• Transactions on Electrical and Electronic Materials
• /
• v.8 no.6
• /
• pp.286-288
• /
• 2007

The research and development for the solid oxide fuel cell have been promoted rapidly and extensively in recent years, because of their high efficiency and future potential. Therefore this paper describes the manufacturing method and characteristics of anode electrode for solid oxide fuel cell, by the way, Ni-YSZ materials are used as anode of solid oxide fuel cell widely. In order to reduce production costs, we have fabricated single solid oxide fuel cell by doctor blade and screen printing method. Disk-type planar solid oxide fuel cell with an effective electrode area of about $7cm^2$ were fabricated and run for 500 h to investigate cell performance. The current density at a voltage of 0.7 V was $850mA/cm^2$.

• International Journal of Air-Conditioning and Refrigeration
• /
• v.9 no.2
• /
• pp.8-18
• /
• 2001

The direct simulation Monte Carlo Method is applied to investigate the two-dimensional flow fields of a turbomolecular pump(TMP) in both molecular and transition flow regions. The pumping characteristics of the TMP are investigated for a wide range of the Knudsen number. The maximum of compression ratio and of pumping speed strongly depend on the Knudsen number in transition region, while they weakly depend on the Knudsen number in free molecular flow region. The present numerical results show good agreement with the previously known experimental data. Finally. the results of the single blade row in both molecular and transition regions are used to predict the overall performance of a TMP, which has three kinds of blade with 24-rows.

• Journal of the Society of Naval Architects of Korea
• /
• v.41 no.2
• /
• pp.33-46
• /
• 2004

The cavitating noise of underwater propeller is considered numerically in this study. The main purpose of this research is to analyze these noise sources from marine propeller. The approach for investigation is a potential based panel method coupled with acoustic analogy. To predict propeller sheet cavitation noise, the blade surface cavity is considered as a single valued pulsating volume of vapor attached to the blade surface. The time dependent cavity volume data are used for noise prediction. Furthermore, we analyze hydrofoil cavitation bubble behavior and noise using Eulerian/Lagrangian approach. Through this study, we can analyze dominant noise source of marine propeller and provide a basis for proper noise control strategies.

• Journal of Power System Engineering
• /
• v.2 no.1
• /
• pp.39-44
• /
• 1998

Computational grids used in the numerical simulation of multi staged turbomachinery flow fields are generated. A multiblock structure simplifies the creation of structured H-grids about complex turbomachinery geometries and facilitate the creation of a grid for multi-row topologies. The numerical algorithm adopts the combination of the algebraic and elliptic method to create the internal grids efficiently and quickly. The input module is made of the results of the preliminary design, i.e., flow-path, aerodynamic conditions along the spanwise direction, and the blade profile data. The final grids generated from each module of the system are used as the preprocessor for the performance prediction of the single row cascades and the flow simulation inside the multi staegd blade passage. Application to low pressure compressor of industrial gas turbine engines was demonstrated to be very reliable and practical in support of design activities.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.12 no.1
• /
• pp.83-94
• /
• 2000

The performance of a turbomolecular pump(TMP) in both molecular and transition flow regions is predicted by the numerical solutions of the Boltzmann equation obtained by the direct simulation Monte Carlo method. The compression characteristics of the TMP are investigated for a wide range of the Knudsen number( Kn ). The maximum compression ratios strongly depend on Kn in transition region, while do they weakly on Kn in free molecular flow region. The present numerical results of the single blade row in both molecular and transition regions are used to predict the overall performance of a TMP, which has three kinds of blade with 24-rows.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.20 no.1
• /
• pp.29-35
• /
• 2010

This paper studies causes of the L-1 blade damage of a low pressure turbine, which was found during the scheduled maintenance, in 500 MW fossil power plants. Many failures of turbine blades are caused by the coupling of aerodynamic forcing with bladed-disk vibration characteristics. In this study the coupled vibration characteristics of the L-1 turbine bladed-disk in a fossil power plant is shown for the purpose of identifying the root cause of the damage and confirming equipment integrity. First, analytic and experimental modal analysis for the bladed-disk at zero rpm as well as a single blade were performed and analyzed in order to verify the finite element model, and then steady stresses, natural frequencies and corresponding mode shapes, dynamic stresses were calculated for the bladed-disk under operation. Centrifugal force and steady steam force were considered in calculation of steady and dynamic stress. The proximity of modes to sources of excitation was assessed by means of an interference diagram to examine resonances. In addition, fatigue analysis was done for the dangerous modes of operation by a local strain approach. It is expected that these dynamic characteristics will be used effectively to identify the root causes of blade failures and to perform prompt maintenance.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.30 no.2
• /
• pp.111-117
• /
• 2017

In this paper, a local deformation effect in thin-walled box beams is investigated via a finite element modal analysis. The analysis is carried out for single-cell and multi-cell box beam configurations. The single-cell box beam with and without a neck, which mimics a simple wind-turbine blade, is analyzed first. The results obtained by shell elements are compared to those of one-dimensional(1D) beam elements. It is observed that the wall thickness plays a crucial role in the natural frequencies of the beam. The 1D beam analysis deviates from the shell analysis when the wall thickness is either thin or thick. The shell modes(local deformations) are dominant as it becomes thin, whereas the shear deformation effects are significant as it does thick. The analysis is extended to the single-cell box beam with a neck, in which the shell modes are confined to near the neck. Finally the multi-cell box beam with a taper, which is quite similar to real wind-turbine blade configuration, is considered to investigate the local deformation effect. The results reveal that the 1D beam analysis cannot match with the shell analysis due to the local deformation, especially for the lagwise frequencies. There are approximately 5~7% errors even if the number of segments is increased.

• International Journal of Precision Engineering and Manufacturing
• /
• v.4 no.4
• /
• pp.32-38
• /
• 2003

An analytical model of the interference phenomena in the centerless grinding process is developed to investigate their effects on the roundness profile of a centerless ground workpiece. In this work, the regulating wheel and work-rest blade interferences are modeled as a single point contact. The grinding wheel interference is modeled as multiple points contact because material removal is determined by the duration of contact. The computer simulation results show good agreement with the experimental data. From this work, the existence and effects of the interference phenomena in the centerless grinding process are found.

• Journal of Korean Physical Therapy Science
• /
• v.26 no.1
• /
• pp.22-34
• /
• 2019

Purpose: The purpose of this study was to investigate the effects of body blade and Thera band exercise on upper extremity strength, grip strength and balance of university students. Design: Single Blind Randomized Controlled Trial. Method: twenty healthy adults, participated in this study, and were recruited by G University in Gimcheon Korea. The subjects were randomly divided into A group that went through Thera band exercise and B group that went through Body blade exercise. Each group had 10 subjects. All subjects did the experiment for 3 times a week for 3weeks. Spss was used for statistical analysis. Result: 1) Grip strength: After exercising, for the BE group, there were statistically significant differences in dominant and non-dominant hand. However, for the TE group, there were no significant statistical differences in both hands. 2) muscle strength: In the TE group there were no significant statistical differences in the dominant and non-dominant arm. But in the BE group there were differences which were found. 3) balance: After exercising, both groups had no significant statistical difference in medial lateral balance. In anterior and posterior balance, TE group had no statistical significant difference but BE group did. Conclusion: To improve muscle strength balance and grip strength, body blade exercise is more effective than Thera band exercise.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• v.y2005m4
• /
• pp.349-354
• /
• 2005

In this paper, a small supersonic wind tunnel is designed and built to study the flow characteristics of a supersonic impulse turbine cascade. The flow is visualized by means of a single pass Schlieren system. The supersonic cascade with 2-dimensional supersonic nozzle was tested for various blade leading edge shapes and gaps between the nozzle and cascade. Highly complicated flow patterns including shocks, nozzle-cascade interaction and shock boundary layer interactions are observed.