• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.21 no.8
• /
• pp.44-53
• /
• 2007

In this paper, the Sliding Mode Controller is applied to reduce the starting current of the single phase induction motor. The input voltage to the single phase induction motor is controlled so that the starting current of the motor may be maintained within the rating value and the velocity is also controlled, by adjusting the switching function of the Sliding Mode Controller. The switching of sliding control made appropriately with regard to velocity error signal and acceleration signal. It is shown that the starting characteristics of the single phase induction motor(SPIM) can be greatly enhanced through the sliding control of single phase induction motor.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.27 no.4
• /
• pp.62-72
• /
• 2013

To operate an automatic picking system in distribution center with high precision and high dynamics, this paper presents a robust control scheme of a linear induction motor (LIM) using the mass estimation and disturbance force observer. The force disturbance which gives a direct influence on the control performance of LIM is estimated in real-time through the disturbance observer and compensated by a feedforward manner. To get a satisfactory performance even under the mass variation by reducing the disturbance force due to the mismatched mass during the speed transient such as the acceleration and deceleration periods, a mass estimation algorithm is proposed. A Simulink model for LIM is developed and the validity of the proposed scheme is verified through the comparative simulation studies using Matlab - Simulink.

• Journal of the Korean Institute of Navigation
• /
• v.15 no.1
• /
• pp.49-65
• /
• 1991

It is of great importance for any vessel under way, especially in rough sea, to be maneuvered safely with proper seakeeping performance. In this paper, the author aims to develope a navigational safety evaluation system in rough sea by analyzing ship's with the theory of wave spectrum using random process analysis and the theory of evaluating the seakeeping performance. The scope and the method of this study are as follows ; (1) Modelized typhoon mathematically to represent the sea condition in rough sea. (2) Estimated sea conditions by getting wave spectrum, supposing that the wave by typhoon is fully developed short crest irregular wave. (3) Defined evaluation factor of vessel's seakeeping performance and obtained response amplitude operators thereby. (4) Obtained the response spectrum of factors on seakeeping performance. (5) Defined and obtained evaluation index, dangerousness, relative and maximum dangerousness of factors on seakeeping performance. (6) Analyzed the calculated dangerousness of evaluation index and picked the vertical acceleration out of 7 factors as the presentative factor on seakeeping performance. (7) Carrid out the judgement of danger by obtaining dangerousness value according to steaming hour, course alteration and speed change. By synthesizing the above items, the authors suggests a computer model of navigational safety evaluation system and examined the validity of the model by computer simulation.

• International Journal of Aeronautical and Space Sciences
• /
• v.15 no.2
• /
• pp.163-172
• /
• 2014

This paper proposes a novel guidance law based on the block backstepping sliding mode control and extended state observer (ESO), which also takes into account the autopilot dynamic characteristics of the near space interceptor (NSI), and the impact angle constraint of attacking the maneuvering target. Based on the backstepping control approach, the target maneuvers and the parameter uncertainties of the autopilot are regarded as disturbances of the outer loop and inner loop, respectively. Then, the ESO is constructed to estimate the target acceleration and the inner loop disturbance, and the block backstepping sliding model guidance law is employed, based on the estimated disturbance value. Furthermore, in order to avoid the "explosion of complexity" problem, first-order low-pass filters are also introduced, to obtain differentiations of the virtual control variables. The stability of the closed-loop guidance system is also proven, based on the Lyapunov theory. Finally, simulation results demonstrate that the proposed guidance law can not only overcome the influence of the autopilot dynamic delay and target maneuvers, but also obtain a small miss distance.

• International Journal of Control, Automation, and Systems
• /
• v.4 no.4
• /
• pp.405-413
• /
• 2006

A novel approach based on genetic algorithms (GA) is developed to find a global minimum-jerk trajectory of a space robotic manipulator in joint space. The jerk, the third derivative of position of desired joint trajectory, adversely affects the efficiency of the control algorithms and stabilization of whole space robot system and therefore should be minimized. On the other hand, the importance of minimizing the jerk is to reduce the vibrations of manipulator. In this formulation, a global genetic-approach determines the trajectory by minimizing the maximum jerk in joint space. The planning procedure is performed with respect to all constraints, such as joint angle constraints, joint velocity constraints, joint angular acceleration and torque constraints, and so on. We use an genetic algorithm to search the optimal joint inter-knot parameters in order to realize the minimum jerk. These joint inter-knot parameters mainly include joint angle and joint angular velocities. The simulation result shows that GA-based minimum-jerk trajectory planning method has satisfactory performance and real significance in engineering.

• 제어로봇시스템학회:학술대회논문집
• /
• 2005.06a
• /
• pp.2126-2131
• /
• 2005

Interactions of a humanoid with a human are important, when the humanoid is requested to provide people with human-friendly services in unknown or uncertain environment. Such interactions may require more complicated and human-like behaviors from the humanoid. In this work the arm motions of a human are discussed as the early stage of human motion imitation by a humanoid. A motion capture system is used to obtain human-friendly arm motions as references. However the captured motions may not be applied directly to the humanoid, since the differences in geometric or dynamics aspects as length, mass, degrees of freedom, and kinematics and dynamics capabilities exist between the humanoid and the human. To overcome this difficulty a method to adapt captured motions to a humanoid is developed. The geometric difference in the arm length is resolved by scaling the arm length of the humanoid with a constant. Using the scaled geometry of the humanoid the imitation of actor's arm motions is achieved by solving an inverse kinematics problem formulated using optimization. The errors between the captured trajectories of actor arms and the approximated trajectories of humanoid arms are minimized. Such dynamics capabilities of the joint motors as limits of joint position, velocity and acceleration are also imposed on the optimization problem. Two motions of one hand waiving and performing a statement in sign language are imitated by a humanoid through dynamics simulation.

• IEMEK Journal of Embedded Systems and Applications
• /
• v.5 no.4
• /
• pp.243-253
• /
• 2010

Multihop data delivery in vehicular ad hoc networks (VANETs) suffers from the fact that vehicles are highly mobile and inter-vehicle links are frequently disconnected. In such networks, for efficient multihop routing of road safety information (e.g. road accident and emergency message) to the area of interest, reliable communication and fast delivery with minimum delay are mandatory. In this paper, we propose a multihop vehicle-to-infrastructure routing protocol named Vertex-Based Predictive Greedy Routing (VPGR), which predicts a sequence of valid vertices (or junctions) from a source vehicle to fixed infrastructure (or a roadside unit) in the area of interest and, then, forwards data to the fixed infrastructure through the sequence of vertices in urban environments. The well known predictive directional greedy routing mechanism is used for data forwarding phase in VPGR. The proposed VPGR leverages the geographic position, velocity, direction and acceleration of vehicles for both the calculation of a sequence of valid vertices and the predictive directional greedy routing. Simulation results show significant performance improvement compared to conventional routing protocols in terms of packet delivery ratio, end-to-end delay and routing overhead.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.27 no.10
• /
• pp.53-59
• /
• 1990

In the control of robot manipulators, this paper presents a design of a new variable structure model following controller(VSMFC) using computed torque method (CTM). A sufficient condition for the existence of a sliding mode is derived by Lyapunov function. The reference model is a double integrators and the acceleration input consists of a proportional-derivative controller for the purpose of the stabilization of system and the desired performance. The proposed control scheme which consists of upper bounded and estimated value of each term of the manipulator of matrix inversion. Therefore the simulation results show that this controller is improved to the convergence of desired trajectories.

• Journal of the Korean Society for Precision Engineering
• /
• v.26 no.1
• /
• pp.138-145
• /
• 2009

High-efficiency and high-quality machining has become a fact of life for numerous machine shops in recent years. And high-efficiency machining is the most significant tool to enhance productivity. In this study, to achieve high-efficiency machining in turning process, a spindle speed optimization method was proposed based on a cutting power model. The cutting force and power were estimated from the cutting parameters such as specific cutting force, feed, depth of cut, and spindle speed. The time delay due to the acceleration or deceleration of spindle was considered to predict a more accurate machining time. Especially, the good agreement between the predicted and measured cutting forces showed the reliability of the proposed optimization method, and the effectiveness of the proposed optimization method was demonstrated through the simulation results associated with the productivity enhancement in turning process

• KOREAN JOURNAL OF PACKAGING SCIENCE & TECHNOLOGY
• /
• v.23 no.2
• /
• pp.103-108
• /
• 2017

The amount of delivered parcels have been increasing according to the change and expansion of consumption pattern through e-commerce, and they are required to minimize breakout or failure under the delivery. In this study, we measured and analyzed the distribution environment data (vibration and impact) occurred in the packaging, which were prepared with 5 types by the weight and dimension, distributed from Seoul to Busan in Korea by 2 parcel delivery service companies through e-commerce order. Date showed the parcels had 3-5 times of drop impact and 0.3-0.7 m of drop height on average, and 0.8 Grms of vibration acceleration from equivalent equation to the vertical direction. The significant gap in service quality was not found between 2 parcel delivery service companies. This study is expected to be useful for designing the suitable packaging in order to enhance safe transportation of the delivered packaging, and furthermore useful for developing Korean testing method for Field-to-Lab simulation.