• International Journal of Computer Science & Network Security
• /
• v.23 no.9
• /
• pp.8-16
• /
• 2023

In Japan, high-speed ground transportation service using linear motors at speeds of 500 km/h is scheduled to begin in 2027. To accommodate 5G services in trains, a subcarrier spacing frequency of 30 kHz will be used instead of the typical 15 kHz subcarrier spacing to mitigate Doppler effects in such high-speed transport. Furthermore, to increase the cell size of the 5G mobile system, multiple base station antennas will transmit identical downlink (DL) signals to form an expanded cell size along the train rails. In this situation, the forward and backward antenna signals are Doppler-shifted in opposite directions, respectively, so the receiver in the train may suffer from estimating the exact Channel Transfer Function (CTF) for demodulation. In a previously published paper, we proposed a channel estimator based on Delay and Doppler Profiler (DDP) in a 5G SISO (Single Input Single Output) environment and successfully implemented it in a signal processing simulation system. In this paper, we extend it to 2×2 MIMO (Multiple Input Multiple Output) with spatial multiplexing environment and confirm that the delay and DDP based channel estimator is also effective in 2×2 MIMO environment. Its simulation performance is compared with that of a conventional time-domain linear interpolation estimator. The simulation results show that in a 2×2 MIMO environment, the conventional channel estimator can barely achieve QPSK modulation at speeds below 100 km/h and has poor CNR performance versus SISO. The performance degradation of CNR against DDP SISO is only 6dB to 7dB. And even under severe channel conditions such as 500km/h and 8-path inverse Doppler shift environment, the error rate can be reduced by combining the error with LDPC to reduce the error rate and improve the performance in 2×2 MIMO. QPSK modulation scheme in 2×2 MIMO can be used under severe channel conditions such as 500 km/h and 8-path inverse Doppler shift environment.

• The Bulletin of The Korean Astronomical Society
• /
• v.44 no.2
• /
• pp.51.1-51.1
• /
• 2019

At the commissioning phase of KVN from 2009 to 2013, single-dish survey and monitoring observations were performed toward about 1000 evolved stars and about 60 relatively strong SiO and H2O maser sources respectively. Based on these single-dish results and VLBI feasibility test observations at K/Q/W/D bands in 2014, KVN Key Science Project (KSP) has started from 2015 and will be completed in 2019 as KSP phase I. Here we present the overview of observational studies on evolved stars using KVN. In KSP phase I, we have focused on nine KSP sources which show a successful astrometrically registered maps of SiO and H2O masers using the source frequency phase referencing method. We aim at investigating the spatial structure and dynamical effect from 43/42/86/129 GHz SiO to 22 GHz H2O maser regions associated with a stellar pulsation and development of asymmetry in circumstellar envelopes. Using the combined network KaVA (KVN+Japanese VLBI network VERA), KaVA Large Program titled on "Expanded Study on Stellar Masers: ESTEMA Phase I" was performed from 2015 to 2016. Based on ESTEMA Phase I, EAVN Large Program titled on "EAVN Synthesis of Stellar Maser Animations: ESTEMA Phase II" was also performed from 2018. The ESTEMA II project aims to publish composite animations of circumstellar H2O and SiO masers, which taken from up to 6 long-period variable stars with a variety of the pulsation periods (333-1000 days). The animations will exhibit the three-dimensional kinematics of the maser gas clumps with complexity caused by stellar pulsation-driven shock waves and anisotropy of clump ejections from the stellar surface. Adding three EAVN telescopes (Tianma 65m, Nanshan 26m and NRO 45m telescopes) with KaVA always secures the high quality of the maser image frames through the monitoring program.

• Korean Circulation Journal
• /
• v.52 no.3
• /
• pp.233-242
• /
• 2022

Background and Objectives: For adult men with congenital heart disease (ACHD), data on erectile dysfunction (ED) is limited. We aimed to assess the frequency of ED, its role in patient-physician communication and to identify parameters predicting ED. Methods: Male ACHD ≥18 years registered at the German National Register for Congenital Heart Defects were invited to participate in an online questionnaire about sexual health. Participants with presumed ED according to International Index of Erectile Function Score were compared to patients without ED. Results: The 371 patients responded to the questionnaire (83% with moderate to highly complex ACHD). The 43% presented with more than mild ED. When ED was present, patients complained about general anxiety to be sexually active more often (p<0.05) and underwent sexual activity less frequently compared to those without ED (p<0.05). Age ≥40 years (odds ratio [OR], 3.04; p=0.002), being single (OR, 6.82; p<0.0001), anxiety to be sexually active (OR, 2.64; p=0.0002) and psychiatric disease (OR, 4.33; p<0.0007) emerged as independent predictors for ED. Overall, patients sought medical advice in 6.7% of cases, whilst 29.6% would appreciate an active approach by the physician to address this sensitive topic. Conclusions: ED is affecting one third to one half of male ACHD according to a questionnaire-based analysis. Older age, being single, fear of sexual activity due to ACHD and psychiatric disorder emerged as independent predictors for ED. These parameters can easily be assessed to identify patients at risk. ED should be addressed proactively by health professionals.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.32 no.6
• /
• pp.661-668
• /
• 2012

Wireless sensor network is one of prospective methods for railway monitoring due to the long-term operation and low-maintenance performances. How to supply power to the wireless sensor nodes has drawn much attention recently. In railway monitoring, the idea of converting ambient vibration energy from vibration of railway track induced by passing trains to electric energy has made it a potential way for powering the wireless sensor nodes. In this paper, a bimorph cantilever piezoelectric energy harvester was designed based on a single degree-of-freedom model. Experimental test was also performed to validate the design. The first natural frequency of the bimorph piezoelectric energy harvester was decreased from 117.1 Hz to 65.2 Hz by adding 4 gram tip mass to the free end of the 8.6 gram energy harvester. In addition, the power generation of the piezoelectric energy harvester with 4 gram tip mass at resonant frequency was increased from 0.14 mW to 0.74 mW from $2.06m/s^2$ base excitation compared to stand-alone piezoelectric energy harvester without tip mass.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.60 no.9
• /
• pp.1651-1655
• /
• 2011

The reference impedances which is about 95% supply impedance value of residential consumers' supply impedances was published by IEC in 1980. The reference impedances are the standard values for use in determining the voltage disturbance characteristics of electrical equipment like the flicker. In IEC 60725, the reference impedances for premises having service current capacities less than 100A per phase and for service current capacities more than 100A per phase are recommended. And these reference impedances are targeted for the countries using 50Hz power frequency. Because of the frequency difference, the reactance values of the reference impedances will be increased in 60Hz power system like Korea, And also the reference impedances are different significantly each other according to declared voltage variation, power consumption and service wire length etc. Therefore It is needed to calculate the reference impedances suitable for domestic low-voltage power system. In this paper, the reference impedances for service current capacities less than 100A in 220/380V, 60Hz single-phase two wire and three-phase four wire low-voltage system are calculated, And the equations for service current capacities more than 100A to calculate the modulus value of maximum supply impedances are suggested base on IEC 60725 and the reference impedances for those are calculated on service current of 100A per phase.

• ETRI Journal
• /
• v.34 no.5
• /
• pp.674-683
• /
• 2012

We propose a slot antenna consisting of a rectangular slot on the ground plane, fed by a microstrip line with a rectangular-ring-shaped tuning stub that can be deployed in ultra-wideband (UWB) communication systems to avoid interference with wireless local area network (WLAN) communication. Our antenna can achieve a single band-notched property from the 5 GHz frequency to the 6 GHz frequency owing to a controllable band notch that uses L- and J-shaped parasitic elements. The antenna characteristics can be modified to tune the band-notched property (4 GHz to 5 GHz or 6 GHz to 7 GHz) and the bandwidth of the band notch (1 GHz to 2 GHz). Furthermore, the shifted notch with enhanced width of the band notch from 1 GHz to 1.5 GHz is described in this paper. The UWB slot antenna and L- and J-shaped parasitic elements also provide the band-rejection function for reference in the WiMAX (3.5 GHz) and WLAN (5 GHz to 6 GHz) regions of the spectrum. Experiment results evidence the return loss performance, radiation patterns, and antenna gains at different operational frequencies.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.59 no.11
• /
• pp.2032-2037
• /
• 2010

This paper describes a design of dual band amplifier using left handed (LHJ) transmission line, which is a part of composite right/left handed (CRLH) transmission line. It is well known that CRLH transmission lines show dual band frequency response. At first, two single-band amplifiers for frequency f1 and f2 are designed, and their matching networks at both amplifiers are synthesized into the dual band matching network by adopting CRLH structure. As an example for proving the validity of the proposed design, a dual band amplifier operating at 1800MHz and 2300MHz is designed, fabricated and measured. The simulation and measurement show that the proposed amplifier operates well at the desired dual bands with the gain of 13.65dB and 19dB at 1850MHz and 2360MHz, respectively, and a good matching performances. In addition, a quite good agreement between the simulation and measurement is observed.

• Journal of Communications and Networks
• /
• v.18 no.6
• /
• pp.913-925
• /
• 2016

In-band wireless full-duplex is a promising technology that enables a wireless node to transmit and receive at the same time on the same frequency band. Due to the complexity of self-interference cancellation techniques, only base stations (BSs) are expected to be full-duplex capable while user terminals remain as legacy half-duplex nodes in the near future. In this case, two different nodes share a single subchannel, one for uplink and the other for downlink, which causes inter-node interference between them. In this paper, we investigate the joint problem of subchannel assignment and power allocation in a single-cell full-duplex orthogonal frequency division multiple access (OFDMA) network considering the inter-node interference. Specifically, we consider two different scenarios: i) The BS knows full channel state information (CSI), and ii) the BS obtains limited CSI through channel feedbacks from nodes. In the full CSI scenario, we design sequential resource allocation algorithms which assign subchannels first to uplink nodes and then to downlink nodes or vice versa. In the limited CSI scenario, we identify the overhead for channel measurement and feedback in full-duplex networks. Then we propose a novel resource allocation scheme where downlink nodes estimate inter-node interference with low complexity. Through simulation, we evaluate our approaches for full and limited CSIs under various scenarios and identify full-duplex gains in various practical scenarios.

• The KIPS Transactions:PartB
• /
• v.15B no.5
• /
• pp.493-500
• /
• 2008

Although modern day people gather many data from the network, the users want only the information needed. Using this technology, the users can extract on the data that satisfy the query. As the previous studies use the single data in the document, frequency of the data for example, it cannot be considered as the effective data clustering method. What is needed is the effective clustering technology that can process the electronic network documents such as the e-mail or XML that contain the tags of various formats. This paper describes the study of extracting the information from the user query based on the multi-attributes. It proposes a method of extracting the data such as the sender, text type, time limit syntax in the text, and title from the e-mail and using such data for filtering. It also describes the experiment to verify that the multi-attribute based clustering method is more accurate than the existing clustering methods using only the word frequency.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.9 no.2
• /
• pp.545-563
• /
• 2015

Energy harvesting (EH) and network coding (NC) have emerged as two promising technologies for future wireless networks. In this paper, we combine them together in a single system and then present a time switching-based network coding relaying (TSNCR) protocol for the two-way relay system, where an energy constrained relay harvests energy from the transmitted radio frequency (RF) signals from two sources, and then helps the two-way relay information exchange between the two sources with the consumption of the harvested energy. To evaluate the system performance, we derive an explicit expression of the outage probability for the proposed TSNCR protocol. In order to explore the system performance limit, we formulate an optimization problem to minimize the system outage probability. Since the problem is non-convex and cannot be directly solved, we design a genetic algorithm (GA)-based optimization algorithm for it. Numerical results validate our theoretical analysis and show that in such an EH two-way relay system, if NC is applied, the system outage probability can be greatly decreased. Moreover, it is shown that the relay position greatly affects the system performance of TSNCR, where relatively worse outage performance is achieved when the relay is placed in the middle of the two sources. This is the first time to observe such a phenomena in EH two-way relay systems.