• Journal of the Society of Naval Architects of Korea
• /
• v.49 no.6
• /
• pp.534-540
• /
• 2012

The global performance of various ships estimated by simplified formulae of classification societies is compared with the numerical results by a strip-theory-based whipping analysis program including slamming impact(USLAM). Heave acceleration, pitch angle and the vertical acceleration are compared and the effectiveness of simplified formulae is evaluated. Four different ship models are used for comparison study, which include S175, Flokstra, 6000TEU and 8100TEU container ships. In order to verify the numerical results, the vertical bending moment of S175 is compared with the results of ITTC workshop data.

• Journal of Ocean Engineering and Technology
• /
• v.27 no.1
• /
• pp.80-84
• /
• 2013

This study is to develop the simplified formulae for added mass coefficient of a 2-D floating body with a semi-circle section in a finite water depth. The semi-circle floating body may represent a simplified midship section transformed by Lewis form, which can be used for the ship motion analysis by strip theory. Since the added mass coefficient varies with motion frequencies and sea bottom effect, the correction factor representing the effect of water depth and frequencies is developed for accurate prediction of added mass. Using a two-dimensional numerical wave tank (NWT) technique based on the boundary element method (BEM) including sea bottom boundary the reference values of added mass are calculated to develop the correction factor. For verification and effectiveness of the formulae, the predicted added mass coefficients for various frequencies and water depth ratios are compared with the calculated values from NWT technique.

• Structural Engineering and Mechanics
• /
• v.28 no.2
• /
• pp.189-206
• /
• 2008

In several design codes and specifications, simplified formulae and charts are given for determining the effective lengths of frame columns. It is shown that these formulae may yield rather erroneous results in certain cases. This is due to the fact that, the code formulae utilise only local stiffness distributions. In this paper, a simplified procedure for determining approximate values for the buckling loads of braced frames is developed. The procedure utilises a fictitious load analysis of frames and yields errors less than 10%, which may be considered suitable for design purposes. The proposed procedure is applied to several numerical examples and it is shown that all the errors are in the acceptable range.

• Structural Engineering and Mechanics
• /
• v.19 no.1
• /
• pp.55-71
• /
• 2005

In several design codes and specifications, simplified formulae and diagrams are given for determining the buckling lengths of frame columns. It is shown that these formulae may yield rather erroneous results in certain cases. This is due to the fact that, the code formulae utilise only local stiffness distributions. In this paper, a simplified procedure for determining approximate values for the buckling loads of multi-storey frames is developed. The procedure utilises lateral load analysis of frames and yields errors in the order of 10%, which may be considered suitable for design purposes. The proposed procedure is applied to several numerical examples and it is shown that all the errors are in the acceptable range and on the safe side.

• Steel and Composite Structures
• /
• v.29 no.1
• /
• pp.125-138
• /
• 2018

The research on the confinement behavior of ultra high performance concrete without and with the use of steel fibers (UHPC and UHPFRC) has been extremely limited. In previous studies, authors experimentally investigated the axially compressive behavior of circular steel tube confined concrete (STCC) short and intermediate columns with the employment of UHPC and UHPFRC. Under loading on only the concrete core, the confinement effect induced by the steel tube was shown to significantly enhance the utimate stress and its corresponding strain of the concrete core. Therefore, this paper develops a simplified stress - strain model for circular STCC columns using UHPC and UHPFRC with compressive strength ranging between 150 MPa and 200 MPa. Based on the regression analysis of previous test results, formulae for predicting peak confined stress and its corresponding strain are proposed. These proposed formulae are subsequently compared against some previous empirical formulae available in the literature to assess their accuracy. Finally, the simplified stress - strain model is verified by comparison with the test results.

• Proceedings of the Korean Magnestics Society Conference
• /
• 1996.10a
• /
• pp.102-103
• /
• 1996

• Journal of the Korean Geotechnical Society
• /
• v.16 no.1
• /
• pp.19-30
• /
• 2000

The major design parameters of the anchored sheet-pile wall include the determination of required penetration depth, the force acting on the anchor, and the maximum bending moment in the piling. Blum solved the fixed earth supported wall using the equivalent beam method, assuming that the wall can be separated into upper and lower parts of the point of contraflexure. Design charts help designer by simplifying the design procedure. But they have some difficulties under some Geotechnical and geometrical conditions. For example, the conventional design charts can compute design parameters only when the ground water table exists above the dredge line. In this paper, the design charts which can be used for the ground water table existing under the dredge line are presented. And simplified formulae are developed by regression analysis. It is found that simplified formulae are not only very useful for the practice of design but also they can evaluate the result of numerical methods or design charts.

• Proceedings of the KIEE Conference
• /
• 1999.07c
• /
• pp.1236-1238
• /
• 1999

This paper presents an effect of cross magnetization to the generator simplified linear model which is used for multi-machine power systems. The formulae of reactances and time constant with saturation effect are presented. The simulation results show that cross magnetization has an effect which can not be ignored, to the reactances, time constant and eigenvalues in one machine infinite bus system of simplified linear model.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2011.04a
• /
• pp.544-549
• /
• 2011

Simplified formulae for axial and bending natural frequencies of bellows are developed using an equivalent thin-walled pipe model. The axial and bending stiffness of bellows is determined using lumped transfer matrix method. Accordingly, the Expansion Joint Manufacturers Association (EJMA) formula for axial and bending stiffness calculation is modified using two different equivalent radii. The results from the simplified formulae are verified by those from a experiment result and a finite element (FE) model and good agreement is shown between the each other.

• Proceedings of the Korean Magnestics Society Conference
• /
• 1996.10a
• /
• pp.104-105
• /
• 1996