• 한국지반환경공학회 논문집
• /
• 제13권3호
• /
• pp.85-90
• /
• 2012

본 논문은 ABAQUS 유한 요소 프로그램을 사용하여 다층지반(화강풍화토-점토-화강풍화토)에서의 외말뚝과 군말뚝의 횡하중에 대한 영향을 설명한다. 본 연구에서의 변수는 캡이 없는 외말뚝과 캡이 있는 군말뚝으로, 파일의 직경은 0.5m, 길이는 10m인 말뚝을 사용하였다. 수치 해석은 말뚝의 간격을 (s=3D, 4D, 5D) 변화시켜 외말뚝과 군말뚝의 거동을 비교하기 위하여 수행되었다. $1{\times}3$군말뚝(leading pile, middle pile, trail pile)은 각각의 말뚝의 저항분포와 수평저항력을 조사하기 위하여 선정되었다. 점토의 해석모델은 Druker-Prager 구성관계를 이용하였고, 화강풍화토의 물성치는 기존의 논문을 사용하였으며, 말뚝은 탄성 원형 콘크리트로 모델링하였다. 해석 결과, 말뚝의 간격이 넓어짐에 따라 P-multiplier의 값이 leading pile의 영향을 덜 받는 것으로 나타났다. 또한, 단층지반이 다층지반에 비해 수평저항력이 약 4~20% 크게 작용하는 것으로 나타났다.

• 한국지진공학회논문집
• /
• 제3권3호
• /
• pp.45-54
• /
• 1999

지진의 연직성분에 의해 유발된 해진시 단일개단말뚝의 거동에 관한 이전의 연구들에서 단일개단말뚝의 지지력은 완전히 감소되었으며 관내토의 폐색도 완전히 파괴된 것으로 밝혀졌다 그러나 개단말뚝이더라도 말뚝의 관입길이가 길 경우 해진에 대하여 말뚝이 안정성을 유지할수 있고 개단강관말뚝일 경우에는 비교적 관입깊이가 짧을 경우에도 해진에 대하여 안정성을 유지할 수있을 것으로 예상된었다 본 연구에서는 초세립질 포화모래지반을 담고 잇는 소형압력토조에 단일개단말뚝 2개 또는 4개의 개단무리말뚝을 관입길이 7-40m로 모델링하여 관입시켰으며 각각의 말뚝에 대하여 압축정재하시험을 실시한후 극한지지력의 약 95%의 압축하중을 재하시킨 상태에서 해진의 진동을 작용시키면서 지지력의 감소를 확인하였고 해진 작용후의 각각의 말뚝에 대하여 압축정재하시험을 실시하였다. 해진시 천해에 설치된 단일개단말뚝과 군말뚝의 지지력은 감소되지 않았다 그러나 심해에 설치된 말뚝의 안정성은 말뚝의 지중관입 깊이에 좌우되었다 즉 27m이상 관입된 단일개단말뚝의 지지력은 안정하였으며 13m이상 관입된 2개 및 4개 군말뚝은 안정하였다 그런 7m 관입된 2개 군말뚝은 파괴되었으며 7m 관입된 4개 군말뚝의 지지력은 15%만큰 저감되었다.

• Geomechanics and Engineering
• /
• 제32권1호
• /
• pp.21-34
• /
• 2023

In order to analyze the effect of the cyclic lateral loading on the response of a pile-soil system, a full-scale single steel pile was subjected to one-way cyclic loading. The test pile was driven into a bi-layered soil consisting of a normally consolidated saturated clay overlying a silty sandy layer, the site being submerged by water up to one meter above the mudline in order to reproduce the conditions of an offshore pile foundation. The aim of this paper is to present the main results of interpretation of the cyclic lateral tests in terms of pile deflections, bending moment, and cyclic P-Y curves. From these latter an absolute secant reaction modulus E_AS,N was derived and a simple calculation model of the test single pile is proposed based on this modulus. Two applications of the proposed model are carried out, one with a 2D finite element modelling, and the second with a load transfer curves-based method.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 1999년도 봄 학술발표회 논문집
• /
• pp.447-454
• /
• 1999

The compressive capacity and the soil plugging resistance of single open-ended pipe pile were completely decreased in the previous study on the behavior of shorter single pile during simulated seaquake induced by the vertical component of earthquake. But the capacity of single open-ended pipe pile with greater penetration and the capacity of piles group with shorter penetration were expected to be stable after seaquake motion. In this study, first, 2-piles or 4-piles are driven into the calibration chamber included in saturated fine medium sand with several simulated penetrations, and the compressive load test for each piles group was performed. Then, about 95 % compressive load of the ultimate capacity was applied on the pile head during the simulated seaquake motion. Finally, In confirm the reduction of pile capacity during the simulated seaquake motion, the compressive load test for each single pile or piles group after seaquake motion was performed. During the simulated seaquake, the compressive capacity of open-ended pipe piles with greater penetration ( 〉about 27 m) was not degraded even in deep sea deeper than 220 m and soil plug within open-ended pipe pile installed in deep sea was stable after seaquake motion. Also, in the case of 2-piles or 4-pile groups, the compressive capacity after seaquake motion was not degraded at all regardless of pile penetration depth beneath seabed, sea water depth and seaquake frequency.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2005년도 춘계 학술발표회 논문집
• /
• pp.705-712
• /
• 2005

Among soft ground treatment methods with granular soil used in domestic, the sand compaction pile method has been utilized greatly, but, as a result of exhaustion of sand and increase of unit cost, a necessity of an alternative method is suggested. In this study, the static load tests for group crushed-stone compaction piles which were constructed at in-situ site were performed. Pile diameter was 700mm and area of loading plates were changed. The static load tests of single and group piles were performed for area replacement ratio of 20, 30 and 40%. Based on test results, bearing capacity of group crushed-stone compaction pile were estimated. The more both single pile and group pile increase, the more yield bearing capacity tended to increase. Also, the yield bearing capacity of a group pile is about 50% less than the yield bearing capacity of a single pile. If the ground reinforced with the crushed-stone compaction pile is replacement ratio of $20{\sim}40%$, RIYB of both single pile and group pile increases qualitative tendency of linear more than original ground

• 대한토목학회논문집
• /
• 제32권5C호
• /
• pp.199-210
• /
• 2012

본 연구에서는 3차원 탄-소성 유한차분해석을 통해 기존재하는 단독말뚝, $3{\times}3$및 $5{\times}5$ 군말뚝의 바로 아래 풍화암 지반에서 실시된 터널시공으로 인한 말뚝의 거동을 분석하였다. 수치해석에서는 터널굴착으로 인한 말뚝의 거동을 규명하기 위하여 지반/말뚝의 침하 및 전단응력전이(shear stress transfer) 메커니즘을 심도있게 분석하였다. 터널굴착으로 유발된 지반의 침하와 말뚝-지반 사이 경계면에서의 상대변위 발생으로 인해 말뚝에 작용하는 전단응력 및 축력의 분포가 매우 크게 변화하였다. 계산된 결과에 의하면 터널굴착으로 인해 말뚝의 두부로부터 말뚝길이의 약 80%에 해당되는 위치까지는 상향의 전단응력이 발생하였고, 그 하부에서는 하향의 전단응력이 발생하였다. 이로 인해 말뚝의 축력이 터널의 굴착에 따라 지속적으로 감소하고, 순수한 터널의 시공으로 인하여 말뚝에는 인장력이 발생하였는데 이로 인해 말뚝에는 최대 $0.36P_a$의 인장력이 발생하였다, 여기서 $P_a$는 터널굴착이전에 말뚝두부에 작용하는 설계하중이다. 말뚝의 거동은 경계면에서의 전단강도 발현 정도에 가장 큰 영향을 받는 것으로 나타났다. 군말뚝의 경우 일반적으로 말뚝의 숫자가 증가할수록 터널의 시공에 의해 말뚝의 침하가 증가하는 것으로 나타났으며, 이와는 반대로 말뚝의 축력변화는 군효과(shielding effect)로 인해 단독말뚝의 경우에 비해 작은 것으로 분석되었다. 터널굴착으로 인한 말뚝침하의 증가로 인한 겉보기지지력(apparent pile capacity) 감소는 단독말뚝에 비해 군말뚝에서 두드러지는 것으로 분석되었다.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2008년도 춘계 학술발표회 초청강연 및 논문집
• /
• pp.1132-1143
• /
• 2008

A single Column/Shaft which extended the pile to the column of the bridge with same diameter has better safety and economical profit, but it usually has larger lateral displacement due to lateral loads such as wind, earthquake, wave, etc. A series of horizontal pile load testing were performed to study the lateral behavior of single column/shaft with varying different free lengths and embedded pile lengths. Eight instrumented test piles were cast-in-placed by bonding strain gauges at certain locations on both faces of the pile to measure bending moment, from two-way loadings. Linear variable differential transformers(LVDTs) were installed to measure the lateral pile displacement. Based on this, it is found that the test single column/shaft with different free lengths shows different failure modes. If the test pile has a longer free length, the failure occurs at the near the ground surface, but the shorter one's failure occurs at the below the ground surface.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2010년도 춘계 학술발표회
• /
• pp.188-197
• /
• 2010

This paper presents experimental results of a series of 1-g shaking table model tests performed on end-bearing single piles and pile groups to investigate the effect of particle size on the dynamic behavior of soil-pile systems. Two soil-pile models consisting of a single-pile and a $4{\times}2$-pile group were tested twice; first using Jumoonjin sand, and second using Australian Fine sand, which has a smaller particle size. In the case of single-pile models, the lateral displacement was almost within 1% of pile diameter which corresponds to the elastic range of the pile. The back-calculated p-y curves show that the subgrade reaction of the Jumoonjin-sand-model ground was larger than that of the Australian Fine-sand-model ground at the same displacement. This phenomenon means that the stress-strain behavior of Jumoonjin sand was initially stiffer than that of Australian Fine sand. This difference was also confirmed by resonant column tests and compression triaxial tests. And the single pile p-y backbone curves of the Australian fine sand were constructed and compared with those of the Jumoonjin sand. As a result, the stiffness of the p-y backbone curves of Jumunjin sand was larger than those of Australian fine sand. Therefore, using the same p-y curves regardless of particle size can lead to inaccurate results when evaluating dynamic behavior of soil-pile system. In the case of the group-pile models, the lateral displacement was much larger than the elastic range of pile movement at the same test conditions in the single-pile models. The back-calculated p-y curves in the case of group pile models were very similar in both sands because the stiffness difference between the Jumoonjin-sand-model ground and the Australian Fine-sand-model ground was not significantly large at a large strain level, where both sands showed non-linear behavior. According to a series of single pile and group pile test results, the evaluation group pile effect using the p-multiplier can lead to inaccurate results on dynamic behavior of soil-pile system.

• Geomechanics and Engineering
• /
• 제23권6호
• /
• pp.513-521
• /
• 2020

In this paper, due to the need for cutting cement-soil group pile composite foundation under the 7-story masonry structure of Zhenghe District and the shield tunnel of Zhengzhou Metro Line 5, a field test was conducted to directly cut cement-soil single pile composite foundation with diameter Ф=500 mm. Research results showed that the load transfer mechanism of composite foundation was not changed before and after shield tunnel cut the pile, and pile body and the soil between piles was still responsible for overburden load. The construction disturbance of shield cutting pile is a complicated mechanical process. The load carried by the original pile body was affected by the disturbance effect of pile cutting construction. Also, the fraction of the load carried by the original pile body was transferred to the soil between the piles and therefore, the bearing capacity of composite foundation was not decreased. Only the fractions of the load carried by pile and the soil between piles were distributed. On-site monitoring results showed that the settlement of pressure-bearing plates produced during shield cutting stage accounted for about 7% of total settlement. After the completion of pile cutting, the settlements of bearing plates generated by shield machine during residual pile composite foundation stage and shield machine tail were far away from residual pile composite foundation stage which accounted for about 15% and 74% of total settlement, respectively. In order to reduce the impact of shield cutting pile construction on the settlement of upper composite foundation, it was recommended to take measures such as optimization of shield construction parameters, radial grouting reinforcement and "clay shock" grouting within the disturbance range of shield cutting pile construction. Before pile cutting, the pile-soil stress ratio n of composite foundation was 2.437. After the shield cut pile is completed, the soil around the lining structure is gradually consolidated and reshaped, and residual pile composite foundation reaches a new state of force balance. This was because the condensation of grouting layer could increase the resistance of remaining pile end and friction resistance of the side of the pile.

• 한국터널지하공간학회 논문집
• /
• 제19권3호
• /
• pp.389-407
• /
• 2017

본 연구는 단독말뚝 또는 군말뚝 형태의 기초 하부를 터널이 근접통과할 경우 말뚝의 거동을 파악하기위해 3차원 유한요소해석을 수행하였다. 이때 터널과 말뚝기초 사이의 지반보강 조건별로 수치해석을 수행하여 결과를 분석하였다. 수치해석에서는 터널굴착으로 인해 유발된 말뚝침하, 축력, 전단응력 및 터널 주변지반의 전체변위를 고찰하였다. 단독말뚝의 두부침하는 지반보강의 범위가 가장 넓은 경우 지반보강을 고려하지 않은 말뚝에 비해 약 16% 감소하며, 말뚝의 최대 축력 또한 지반보강을 고려하지 않은 말뚝에 비해 약 30% 감소하는 것으로 분석되었다. 터널굴착에 따른 말뚝의 거동은 지반보강길이 (종방향 보강)보다는 보강각도(횡방향 보강)에 대해 더 크게 영향을 받는 것으로 분석되었다. 한편 오직 기초판 보강만을 실시한 군말뚝의 경우 선단부근 지반의 변위는 보강을 고려하지 않은 조건의 지반 변위와 비슷하게 나타났다. 이에 비해 말뚝두부에서는 기초판이 말뚝을 크게 구속하여 타 조건 말뚝의 경우에 비해 말뚝상부에서 축력이 약 2.5배 증가하는 것으로 분석되었다. 본 연구를 통해 보강조건에 따른 단독말뚝 및 군말뚝의 거동에 영향을 미치는 주요인자를 심도 있게 고찰하였다.