• 대한기계학회논문집B
• /
• 제26권6호
• /
• pp.772-778
• /
• 2002

A numerical analysis of turbulent gas-particle two-phase flow is performed in conjunction with the experiments of Fackrell ＆ Robins and Raupach & Legg that considered ground-level source and/or elevated source flat plate flow. K-$\omega$ turbulence model is used in order to analyze fully turbulent flow field and the concentration equation with settling velocity is adopted for the concentration field. The model of Einstein and Chien is applied that couples the velocity field and the concentration field. Turbulent eddy viscosity is re-evaluated in this model. The present numerical results have good agreement between the simulation and the experimental data for the mean flow velocities and particle concentrations. While the previous study shows about 27% error in the vicinity of the source of particle concentration, the .present study allows about 14% error. A new turbulent gas-particle flow model developed by this study is able to cut down error by 13% at a near source.

• Journal of Power Electronics
• /
• 제18권1호
• /
• pp.70-80
• /
• 2018

A novel strategy based on a zero common mode voltage pulse-width modulation (ZCMV-PWM) technique and zero-sequence circulating current (ZSCC) feedback control is proposed in this study to eliminate ZSCCs between three-level neutral point clamped (NPC) voltage source inverters, with common AC and DC buses, that are operating in parallel. First, an equivalent model of ZSCC in a three-phase three-level NPC inverter paralleled system is developed. Second, on the basis of the analysis of the excitation source of ZSCCs, i.e., the difference in common mode voltages (CMVs) between paralleled inverters, the ZCMV-PWM method is presented to reduce CMVs, and a simple electric circuit is adopted to control ZSCCs and neutral point potential. Finally, simulation and experiment are conducted to illustrate effectiveness of the proposed strategy. Results show that ZSCCs between paralleled inverters can be eliminated effectively under steady and dynamic states. Moreover, the proposed strategy exhibits the advantage of not requiring carrier synchronization. It can be utilized in inverters with different types of filter.

• 응용통계연구
• /
• 제29권1호
• /
• pp.181-192
• /
• 2016

옵션의 가격을 결정하는 문제에서 블랙-숄즈 모형이 가지는 단점을 보완하기 위해 블랙-숄즈 가격을 선도항으로 하여 보정항을 구하는 근사적 옵션가격의 결정방법을 고려하였다. 이러한 근사적 가격결정 방법들은 비교적 적은 자료를 가지고 간단한 계산으로 다양한 형태의 위험중립 확률분포에 의한 옵션가격을 계산할 수 있다. 이 논문에서는 일반적으로 관찰되는 시장상황을 모사한 모의실험과 실제 시장에서 관측되는 KOSPI200 옵션가격 자료를 통해 몇 가지 근사방법들의 적합성과를 비교, 평가하였다. 헤르미트 다항식 계열의 Edgeworth 확장과 A-type Gram-Charlier, C-type Gram-Charlier 방법, NIG 분포를 이용하는 방법, 비선형 회귀를 이용한 점근적 근사방법이 고려되었다. 모의실험에서는 순수 점프 레비 확률과정 가운데 옵션가격이 닫힌 해의 형태로 존재하는 Variance gamma 과정을 가정하여 자료를 생성하였다. 모의실험과 실제 자료분석의 결과, 분포함수를 먼저 근사하여 가격을 계산하는 것보다 근사적 가격식을 유도하여 직접 가격을 근사하는 방법들의 성능이 좀 더 좋았으며, 그 가운데 비선형 회귀를 이용한 점근적 근사방법이 상대적으로 좋은 성능을 보였다.

• 한국수소및신에너지학회논문집
• /
• 제31권1호
• /
• pp.122-131
• /
• 2020

To reduce emissions from coal-fired power plants, researchers focusing on coal and biomass co-firing technology. Biomass, with its carbon-neutral nature and lower quantities of nitrogen and sulfur compared with coals, has a positive impact on coal-fired power generation. Many studies on the combustion of biomass have been conducted, but the study on the combustion characteristics of biomass char is limited. FERPM predicts char combustion characteristics with high accuracy by introducing experimental data-based parameters of biomass char and has not yet been applied in numerical simulation. In this study, FERPM is numerically applied to char combustion of wood pellets representing wood-based biomass and the combustion characteristics are compared with the kinetic/diffusion limited model, intrinsic model, and diffusion limited model.

• Asian Journal of Atmospheric Environment
• /
• 제12권1호
• /
• pp.47-58
• /
• 2018

The aim of this work is to investigate the effect of atmospheric stability on near-field pollutant dispersion from rooftop emissions of a single cubic building using computational fluid dynamics (CFD). This paper used the shear stress transport (here after SST) k-${\omega}$ model for predicting the flow and pollutant dispersion around an isolated cubic building. CFD simulations were performed with two emission rates and six atmospheric stability conditions. The results of the simulations were compared with the data from wind tunnel experiments and the result of simulations obtained by previous studies in neutral atmospheric condition. The results indicate that the reattachment length on the roof ($X_R$) obtained by computations show good agreement with the experimental results. However, the reattachment length of the rooftop of the building ($X_F$) is greatly overestimated compared to the findings of wind tunnel test. The result also shows that the general distribution of dimensionless concentration given by SST k-${\omega}$ at the side and leeward wall surfaces is similar to that of the experiment. In unstable conditions, the length of the rooftop cavity was decreased. In stable conditions, the horizontal velocity in the lower part around the building was increased and the vertical velocity around the building was decreased. Stratification increased the horizontal cavity length and width near surface and unstable stratification decreased the horizontal cavity length and width near surface. Maintained stability increases the lateral spread of the plume on the leeward surface. The concentration levels close to the ground's surface under stable conditions were higher than under unstable and neutral conditions.

• Asian Journal of Atmospheric Environment
• /
• 제11권3호
• /
• pp.153-164
• /
• 2017

Odor dispersion around a cubic building from rooftop odor emissions was investigated using computational fluid dynamics (CFD). The Shear Stress Transport (here after SST) $k-{\omega}$ model in FLUENT CFD code was used to simulate the flow and odor dispersion around a cubic building. The CFD simulations were performed for three different configurations of cubic buildings comprised of one building, two buildings or three buildings. Five test emission rates were assumed as 1000 OU/s, 2000 OU/s, 3000 OU/s, 4000 OU/s and 5000 OU/s, respectively. Experimental data from wind tunnels obtained by previous studies are used to validate the numerical result of an isolated cubic building. The simulated flow and concentration results of neutral stability condition were compared with the wind tunnel experiments. The profile of streamline velocity and concentration simulation results show a reasonable level of agreement with wind tunnel data. In case of a two-building configuration, the result of emission rate 1000 OU/s illustrates the same plume behavior as a one-building configuration. However, the plume tends to the cover rooftop surface and windward facet of a downstream building as the emission rate increases. In case of a three-building configuration, low emission rates (<4000 OU/s) form a similar plume zone to that of a two-building configuration. However, the addition of a third building, with an emission rate of 5000 OU/s, creates a much greater odorous plume zone on the surface of second building in comparison with a two-building configuration.

• 한국표면공학회지
• /
• 제41권5호
• /
• pp.205-213
• /
• 2008

A 3D particle code is developed to analyze electron behavior in a planar magnetron sputtering cathode either in balanced or unbalanced configuration. Three types of collisions are included; electron - neutral elastic, excitation to a metastable state and ionization. Flight path is calculated by a 4-th order Runge-Kutta method with a time step of 10 ps. Effects of electron starting position, magnetic field intensity and configuration were analyzed. For a more efficient and accurate modeling, multithreading technique is considered for multicore CPU computers. Under an assumption of cold ion approach, target erosion profiles are predicted for a flat target surface.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2008년도 추계학술대회 논문집 전력기술부문
• /
• pp.65-67
• /
• 2008

A new pulse width modulation method based on predictive current control strategy is proposed to modulate matrix converters. The predictive current controller utilizes a discrete-time model to predict the future values of output currents and generates proper duty-ratios ta minimize the output current errors. The proposed method uses continuous carrier and establishes a predictive current controller to predetermine duty ratio signal for directly generating gating signals an thus is named "predictive current control PWM(PCCPWM)". The modulation algorithm nd the required equations are derived by using average concept over one switching period. Thus it can be easily extended to other matrix converter topologies, especially with neutral connections, such as sing le-phase ad two-phase matrix converters. The feasibility and validity of the proposed strategy are verified by computer simulation and experimental results.

• Journal of Power Electronics
• /
• 제10권1호
• /
• pp.91-96
• /
• 2010

In this paper, a simplified control algorithm for a three-phase, four-wire unified power quality conditioner (UPQC) is presented to compensate for supply voltage distortions/unbalance, supply current harmonics, the supply neutral current, the reactive power and the load unbalance as well as to maintain zero voltage regulation (ZVR) at the point of common coupling (PCC). The UPQC is realized by the integration of series and shunt active filters (AFs) sharing a common dc bus capacitor. The shunt AF is realized using a three-phase, four leg voltage source inverter (VSI) and the series AF is realized using a three-phase, three leg VSI. A dynamic model of the UPQC is developed in the MATLAB/SIMULINK environment and the simulation results demonstrating the power quality improvement in the system are presented for different supply and load conditions.

• 공학교육연구
• /
• 제23권2호
• /
• pp.24-30
• /
• 2020

This paper proposes the approaches to the evaluation of learning using concepts of artificial intelligence. Among various techniques, deep learning algorithm is employed to achieve quantitative results of evaluation. In particular, this paper focuses on the process-based evaluation instead of the result-based one using face expression. The expression is simply acquired by digital camera that records face expression when students solve sample test problems. Face expressions are trained using convolutional neural network (CNN) model followed by classification of expression data into three categories, i.e., easy, neutral, difficult. To substantiate the proposed approach, the simulation results show promising results, and this work is expected to open opportunities for intelligent evaluation system in the future.