• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2014년도 춘계학술대회 논문집
• /
• pp.128-134
• /
• 2014

A Experimental study on frequency characteristics of the microphone array covered with Kevlar in closed test section wind tunnel. Microphones that are flush mounted in a closed test section wall of wind tunnel are subject to very high flow noise resulting from the turbulence in the wall boundary layer. At this time the microphones measure the strong hydrodynamic fluctuations generated by the flow. The phenomena are referred to a microphone self-noise and a method for reducing this has studied. In this paper the array that covered with acoustically transparent Kevlar sheet was designed and made to reduce the flow-induced self-noise. For the validation frequency characteristics of the Kevlar, the microphone array was installed on the wall and test was performed for white noise and sine wave of several frequencies using loudspeaker. In addition, the paper compared the signals as a tension of Kevlar. The results were presented that tend to decrease the sound pressure level at high frequency above 3500Hz according to existence of Kevlar.

• Advances in aircraft and spacecraft science
• /
• 제7권3호
• /
• pp.251-269
• /
• 2020

Euclid is an optical/near-infrared survey mission of the European Space Agency (ESA) to investigate the nature of dark energy, dark matter and gravity by observing the geometry of the Universe and the formation of structures over cosmological timescales. The Euclid spacecraft mechanical architecture comprises the Payload Module (PLM) and the Service Module (SVM) connected by an interface structure designed to maximize thermal and mechanical decoupling. This paper shortly illustrates the mechanical system of the spacecraft and the mechanical verification philosophy which is based on the Structural and Thermal Model (STM), built at flight standard for structure and thermal qualification and the Proto Flight Model (PFM), used to complete the qualification programme. It will be submitted to a proto-flight test approach and it will be suitable for launch and flight operations. Within the overall verification approach crucial mechanical tests have been successfully performed (2018) on the SVM platform and on the sunshield (SSH) subsystem: the SVM platform static test, the SSH structure modal survey test and the SSH sine vibration qualification test. The paper reports the objectives and the main results of these tests.

• Smart Structures and Systems
• /
• 제25권5호
• /
• pp.543-557
• /
• 2020

This paper presents a series of experimental and numerical investigations on a vertical isolation system with quasi-zero stiffness (QZS) property. The isolation system comprises a linear helical spring and disk spring. The disk spring is designed to provide variable stiffness to the system. Orthogonal static tests with different design parameters are conducted to verify the mathematical and mechanical models of the isolation system. The deviations between theoretical and test results influenced by the design parameters are summarized. Then, the dynamic tests for the systems with different under-load degrees are performed, including the fast sweeping tests, harmonic excitation tests, and half-sine impact tests. The displacement transmissibility, vibration reduction rate, and free vibration response are calculated. Based on the test results, the variation of the transmission rule is evaluated and the damping magnitudes and types are identified. In addition, the relevant numerical time history responses are calculated considering the nonlinear behavior of the system. The results indicate that the QZS isolation system has a satisfactory isolation effect, while a higher damping level can potentially promote the isolation performance in the low-frequency range. It is also proved that the numerical calculation method accurately predicts the transmission character of the isolation system.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2001년도 춘계학술발표대회 논문집
• /
• pp.19-22
• /
• 2001

This paper proposes a double cantilever sandwich-beam method for evaluating the frequency dependence of material dynamic characteristics. The flexural vibration of a double cantilever sandwich-beam specimen with a partially inserted rubber layer was studied using a finite element simulation in combination with the sine-sweep test. Quadratic relationships of dynamic elastic modulus and material loss factor of rubbers with frequency were quantitatively suggested employing the least square error method.

• 대한기계학회논문집A
• /
• 제26권7호
• /
• pp.1393-1400
• /
• 2002

A double cantilever sandwich-beam method has been applied to the evaluation of the frequency dependence of dynamic elastic modulus and material loss factor of EPDM rubbers. The flexural vibration of a double cantilever sandwich-beam specimen with an inserted rubber layer was studied using a finite element simulation in combination with the sine-sweep test. Effects of the rubber layer length on the dynamic characteristics were also investigated: reliable values were measured when the length of the inserted rubber layer was larger than and equal to 50% of the effective specimen length. The values were compared with those obtained by the dynamic mechanical analysis and the simple resonant test. Relationships of the dynamic characteristics of rubbers with frequency could be determined using the least square error method.

• 한국지진공학회논문집
• /
• 제7권4호
• /
• pp.71-79
• /
• 2003

사장교에서 케이블은 교량 전체에 있어서 매우 중요한 요소이다. 차량, 바람 혹은 풍우에 의한 케이블의 진동은 교량의 안전성과 사용성을 감소시키는 주요 원인이 되어왔으며 이러한 문제를 해결하는 효과적인 방법중의 하나는 케이블 댐퍼를 설치하는 것이다. 이 케이블 댐퍼를 최적으로 설계하기 위해서는 케이블의 동특성을 정확하게 평가해야 하며 케이블 동특성치를 얻기 위해서는 정확한 가진이 필요하다. 따라서 본 연구에서는 케이블 가진시스템을 개발하고 성능을 평가하기 위해 케이블 가진시스템의 운동방정식을 유도하였으며, 케이블 가진기를 케이블 모형에 설치하여 정현진동실험과 공진진동실험을 수행하여 케이블의 동특성을 효과적으로 구하였다.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2004년도 추계학술대회논문집
• /
• pp.242-247
• /
• 2004

In this study was proposed a transient response analysis technique of a rotor system, applying the generalized FE modeling method of a rotor-bearing system considering a base-transferred shock force and together the state-space Newmark method of direct time integration scheme based on the average velocity concept. Experiments were performed to a test rig of a mock-up rotor-bearing system with series of half-sine shock waves imposed by an electromagnetic shaker, and quantitative error analyses between analytical and experimental results were carried out. The transient reponses of the rotor were sensitive to duration times and shape-qualities of the shock waves, and overally the analytical results agreed quite well with the experimental ones. Particularly, in cases that the frequencies, $1/(2{\times}duration\;time)$, of the shock waves were close to the critical speed of the rotor-bearing system, resonances occurred and the transient responses of the rotor were amplified.

• Journal of Biosystems Engineering
• /
• 제23권4호
• /
• pp.327-334
• /
• 1998

This work was intended to determine the optimum values of the cab suspension parameters by a simulation method in order to minimize the seat accelerations of agricultural tractors in the frequencies lower than 50Hz. A dynamic model of cab motions was developed and verified using a tractor excited over half-sine bumps on a concrete test road. A simulation program based on the model was also developed. A method was proposed to determine the optimum values of the suspension parameters. It was found that the natural frequencies of the cab and seat suspensions must be apart as far as possible until the sum of seat and cab accelerations is minimized, which also reduces the seat accelerations maximally.

• Composites Research
• /
• 제14권3호
• /
• pp.69-76
• /
• 2001

본 연구에서는 고무의 동탄성계수와 손실계수에 대한 주파수 의존성을 평가하기 위한 새로운 양팔 샌드위치보 시험법을 제안하였다. 고무층이 삽입되어 접착된 양팔샌드위치보 시험편의 횡진동 거동에 대해 유한요소 모달변형률 에너지법을 조합한 사인스위프 시험을 이용하여 분석하고 동적 점 탄성해석시험 및 단순공진시험 결과와 비교 검토하였다. 양팔 샌드위치보의 횡진동 모드에 따라 고무층의 주파수별 동탄성계수와 재료감쇠계수를 측정하고, 이들을 최소자승오차법에 의거하여 주파수의 이차함수로 회귀시켜 평가할 수 있었다.

• 한국지반공학회논문집
• /
• 제37권11호
• /
• pp.71-81
• /
• 2021

본 연구는 액상화 현상을 모사할 수 있는 1g 진동대 실험(Shaking table test)을 이용하여 포화 사질토 지반 위 제방 존재 유무에 따른 지반 조건 대상으로 재액상화 거동에 대하여 연구하였다. 실험에 사용된 지반은 실리카 모래를 사용하였으며, 지반조성은 액상화층 50cm(Case 1)와 비액상화층 17.5cm와 액상화층 32.5cm인 경우(Case 2)로 2가지 조건으로 수중낙사법을 이용하여 조성하였다. 제방은 높이 10cm, 사면 기울기는 1 : 1.8 비율로 고정하여 조성하였다. 지진파는 5Hz의 정현파를 8초간 가진을 진행하여 총 1차부터 5차 가진을 수행하였다. Case 1의 경우 자유장 위치에서 1차 가진 시 모든 깊이에 액상화가 발생하였으며, 3차 가진 시 5cm 깊이를 제외한 모든 깊이에서 액상화 현상이 발생하지 않음을 확인하였다. 제방 중심 위치에서는 1차 가진 시 20cm 깊이까지 액상화가 발생하였으며, 2차 가진 시 5cm 깊이를 제외한 모든 깊이에서 액상화 현상이 발생하지 않음을 확인하여, 제방 구조물 설치 시 재액상화 거동에 대하여 평가하였다.