat transfer performance decreased by 7 to 12% at the standard air face velocity of 1.53 m/s depending on fin shape. For the double-row heat exchangers, the pressure drop increased by 22 to 37%, and heat transfer performance decreased by only 4-5% at the same air face velocity. Once the contaminated coils were cleaned according to the given cleaning procedure the original performance of the heat exchangers could almost be recovered completely. The pressure drop could be restored within 1 to 7% and the heat transfer performance could be recovered to within 1 to 5% of the originally clean heat exchangers. Therefore, it is concluded that a periodic application of the specified cleaning technique will be effective in maintaining the thermal performance of the condenser coils.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.32 no.4
• /
• pp.71-80
• /
• 1990

Model tests for the ultimate pullout resistance of anchorages and investigation of failure behaviors in cohesionless soil have been conducted. The factors affecting the anchorage are mostly the geometry of the system, and soil properties of sands. The main conclusions of the experimental work were as follows. 1. The load - displacement relationship can be a form of parabolic curve for all plates. 2. The change in ultimate pullout resistance of anchor is mostly affected by embedment ratio and size of anchor, and influenced to a lesser degree by its shape. 3. Critical embedment ratio which is defined as the failure mode changes from shallow to deep mode is increased with increasing height of anchor. 4. For a constant anchor height, as the width of anchor increases the ultimate pullout resistance also increases. However, considering the efficiency of anchor for unit area, width of anchor does not appear to have any sigrnificant contribution on increasing anchor city. 5. Anchor capacity has a linear relation to sand density for any given section and the rate of change increases as the section increases. Critical depth determining the failure patterns of anchor is decreased with a decrease of sand density. 6. With increasing inclination angle, size of anchor, and decreasing embedment ratio, the ultimate pullout resistance of anchor under inclined loading is significantly decreased. 7. The ultimate pullout resistance of double anchor, a method of improving single of anchor capacity, is influenced by the center - to - center spacing adjacent anchors. It is also found that tandem and parallel anchor rigging arrangements decrease the anchor system capacity to less than twice the single anchor capacity due to anchor interference.

• Journal of Power System Engineering
• /
• v.20 no.3
• /
• pp.22-28
• /
• 2016

Energy consumption rapidly increases with industrial development. therefore an interest in the efficiency of various power converters is increasing. Especially, the field of high-efficiency small motors widely distributed for industrial and family use is considered a very important field in terms of efficient energy usage, and accordingly, in the field of small electric equipment, the use of BLDC that allows high-efficiency drive in an inductor gradually increases. However, for the BLDC drive, information on the position of the rotor is essential. Both methods using a magnetic encoder and an optical encoder to detect the information on the position of the rotor obtain the information by three position sensitive devices, and if any one of these position sensitive devices fails to function, no positional information can be obtained, so there is a limitation in implementing a position sensor with high reliability. In the paper, proposes a new type of encoder that can obtain the positional information on the position of the rotor using a single position sensor in order to overcome the issues that it has to use numerous signal flows and that the reliability is reduced for the acquisition of positional information generated by using multiple position detectors. The encoder in the proposed method replaced the function of generating positional information from multiple sensors with the shape of the encoder plate and the capture function of MICOM. In order to verify the validity of the position detection technique by the proposed encoder, a prototype was produced, and an experiment using the capture function of DSP was conducted through this.

• Journal of Digital Contents Society
• /
• v.14 no.4
• /
• pp.447-454
• /
• 2013

As the surveillance CCTVs are increasing every year, big data image processing for the CCTV image data has become a hot issue. In this paper, we propose a Hadoop-based big data image processing technique to recognize a vehicle number from a large amount of automatic number plate images taken from CCTVs. We also implement the vehicle route tracking system that displays the moving path of the searched vehicle on Google Maps with the related information together. In order to evaluate the performance we compare and analysis the vehicle number recognition time for a lot of CCTV image data in Hadoop and the single PC environment.

• Journal of Korea Multimedia Society
• /
• v.2 no.3
• /
• pp.297-307
• /
• 1999

A character recognition system, where a large amount of character images arrive continuously in real time, must preprocess character images very quickly. Moreover, information loss due to image trans-formations such as geometric normalization and thinning needs to be minimized especially when character images are small and noisy. Therefore, we suggest a prompt and effective feature extraction method without transforming original images. For this, boundary pixels are defined in terms of the degree in classification, and those boundary pixels are considered selectively in extracting features. The proposed method is tested by a handwritten character recognition and a car plate number recognition. The experiments show that the proposed method is effective in recognition compared to conventional methods. And an overall reduction of execution time is achieved by completing all the required processing by a single image scan.