• Journal of the Korean Ceramic Society
• /
• v.47 no.2
• /
• pp.127-131
• /
• 2010

Biomimetic whisker-like apatite was formed on thermally and NaOH-treated titanium powder in a simulated body fluid (SBF). In the early process of the SBF immersion, the surface structure of the titanium powder was loosened, possibly due to the dissolution of $Na^+$ ions on the surface of the titanium powder into SBF. When immersed for 7 days in SBF, fine precipitates appeared on the titanium surfaces; the coating layer (<200 nm in thickness) consisted of nanostructured, amorphous whisker-like and particulate phase, observed by TEM. With the extension of the immersion time to 16 days, the chrysanthemum flower type morphology of carbonated hydroxyapatite with a nanocrystallinity was developed on the surface of the titanium powder.

• Bulletin of the Korean Chemical Society
• /
• v.35 no.10
• /
• pp.2935-2940
• /
• 2014

Monodispersed $Bi_2O_2CO_3$ nanoplates with an average width of 320 nm and thicknesses of 50-90 nm were successfully synthesized by a simple solvothermal method in a mixture solution of polyethylene glycol and $H_2O$. The obtained nanoplates were characterized by means of XRD, FT-IR, SEM and TEM. The effect of surfactant sodium dodecyl benzene sulfonate on the morphology of $Bi_2O_2CO_3$ product was investigated. Under simulated solar light irradiation, $Bi_2O_2CO_3$ nanoplates exhibited superior photocatalytic activities towards the degradation of RhB as well as high chemical stability upon cycling photocatalytic test. The nanoplates also showed promising photodegradation ability for eliminating refractory pollutant of phenol. The excellent photocatalytic performance of $Bi_2O_2CO_3$ nanoplates as compared with P25-$TiO_2$ endows them as promising high efficiency photocatalysts.

• International journal of advanced smart convergence
• /
• v.11 no.4
• /
• pp.88-95
• /
• 2022

Vacuum simulation is associated with the prediction and calculation of how materials, pumps and systems will perform using mathematical equations. In this investigation, three different high vacuum systems were simulated and estimated with each vacuum characteristics by VacTran simulator. In each of modelled vacuum systems, selection of gas loads into vessel, combination of rough and high vacuum pumps and dimension of conductance elements were proposed as system variables. In pump station model, the pumping speed to pressures by the combination of root pump was analyzed under the variations of vessel volume. In this study, the effects of outgassing dependent on vessel materials was also simulated and aluminum vessel was estimated to optimum materials. It was obtained from the modelling with diffusion pump that the diameter, length of 50×250[mm]roughing line was characterized as optimum variables to reach the ultimate pressure of 10E-7[torr]. Optimum design factors for vacuum characteristics of modelled vacuum system were achieved by VacTran simulator. Feasibility of VacTran as vacuum simulator was verified and applications of VacTran in high tech process expected to be increased.

• Proceedings of the KACD Conference
• /
• 2003.11a
• /
• pp.595-595
• /
• 2003

I. Objectives This study was done to evaluate which type of Ni-Ti instrument be able to perform canal shape well in the simulated canal with abrupt curvature near it's apex. II. Materials and Methods A total of 96 simulated root canals were made in epoxy resin(EPOXICURETM, BUEHLER, USA), ＃15 finger spreader (MANI, Japan) were used as root canal templates. The simulated root canal were made with radius of curvature of 1.5 mm, 3.0 mm, 4.0 mm, 6.0 mm respectively, and angle of curvature of all simulate camals was 90 degree.(omitted)

• Proceedings of the KACD Conference
• /
• 2003.11a
• /
• pp.554-554
• /
• 2003

I. Objectives This study was done to evaluate the shaping ability of ProFile and ProTaper, K-Flexofile during instrumentation in simulated resin canals with different angles of curvature. II. Materials and Methods Ninety simulated root canals with a curvature of 15, 30 and 45 degree (following Schneider's method) were made of epoxy resin ($EPOXICURE^{TM}$, BUEHLER, USA) for this study. The canal length of simulated root canals was adjusted to 18 mm. The beginning point of curvature was positioned at 10mm from the canal orifice.(omitted)

• Nuclear Engineering and Technology
• /
• v.30 no.1
• /
• pp.1-7
• /
• 1998

Effects of pH, bentonite and Portland cement on the leaching of the simulated waste glass were investigated. The simulated waste glass showed the low leach rate in the neutral pH region, while the leach rate in both acidic and alkaline regions increased. Addition of bentonite to the leachant enhanced the leaching of the waste glass. When the waste glass was leached at 72$^{\circ}C$ for 36 days in the ground water with gel state Na-bentonite, approximately 2.2${\mu}{\textrm}{m}$ of the surface was corroded out and the large amount of Ti, Nd, and Zr was observed on the surface. The amount of B leached from the simulated waste glass in the presence of domestic bentonite was about three times higher than that in the presence of Aldrich bentonite as well as Portland cement.

• Journal of the Korean institute of surface engineering
• /
• v.41 no.5
• /
• pp.226-231
• /
• 2008

Titanium and its alloy have been widely used in dental implant and orthopedic prostheses. Electrochemical characteristics of dental implant in the various simulated body fluids have been researched by using electrochemical methods. Ti-6Al-4V alloy implant was used for corrosion test in 0.9% NaCl, artificial saliva and simulated body fluids. The surface morphology was observed using scanning electron microscopy (SEM) and energy dispersive x-ray spectroscopy (EDX). The electrochemical stability was investigated using potentiosat (EG&G Co, 263A). The corrosion surface was observed using scanning electron microscopy (SEM). From the results of potentiodynamic test in various solution, the current density of implant tested in SBF and AS solution was lower than that of implant tested in 0.9% NaCl solution. From the results of passive film stability test, the variation of current density at constant 250 mV showed the consistent with time in the case of implant tested in SBF and AS solution, whereas, the current density at constant 250mV in the case of implant tested in 0.9% NaCl solution showed higher compared to SBF and AS solution as time increased. From the results of cyclic potentiodynamic test, the pitting potential and |$E_{pit}\;-\;E_{corr}$| of implant tested in SBF and AS solution were higher than those of implant tested in 0.9% NaCl solution.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2005.05a
• /
• pp.189-189
• /
• 2005

• Journal of Welding and Joining
• /
• v.35 no.1
• /
• pp.9-15
• /
• 2017

IMicrostructure evolution and tensile property in the weld heat-affected zone (HAZ) of austenitic Fe-30Mn-9Al-0.9C lightweight steels were investigated. Five alloys with different V and Nb content were prepared by vacuum induction melting and hot rolling process. The HAZ samples were simulated by a Gleeble simulator with welding condition of 300kJ/cm heat input and HAZ peak temperatures of $1150^{\circ}C$ and $1250^{\circ}C$. Microstructures of base steels and HAZ samples were observed by scanning electron microscopy (SEM) and transmission electron microscopy (TEM), and their mechanical properties were evaluated by tensile tests. The addition of V and Nb formed fine V and/or Nb-rich carbides, and these carbides increased tensile and yield strength of base steels by grain refinement and precipitation hardening. During thermal cycle for HAZ simulation, the grain growth occurred and the ordered carbide (${\kappa}-carbide$) formed in the HAZs. The yield strength of HAZ samples (HAZ 1) simulated in $1150^{\circ}C$ peak temperature was higher as compared to the base steel due to the formation of ${\kappa}-carbide$, while the yield strength of the HAZ samples (HAZ 2) simulated in $1250^{\circ}C$ decreased as compared to HAZ 1 due to the excessive grain growth.

• Nuclear Engineering and Technology
• /
• v.51 no.1
• /
• pp.207-213
• /
• 2019

Corrosion and mechanical behavior of the hot-rolled 0.5%Gd-0.8%B-stainless steel to develop a spent nuclear fuel storage material was studied in a simulated nuclear waste treatment condition with rolling condition. The austenite and ferrite phases of the 0.5%Gd-0.8%B-stainless steels are about 88:12. The average austenite and ferrite grain size of the plane normal to rolling, transverse and normal directions of the hot rolled specimens are about 5.08, 8.94, 19.35, 23.29, 26.00 and 18.11 [${\mu}m$], respectively. The average micro-hardness of the as-cast specimen is 200.4 Hv, whereas, that of the hot-rolled specimen are 220.1, 204.7 and 203.5 [$H_v$] for the plane normal to RD, TD and ND, respectively. The UTS, YS and elongation of the as-cast and the hot-rolled specimen are 699, 484 [MPa], 34.0%, and 654, 432 [MPa] and 33.3%, respectively. The passivity was observed both for the as-cast and the hot rolled specimens in a simulated nuclear waste solution. The corrosion potential and corrosion rate of the as-casted specimens are $-343[mV_{SHE}]$ and $3.26{\times}10^{-7}[A/cm^2]$, whereas, those of the hot rolled specimens with normal to ND, RD and TD are -630, -512 and -620 [$mV_{SHE}$] and $6.12{\times}10^{-7}$, $1.04{\times}10^{-6}$ and $6.92{\times}10^{-7}[A/cm^2]$, respectively. Corrosion tends to occur preferentially Cr and B rich area.