• Journal of Korean Society on Water Environment
• /
• v.29 no.4
• /
• pp.466-475
• /
• 2013

Non-point source pollution management is one of the most important issues in Korean water quality/watershed management. In recent years, Low Impact Development (LID) has emerged as an effective approach to control stormwater in an urban area. This study illustrates how to design and evaluate the effect of non-point pollutant management using EPA-SWMM LID module and suggests design parameters for modeling LID facilities. In addition, optimal installation locations of LID can be determined by a simple distributed hydrologic model by using SWMM for a long-term.

• Journal of Power Electronics
• /
• v.9 no.6
• /
• pp.835-844
• /
• 2009

In this paper a new buck-boost type DC-DC converter is presented. Its voltage gain is positive, all active elements operate under soft-switching condition independent of loading, magnetic isolation and self output short-circuit protection exist, and very fast dynamic operation is achievable by a simple bang-bang controller. This converter also exhibits appropriate PFC characteristics since its input current is inherently proportional to the source voltage. When the voltage source is off-line, it is sufficient to add an inductor after the rectifier, then near unity power factor is achievable. All essential guidelines to design the converter as a DC-DC and a PFC regulator are presented. Simulation and experimental results verify the developed theoretical analysis.

• Journal of the Korean Society for Precision Engineering
• /
• v.21 no.4
• /
• pp.79-87
• /
• 2004

The light pattern reflected from a machined surface contains some information like roughness and profile on the projected surface as expected in the Beckmann-Spizzichino model. In applying the theory into a real reliable measuring device, many parameters such as incident light power, wave length, spot size should be kept a constant optical value. However, the reflected light power is likely to change with the environmental noise, the variations of the light source, the reflectivity of the surface, etc. even though the incident light power is constant. In this study, a method for adjusting the incident light power to keep the reflected light power projected on a CMOS image sensor constant was proposed and a simple adjustment algorithm based on PI digital control was examined. Experiments verified that the proposed method made the surface roughness measurement better and more reliable even under variations of the height of light source.

• Structural Engineering and Mechanics
• /
• v.46 no.3
• /
• pp.371-385
• /
• 2013

Vibration isolators and anti-vibration mounts are ideal, for example, in creating floating floors for gymnasiums, or performance spaces. However, it is well-known that there are great difficulties on isolating vibration transmission in structural steel components, especially steel floors. Besides, the selection of inertia blocks, which are usually used by engineers as an effective vibration control measure, is usually based on crude methods or the experience of the engineers. Thus, no simple method or indices have been available for assessing the effect of inertia blocks on vibration isolation or stability of vibratory systems. Thus, the aims of this research are to provide further background description using a FE model and present and implement a modal approach, that was validated experimentally, the latter assisting in providing improved understanding of the vibration transmission phenomenon in steel buildings excited by a velocity-source type of excitation. A better visualization of the mean-square velocity distribution in the frequency domain is presented using the concept of modal expansion. Finally, the variation of the mean-square velocity with frequency, whilst varying mass and/or stiffness of the coupled system, is presented.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.2 no.2
• /
• pp.59-72
• /
• 1994

For a panel contribution of the passenger vehicle compartment, a model was created for acoustic analysis of the passenger vehicle compartment and through the acoustic normal modal analysis, frequencies and mode shapes of the resonance modes were calculated. Also, the contribution analysis of each panel was executed using acoustic reciprocal theorem, and through this analysis, normalized responses at the particular point indicate the relative contribution of each panel for generating noise and vibration

• Journal of Korea Multimedia Society
• /
• v.8 no.6
• /
• pp.744-752
• /
• 2005

When the multiple video sources are transmitted together through the channel of fixed bandwidth, an efficient picture quality control is necessary. This paper presents a joint picture quality control method to satisfy the user requirement by priority among the video sources. The better picture quality is assigned to the source of higher priority compared to lower priority. We obtain the bitrate for each source to have a required distortion level among the sources by using an approximate distortion-bitrate model for simple implementation. It is shown by simulation that the proposed bandwidth allocation method can keep almost the user-required picture quality among the sources in comparison to an independent bandwidth allocation method.

• Proceedings of the KIPE Conference
• /
• 2008.06a
• /
• pp.24-27
• /
• 2008

For high voltage DC-DC converters, the parallel operation of several high voltage source modules is necessary to reduce the material cost. In the conventional parallel operation with HDC module control unit, it is difficult to repair the HDC system for the failure of control unit. To overcome these problems, new parallel operating algorithm for high voltage DC-DC converter is presented. The proposed algorithm has no main control unit and each module can be selected as the master according to the operating conditions. Therefore, one of modules can be replaced as the master immediately when the previous master module is failed. In addition, the extension of extra modules can be simple.

• Proceedings of the KIEE Conference
• /
• 2006.11a
• /
• pp.234-236
• /
• 2006

In this paper, APF(Active Power Filter) will be treated in order to improve the output current distortion of the AC source. APF generates the harmonic current which contributes to a source side harmonic reduction. We can extract the compensating current of the parallel APF with phase transformations and the proposed current control method. Therefore, the calculation times is short and the control method is simple compared with conventional hysteresis methods. Experimental results verify that the system using the proposed method appers a good performance.

• Proceedings of the KIPE Conference
• /
• 2014.11a
• /
• pp.66-67
• /
• 2014

Stabilization of the DC bus voltage is an important task in DC-AC microgrid system with renewable energy source such as solar system. A battery energy storage system (BESS) has become a general solution to stabilize the DC-bus voltage in DC-AC microgrid. This paper develops the analog BESS controller which requires neither computation nor dc-bus voltage measurement, so that the system can be implemented simply and easily. Even though others methods can stabilize and control the DC-bus voltage, it has complicated structure in control and low adaptive capability. The proposed topology is simple but is able to compensate the solar source variation and stabilize the DC-bus voltage under any loads and distributed generation (DG) conditions. In addition, the design of analog controller is presented to obtain a robust system. In order to verify the effectiveness of the proposed control strategy, simulation is carried out by using PSIM software.

• Proceedings of the KIPE Conference
• /
• 2014.11a
• /
• pp.25-26
• /
• 2014

Renewable energy sources such as wind and solar power are free and can be easily harvested everywhere. However, one of the biggest problems when using this kind of energy source is how to increase the efficiency of power conversion system. This paper introduces a modified 3-phase inverter in order to increase the power conversion efficiency. By adding 3 bi-directional switches at output of the inverter, the current flow back DC source during zero state is prevented to minimize leakage current, so that the efficiency of whole system is increased. The proposed topology also improves the power quality to satisfy the total harmonics distortion (THD) requirement. In order to verify the effectiveness of the proposed topology, simulation results are carried out using Simulink in MATLAB.