• 반도체디스플레이기술학회지
• /
• 제2권2호
• /
• pp.9-15
• /
• 2003

This paper proposes a thickness measurement method of silicon-oxide and poly-silicon film deposited on 12" silicon wafer for spin etcher. Halogen lamp is used as a light source for generating a wide-band spectrum, which is guided and focused on the wafer surface through a optical fiber cable. Interference signal from the film is detected by optical sensor to determine the thickness of the film using spectrum analysis and several signal processing techniques including curve-fitting and adaptive filtering. Test wafers with three kinds of priori-known films, polysilicon(300 nm), silicon-oxide(500 nm) and silicon-oxide(600 nm), are measured while the wafer is spinning at 20 Hz and DI water flowing on the wafer surface. From experiment results the algorithm presented in the paper is proved to be effective with accuracy of maximum 0.8% error.rror.

• 한국전기전자재료학회논문지
• /
• 제29권10호
• /
• pp.595-600
• /
• 2016

In this paper, the oxide currents of thin silicon oxides is investigated. The oxide currents associated with the on time of applied voltage were used to measure the distribution of voltage stress induced traps in thin silicon oxide films. The stress induced leakage currents were due to the charging and discharging of traps generated by stress voltage in the silicon oxides. The stress induced leakage current will affect data retention in memory devices. The oxide current for the thickness dependence of stress current and stress induced leakage currents has been measured in oxides with thicknesses between $109{\AA}$, $190{\AA}$, $387{\AA}$, and $818{\AA}$ which have the gate area $10^{-3}cm^2$. The oxide currents will affect data retention and the stress current, stress induced leakage current is used to estimate to fundamental limitations on oxide thicknesses.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2011년도 제41회 하계 정기 학술대회 초록집
• /
• pp.343-343
• /
• 2011

저온에서의 Thin Film Transistor (TFT) 혹은 Nonvolatile memory (NVM) 등의 MOS 구조 소자들의 높은 전기적 특성에 관한 연구들이 진행 되면서 mobility와 stability 그리고 구조화의 용이성에 대한 연구가 진행됨에 따라 amorphous silicon의 결정화를 통해 전기적 특성을 향상 시킨 Nanocrystalline silicon (nc-Si)/Microcrystalline silicon (${\mu}c$-Si)에 대한 연구가 관심을 받고 있다. 본 논문에서는 ${\leq}300^{\circ}C$에서 Inductively coupled plasma chemical vapor deposition를 이용한 TFT을 제작하였다. 가스비, 온도, 두께에 따른 결정화 정도를 Raman spectra를 통해 확인한 후 Bottom gate와 Top gate 구조의 TFT를 제작 하고 결정화에 따른 전기적 특성 향상과 그의 덧붙여 플라즈마 처리를 통한 특성 향상을 확인 하였다.

• 반도체디스플레이기술학회지
• /
• 제16권2호
• /
• pp.39-43
• /
• 2017

It was confirmed that the silicon thin films fabricated on the p-Si (100) substrates by using DIPAS (DiIsoPropylAminoSilane) and TDMA-Sb (Tris-DiMethylAminoAntimony) sources by RPCVD method were amorphous and n-type silicon. The fabricated amorphous n-type silicon films had electron carrier concentrations and electron mobilities ranged from $6.83{\times}10^{18}cm^{-3}$ to $1.27{\times}10^{19}cm^{-3}$ and from 62 to $89cm^2/V{\cdot}s$, respectively. The ideality factor of the pn junction diode fabricated on the p-Si (100) substrate was about 1.19 and the efficiency of the fabricated pn solar cell was 10.87%.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2010년도 추계학술대회 초록집
• /
• pp.56.1-56.1
• /
• 2010

결정질 실리콘 태양전지의 표면 ARC(Anti-reflection Coating)layer는 반사도를 줄여 광 흡수율을 증가시키고, passivation 효과를 통하여 표면 재결합을 감소 시켜 태양전지의 효율을 높이는 중요한 역할을 한다. Silicon nitride 박막은 외부 stress 요인에 대해 안정성을 담보할 수 있어야한다. 따라서, 본 연구에서는 굴절률 가변에 따른 silicon nitride 박막을 PECVD를 이용하여 증착하고, 항온/항습 stability test를 통해 박막의 안정성을 확인하였다. Silicon nitride 증착을 위해 PECVD를 이용하였고, 공정압력 0.8Torr, 증착온도 $450^{\circ}C$, 증착파워 300W에서 실험을 진행하였다 박막의 굴절률은 1.9~2.3의 범위로 가변하였다. 항온/항습에 대한 신뢰성을 test 하기 위하여 5시간동안의 test를 1cycle로 하여 20회 동안 실험을 실시하였다. 증착된 silicon nitride 박막의 lifetime은 firing 이후 57.8us로 가장 높았으며, 항온/항습 test 이후에도 유사한 경향을 확인 할 수 있었다. 또한, 100h 동안의 항온/항습 test 결과 silicon nitride 박막의 lifetme 감소는 8.5%에 불과했다. 본 연구를 통하여 온도와 습도의 변화에 따른 결정질 실리콘 태양전지의 SiNx 박막의 증착 공정 조건에 대한 신뢰성을 확인 할 수 있었다.

• 대한전자공학회논문지SD
• /
• 제38권11호
• /
• pp.781-790
• /
• 2001

실리콘 웨이퍼 두께에 따른 PZT 박막 적외선 감지소자의 성능변화를 이론적 해석 및 실험적 검증을 통하여 분석하였다. 실리콘이 모두 식각되었을 때 최대값을 보이는 전류응답도는 소자의 뒷면에 남아있는 실리콘의 두께가 50㎛로 두꺼워질 때까지 기하급수적으로 줄어들다가, 그 이상의 두께에서는 전류응답도의 감소폭이 현저히 줄어들었다. 실리콘이 모두 식각된 적외선 감지소자는 450㎛두께의 실리콘이 남아있는 소자에 비해 100배 이상의 높은 전류응답도를 보였다. 이러한 이론적인 해석을 검증하기 위하여 실리콘 기판미세가공법을 이용하여 세 가지 다른 실리콘 두께를 가진 적외선 감지소자를 제작하였다. 제작한 소자에서 측정한 전류응답도의 변화는 이론적 해석값과 좋은 일치를 보였다. 한편, 실험을 통하여 실리콘 두께가 소자의 전류응답도 뿐만 아니라 응답속도에도 큰 영향을 준다는 것을 확인하였다.

• 반도체디스플레이기술학회지
• /
• 제3권2호
• /
• pp.17-21
• /
• 2004

Aluminum nitride(AlN) thin films were deposited on silicon substrate by reactive RF magnetron sputtering without substrate heating. We investigated the dependence of some properties for AlN thin film on sputtering conditions such as working pressure, $N_2$ concentration and RF power. XRD, Ellipsometer and AES has been measured to find out structural properties and preferred orientation of AlN thin films. Deposition rate of AlN thin film was increased with an increase of RF power and decreased with an increase of $N_2$ concentration. AES in-depth measurements showed that stoichiometry of Aluminium and Nitrogen elements were not affected by $N_2$ concentration. It has shown that low working pressure, low $N_2$ concentration and high RF power should be maintained to deposit AlN thin film with a high degree of (0002) preferred orientation.

• Applied Microscopy
• /
• 제45권4호
• /
• pp.195-198
• /
• 2015

Gas-assisted etching (GAE) with focused ion beam (FIB) was applied to prepare plan-view specimens of Cu thin-layer on a silicon substrate for transmission electron microscopy (TEM). GAE using $XeF_2$ gas selectively etched the silicon substrate without volume loss of the Cu thin-layer. The plan-view specimen of the Cu thin film prepared by FIB milling with GAE was observed by scanning electron microscopy and $C_S$-corrected high-resolution TEM to estimate the size and microstructure of the TEM specimen. The GAE with FIB technique overcame various artifacts of conventional FIB milling technique such as bending, shrinking and non-uniform thickness of the TEM specimens. The Cu thin film was uniform in thickness and relatively larger in size despite of the thickness of <200 nm.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2003년도 하계종합학술대회 논문집 II
• /
• pp.1085-1088
• /
• 2003

In this work, we fabricated a gas-sensing device based on porous silicon(PS), and its I-V and C-V properties were investigated for sensing alcohol vapor. The structure of the sensor consists of thin Au/Oxidized porous silicon/porous silicon/Silicon/Al, where the silicon substrate is etched anisotropically to be prepared into a membrane shape. As the result, I-V curves showed typical tunneling property, and C-V curves were shaped like those of a MIS (metal-insulator- semiconductor) capacitor, where the capacitance in accumulation was increased with alcohol vapor concentration.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2015년도 제49회 하계 정기학술대회 초록집
• /
• pp.257.2-257.2
• /
• 2015

In this paper, we report on the 10.33% efficient thin film/bulk tandem solar cells with the top cell made of amorphous silicon thin film and p-type bulk crystalline silicon bottom cell. The tunneling junction layers were used the doped nanocrystalline Si layers. It has to allow an ohmic and low resistive connection. For player and n-layer, crystalline volume fraction is ~86%, ~88% and dark conductivity is $3.28{\times}10-2S/cm$, $3.03{\times}10-1S/cm$, respectively. Optimization of the tunneling junction results in fill factor of 66.16 % and open circuit voltage of 1.39 V. The open circuit voltage was closed to the sum of those of the sub-cells. This tandem structure could enable the effective development of a new concept of high-efficiency and low cost cells.