• 한국재료학회지
• /
• 제3권4호
• /
• pp.381-387
• /
• 1993

${Si_3}{N_4}$와 BN의 선택적 산화반응과 질소분위기 소결에 의하여 $Si_2N_2O$로 결합된$Si_3N_4-BN$복합재료를 개발하였으며, 이때 산화반응 온도와 CaO의 첨가가 $Si_2N_2O$의 생성에 미치는 영향을 고찰하였다. $Si_2N_2O$상이 도입된 $Si_3N_4-BN$복합재료는 내열충격성 및 용강에 대한 내침식성이 우수하여 연속제강새안의 부품인 break ring등의 소재로 사용될 수 있다.

• 전기학회논문지P
• /
• 제58권2호
• /
• pp.190-195
• /
• 2009

Thin-gauged 3% silicon steel sheets having a highly grain-oriented texture have been developed as a core material for applications of middle-frequency (400 Hz ${\sim}$ 10 kHz) devices. The newly developed sheets with a tension coating showed an excellent reduction in iron loss at 400 Hz (iron loss at 1.0 T and 400 Hz = 4.677 W/kg, iron loss at 1.5 T and 400 Hz = 9.742 W/kg) due to high magnetic induction, $B_{10}$(measured induction at 1000 A/m), of over 1.9 T. In cases of frequencies below 400 Hz, magnetic induction, $B_{10}$, of the sample plays a major role to reduce its iron loss as excitation induction increases, whereas, in case of frequency of 1 kHz, thickness dependence becomes dominant due to a lower iron loss at relatively thinner sample. The sheets with a high magnetic induction, therefore, are favorable for high excitation induction (over 1.0 T) and low excitation frequency (below 400 Hz) applications, whereas the sheets that can reduce eddy current loss by reducing thickness or domain wall width are advantageous for low excitation induction (below 1.0 T) and high excitation frequency (around 1 kHz) applications.

• 대한기계학회논문집
• /
• 제18권10호
• /
• pp.2597-2605
• /
• 1994

The wear behavior of two types of $Si_3N_4$ exposed to high and low humidity was examined at various sliding speeds, using bearing steel as disk material under pin-on-disk type sliding conditions. Higher wear rates were obtained at a high humidity than at a low humidity. As the sliding speed was increased, the wear rates were decreased and the effect of humidity on the wear rates of $Si_3N_4$ was reduced. The result that the $Si_3N_4$ pin showed higher wear rate under the high humidity condition was explained by the decrease in microhardness of $Si_3N_4$ due to the chemisorbed moisture on the pin and plowing action by the hard particles of $Fe_2O_3$ from the disk. An increase in the sliding speed is supposed to reduce the effect of humidity on the wear rate of $Si_3N_4$ by raising the average temperature of the disk surface and the local temperature at pin-disk contact point.

• Applied Science and Convergence Technology
• /
• 제26권6호
• /
• pp.208-213
• /
• 2017

Flexible opto-electronic devices are developed on the insulating layer deposited stainless steel (STS) substrates. The silicon dioxide ($SiO_2$) material as the diffusion barrier of Fe and Cr atoms in addition to the electrical insulation between the electronic device and STS is processed using the plasma enhanced chemical vapor deposition method. Noble silver (Ag) films of approximately 100 nm thickness have been formed on $SiO_2$ deposited STS substrates by E-beam evaporation technique. The films then were annealed at $650^{\circ}C$ for 20 min using the rapid thermal annealing (RTA) technique. It was investigated the variation of the surface morphology due to the interaction between Ag films and $SiO_2$ layers after the RTA treatment. The results showed the movement of Si atoms in silver film from $SiO_2$. In addition, the structural investigation of Ag annealed at $650^{\circ}C$ indicated that the Ag film has the material property of p-type semiconductor and the bandgap of approximately 1 eV. Also, the films annealed at $650^{\circ}C$ showed reflection with sinusoidal oscillations due to optical interference of multiple reflections originated from films and substrate surfaces. Such changes can be attributed to both formation of $SiO_2$ on Ag film surface and agglomeration of silver film between particles due to annealing.

• 대한금속재료학회지
• /
• 제50권8호
• /
• pp.575-582
• /
• 2012

Medium carbon steel was aluminized by hot dipping into molten Al or Al-1 at% Si baths. After hot-dipping in these baths, a thin Al-rich topcoat and a thick alloy layer rich in $Al_5Fe_2$ formed on the surface. A small amount of FeAl and $Al_3Fe$ was incorporated in the alloy layer. Silicon from the Al-1 at% Si bath was uniformly distributed throughout the entire coating. The hot dipping increased the microhardness of the steel by about 8 times. Heating at $700-1000^{\circ}C$, however, decreased the microhardness through interdiffusion between the coating and the substrate. The oxidation at $700-1000^{\circ}C$ in air formed a thin protective ${\alpha}-Al_2O_3$ layer, which provided good oxidation resistance. Silicon was oxidized to amorphous silica, exhibiting a glassy oxide surface.

• 한국주조공학회지
• /
• 제26권5호
• /
• pp.205-210
• /
• 2006

여러 전자기 재료 프로세싱 연구 중에서 연구 되어지지 않았던 Al-Si 합금의 조직제어를 직류 자기장과 교류 전류장을 사용하여 시도 하였다. 본 연구의 목적은 Al-Si 합금에서의 새로운 거시, 미시 조직제어를 하기 위해 사용된 전자기 진동의 영향을 조사하는 것이다. 전자기 진동이 초정 알루미늄의 형상 변화를 위해 낮은 진동수 (>60Hz)로 주어질 경우, 수지상의 형상이 구상화 형상으로 변해갔다. 전자기 진동이 공정 실리콘 형상 변화를 위해 주어졌을 경우, 높은 진동수 (>500Hz)에서 조대한 판상 조직이던 실리콘이 미세한 섬유상 조직으로 변화하고, 기계적 성질도 우수해졌다.

• Smart Structures and Systems
• /
• 제6권3호
• /
• pp.225-238
• /
• 2010

We report on the development of a new technology for the fabrication of Micro-Electro-Mechanical-System (MEMS) strain sensors to realize a novel type of crackmeter for health monitoring of ageing civil infrastructures. The fabrication of micromachined silicon MEMS sensors based on a Silicon On Insulator (SOI) technology, designed according to a Double Ended Tuning Fork (DETF) geometry is presented, using a novel process which includes a gap narrowing procedure suitable to fabricate sensors with low motional resistance. In order to employ these sensors for crack monitoring, techniques suited for bonding the MEMS sensors on a steel surface ensuring good strain transfer from steel to silicon and a packaging technique for the bonded sensors are proposed, conceived for realizing a low-power crackmeter for ageing infrastructure monitoring. Moreover, the design of a possible crackmeter geometry suited for detection of crack contraction and expansion with a resolution of $10{\mu}m$ and very low power consumption requirements (potentially suitable for wireless operation) is presented. In these sensors, the small crackmeter range for the first field use is related to long-term observation on existing cracks in underground tunnel test sections.

• 분석과학
• /
• 제15권3호
• /
• pp.236-242
• /
• 2002

RF 글로우 방전 원자 방출 분광법을 사용하여 다층 도금강판 두께분석을 하였다. 일반적으로 gas jet boosted 글로우 방전은 플라스마 안정성과 스퍼터링 효율이 우수하여 기존의 두께 분석법에서 측정이 어려운 다층 두께분석이 가능하며, RF를 사용하여 비전도성 실리콘-수지계열의 다층 도금강판 두께분석이 가능하였다. RF gas-jet boosted 글로우 방전은 방전전원과 가스 흐름량 그리고 방전압력에 의해 스퍼터링을 조절할 수 있다. 그래서 스퍼터링 효율에 의해 다층 도금된 강판의 경우 소재에 따라 서로 다른 조건에서 측정할 수가 있었다. 본 연구에서 두께 $20{\mu}m$의 아연층을 가진 아연 도금강판의 두께 및 조성을 분석하기 위해서 최적조건에 대한 연구를 하였고, 두 가지 기준물질로 구성된 수지 도금강판을 이용해서 검량선을 측정하였다. 본 연구에 최적조건 및 검량을 하기 위해서 아연합금 도금강판 및 실리콘-수지 도금강판은 포항 산업 과학 기술원(RIST)에서 제공하였다.

• Journal of Welding and Joining
• /
• 제24권4호
• /
• pp.15-21
• /
• 2006

The aim of present study is to investigate the effect of welding parameters and heat treatment conditions on the formability of the $CO_2$ laser welded silicon steel sheet. It was found that there is optimum range of the heat input ($0.6{\sim}0.7kJ/cm$) and gap distance ($0.125{\sim}0.150mm$) for the high tensile strength and the avoidance of the fracture in weld metal. Also, it was essential fur the improvement of formability to perform pre- and post-welding heat treatment which cause the uniform mixture of base metal and welding consumable.

• 한국표면공학회지
• /
• 제40권5호
• /
• pp.214-218
• /
• 2007

The objective of this study is to evaluate the diffusion behavior of Al and Si from a coatings in the microstucture of Fe-Si steel. Steel samples deposited with Al-Si alloy are prepared by ion plating process, followed by annealing treatments for diffusion at $1050^{\circ}C$. Several intermetallic phases are found in the coatings and they are identified as Fe-Al and an orderd Fe-Si compounds. Series of different concentration profiles through the sample have been obtained and Si content reaches about 5 wt% in case of 90 minutes of diffusion time.